ATTO Technology FibreBridge 7500 Installation And Operation Manual page 31

SASMapByTopology
SASMapByTopology specifies how target devices are mapped
to LUNs. When enabled, LUNs are numbered based on the SAS
topology, with gaps where there are open slots. When disabled,
LUNs are assigned to devices as they are discovered, which
may change over time.
set SASMapByTopology [enabled | disabled]
get SASMapByTopology
SASPortList
Lists the status of all available SAS ports.
SASPortList
SASTargets
Lists the physical devices that are connected to all SAS
connectors and PHYs.
SASTargets
SaveConfiguration
Many commands require a SaveConfiguration command to
be executed as indicated by the return Ready. *. When you
invoke a SaveConfiguration command, the current
configuration is permanently saved in the FibreBridge and the
new configuration becomes the active configuration. If a
firmware restart is required to make the requested change
permanent, you are asked to confirm the restart. You can
override this request by indicating the override value on the
command line. You may make several changes through
commands before implementing the restart, but once you have
restarted the FibreBridge, all the command changes created
before the restart and save are implemented. If you select the
restart option, the FibreBridge executes its complete start up
cycle.
SaveConfiguration <Restart | NoRestart>
SerialNumber
Reports the FibreBridge serial number. The serial number,
unique for each FibreBridge, is a 13-character field. The first
seven alphanumeric characters are an abbreviation of the
FibreBridge name while the remaining six numbers are the
individual FibreBridge board's number.
get SerialNumber
SerialPortBaudRate
SerialPortBaudRate configures the baud rate for the RS-232
serial port. The number of data bits per character is fixed at 8
with no parity.
Default: 115200
set SerialPortBaudRate [ 9600 |19200 | 38400 | 57600 |
115200]
Requires a SaveConfiguration Restart command
get SerialPortBaudRate
xi
ATTO Technology Inc. FibreBridge Installation and Operation Manual
SerialPortEcho
Control/reports the status of the display of keyboard input.
When enabled, all non-control character keyboard input is
output to the display. Local ASCII terminal (or terminal emulator)
echo settings should be set to disabled while using
SerialPortEcho enabled
Default: enabled
set SerialPortEcho [enabled | disabled]
Requires a SaveConfiguration Restart command
get SerialPortEcho
SNMP
Controls whether or not SNMP functions on the FibreBridge.
Default: disabled
set SNMP [enabled | disabled]
get SNMP
SNMPDumpMIB
Dumps the contents of the specified private SNMP MIB to the
current CLI session. If no parameter is specified, the Bridge
private MIB is dumped. For further assistance with SNMP,
consult your network administrator.
SNMPDumpMIB <Bridge | Product | SMI | TC>
SNMPExtendedTraps
Controls Extended SNMP trap functioning such as device
transition and device error. Consult your network administrator
for further assistance with SNMP.
Default: disabled
set SNMPExtendedTraps [enabled | disabled]
get SNMPExtendedTraps
SNMPTrapAddress
Sets/displays the IP trap addresses and levels.Consult your
network administrator for further assistance with SNMP.
Index: value between 1 and 6
IPAddress: standard IP address for the host
receiving messages; must be in the same subnet as
the FibreBridge
Trap Level: severity required for an event to trigger a
trap:
None: no traps are sent to the address
ALL: all triggering events are sent
Warning: warning and critical events are sent
Critical: only critical events trigger a trap
Default: 0.0.0.0 none
set SNMPTrapAddress [Index] [IPAddress] [None | All |
Warning | Critical ]
get SNMPTrapAddress [index]