Control Cables - Alfa Romeo alfa 33 Workshop Manual

placed between support and body.
1 Lever
4 Lock nut
5 Bracket
2 Screws
3 Nut
DISASSEMBLY
W i t h r e f e r e n c e t o t h e f o l l o w i n g
exploded view remove the control
lever operating as follows.
cotter
1 . W i t h d r a w
1 Handle
2 Lever
3 Pushbutton
4 Spring
5 Stopper
6 Rod
7
8 Pin
CHECKS AND INSPECTIONS
1 . C h e c k components
against excessive wear and other
damages.
Check, in particular, surface con-
ditions of the lever coupling bush to
support, and wear conditions of pawl
teeth and scroll gear.
2. Check against presence of elec-
tric cable discontinuity and that
parking brake indicator switch is
properly functioning.
3 . R e p l a c e w o r n o r f a u l t y c o m -
ponents.
May 1983
FRONT AND REAR BRAKES
pin
adjusting fork @ , withdraw pin
this one from the lever.
2. Unscrew bolt @ securing the
lever to its relevant support @ and
separate the two components.
3 . W i t h d r a w b u s h
d l e @ f r o m l e v e r , r e m o v e p i n
stopper cotter @ on which ratchet
gear paw1 @ rotates and withdraw
the pin from its seat.
4. Separate from lever the whole
block of ratchet gear control with
p u s h b u t t o n 0, spring @, stop-
p e r 0, r o d @ a n d pawl 0.
5. If necessary, remove switch of
the parking brake indicator from
p i n f r o m brake support.
6 . 5 1 + 10.84)
Bush
9
Sector gear
10
Light switch
11
Bolt
12
support
13
Pin
14
15
REASSEMBLY
visually
For reassembly of the support and
lever unit,
assembly and, in particular comply
with the following:
ratchet gear components with speci-
fied grease (AGIP Fl Grease @or
SHELL Retinax Gll).
2. Tighten to specified torque of
9 t 15 N.m
(6.51 f 10.84 ft.lb) bolt hinging lever
to brake support.
h a n -
reverse the order of
(0.9 1.5
2 2 - 1 8
REINSTALLATION
T o r e i n s t a l l c o n t r o l l e v e r w i t h
support, reverse the order of removal
and complying with the following:
1. Apply a coat of specified grease
R e t i n a x Gll) t o s u r f a c e s w h e r e
cables slide in the incovered section
and to fork adjusting screw.
2. Carry out parking brake adjusT-
ment (see: Group 00 Chassis and
Body Maintenance).

CONTROL CABLES

REMOVAL
1 . O p e r a t i n g f r o m t h e d r i v e r s
compartment remove rear console
a n d , b y o p e r a t i n g l o c k n u t a n d
n u t o f a d j u s t m e n t f o r k l o o s e n
control cables and withdraw them
from equalizer.
2. Remove rear wheel and drum
together with hub (see: Group 25 -
Rear Hub - Removal).
3. Operating on wheel side release
control cable end @ from lever @
f a i r - l e a d @.
and free it from
Release control ,cable from brake
shoe holder 0, withdraw it from
this last and remove it after releasing
i t f r o m t h e u n d e r b o d y c l a m p s .
1 Brake shoe
3 Control cable
holder 4 Fair lead
2 Lever
CHECKS AND INSPECTIONS
Make sure that control cables are
sound; replace them if necessary.