Advertisement
Annotator 300 • Setup Guide (Continued)
Step 4 — Connecting control devices
a.
For RS-232 or IR control over DTP, connect to the 5-pole "Over DTP" captive screw connector (see
For control through Ethernet, connect a LAN or WAN to the RJ-45 connector (see
b.
192.168.254.254. The default subnet mask is 255.255.0.0.
c.
For serial RS-232 control, connect a host device to the 3-pole captive screw connector (see
The default baud rate is 9600.
For remote contact closure control, connect a host device to the 3-pole captive screw connector (see
d.
e.
For control through USB, connect a host device to the front panel mini USB port (see
Step 5 — Connecting user
Connect user interface devices (mouse and keyboard) or touch panels to the Annotator 300 using either of the rear panel USB ports (see
on page 1). Alternatively the front panel USB port can also be used to connect a user interface device.
H
Step 6 — Connecting power
Plug in a standard IEC power cord from a 100 to 240 VAC, 50-60 Hz power source into this power receptacle (see
Front Panel Overview
CAPTURE
USB
CONFIG
RECALL
A
B C
Front panel mini USB configuration port — Connect a control system or computer to this mini USB port (cable not supplied),
A
for device configuration, control, and firmware upgrading.
Front panel USB port — Connect an external drive to store or recall captured images, or connect a user
B
interface device.
Capture and Recall Buttons — Use these buttons to capture or recall captured images to or from a connected external drive,
C
network drive, or internal memory.
Input selection buttons and LEDs (1-3) — Select/switch inputs; LEDs indicate which input is active (current input lights green).
D
Auto Image Button — Pressing this twice initiates the Auto-Image
E
LCD display — This 16x2 screen displays device settings and menu configuration information.
F
Menu navigation buttons (Menu, Next) — These buttons allow navigation through the LCD menu system of the Annotator 300.
G
Adjust knobs — These are used with the menu navigation buttons to adjust the device settings and picture controls.
H
Setting the Front Panel Locks (Executive Modes)
The Annotator 300 has three modes of front panel security lock that limit the operation of the unit from the front panel.
Executive mode 0 (disabled) — The front panel is fully unlocked. This is the default setting.
Executive mode 2 (enabled) — The front panel is locked except for input switching. Can be set via front panel or by SIS command.
Executive mode 1 (enabled) — The front panel is completely locked and can be enabled and disabled only by SIS commands.
Enabling or Disabling Executive Mode 2 From the Front Panel
To enable Executive mode 2 or 0, press and hold the Menu and Next buttons simultaneously for 2 seconds. The display indicates that
Executive mode is either enabled or disabled. When the Annotator 300 is in Executive mode 0 (unlocked), this selects mode 2 (locked)
and if in Executive mode 2, this selects mode 0 (unlocked).
When either Executive mode (1 or 2) is enabled and a front panel action is attempted (other than input switching and Auto-Image), the
LCD displays the status for 2 seconds. Executive mode 1 can be enabled or disabled only by SIS commands.
Configuring the Annotator 300
The Annotator 300 can be configured either via front panel menus or through a host connected via RS-232, USB, or LAN connection.
Through a host connection, the Annotator 300 can be configured using Extron Product Configuration Software (PCS), embedded
webpages or by using Extron Simple Instruction Set (SIS) commands.
2
interface devices and touch panels
AUTO
INPUTS
IMAGE
1
2
3
D
E
See the online Annotator 300 User Guide for SIS commands.
on page 1). The default IP address is
J
K
on image below).
A
MENU
ADJUST
NEXT
F
G
H
function on the selected input.
™
on page 1).
G
on page 1).
on page 1).
I
a
on page 1).
ANNOTATOR 300
ANNOTATION GRAPHICS PROCESSOR
I J
Advertisement
