System Programming Reference - AT&T Partner II Installation And Use Manual

System Programming Reference

System Programming changes settings for the system as a whole, or for individual lines or extensions. You can also use System Program-
ming to set up dialing restrictions, define groups, and set up optional equipment. Button-Down Mode (#723) can be activated (if needed)
before Line Ringing is set. Use Copy Settings (#399) to copy settings from one extension to another.
Place the Programming Overlay on the dial pad of the MLS display phone at extension jack 10 or 11
TO START SYSTEM PROGRAMMING
PRESS [ ] [ ] [ ]
Feature 0 0
PRESS [ ]
System Program
PRESS [ ]
System Program
TO END SYSTEM PROGRAMMING
PRESS [ ] [ ] [ ]
Feature 0 0
SYSTEM DATE
Sets the month, day, and year to appear on
display phones (MLS-34D and MLS-12D).
Include leading zeroes for single-digit
months or days (for example, January 3,
1992 is entered as 010392).
DIAL #101
DIAL the date in MMDDYY form
SYSTEM DAY
Sets the day of the week to appear on
display phones (MLS-34D and MLS-12D).
DIAL #102
1 = Sunday
DIAL
2 = Monday
3 = Tuesday
4 = Wednesday
5 = Thursday
6 = Friday
7 = Saturday
SYSTEM TIME
Sets the time to appear on display phones
(MLS-34D and MLS-12D). Enter four digits
in 24-hour military notation, from 0000 for
12 midnight to 2359 for 11:59 p.m. (for
example, 8:15 a.m. = 0815). System
displays times as a.m. or p.m.
DIAL #103
DIAL the time in HHMM form (military)
PBX DIAL-OUT CODE
This procedure identifies the digit you dial to
get out of the Centrex xyxtem to place an
outside call.
Dial #106
Dial the digit for the code (0–9) needed to call
out
= 9
= Factory Setting
= Troubleshooting procedure
(see Appendix C)
5-10 Programming Reference
TO USE A SPECIFIC PROCEDURE
DIAL [ ] and the three-digit procedure code
#
Example: [ ] [ ] [ ] [ ] for System Date
# 1 0 1
TO CYCLE THROUGH SYSTEM PROGRAMMING
PROCEDURES
PRESS [ ] or [
Next Procedure Prev Procedure
NOTE: Procedures #399, #609, #722, #723, and #728-
shown below in dashed boxes–are skipped when
cycling.
SYSTEM
RECALL TIMER DURATION
The Recall feature sends a timed
signal (switchhook flash) to the
Centrex system to which your premises
equipment is connected. This setting
changes the length of the signal in 25-
millisecond (msec) increments. (For
example, 01 = 25 msec, 80 = 2000 msec.)
Factory setting is correct for most
equipment. Change the factory setting
only if:
Using Recall drops calls (shorten the
time).
Using Recall has no effect— i.e.,
no dial tone (lengthen the time).
DIAL #107
DIAL two digits to set the length of a
switchhook flash (01 to 80)
= 18 (450 msec)
ROTARY DIALING TIMEOUT
Change the factory setting only if you
have trouble calling out on rotary lines
with standard touch-tone phones. (For
example, if users dial slowly and calls are
not completed or are connected to wrong
numbers, lengthen the timeout.) Use only
if the Dial Mode (#201) for at least one line
is set to "rotary."
DIAL #108
DIAL 1 = 4 seconds
2 = 8 seconds
3 = 12 seconds
TO CYCLE THROUGH AVAILABLE
SETTINGS
PRESS [
Next Data
TO RETURN TO DEFAULT SETTING
PRESS [
Remove
]
RESET LINE ASSIGNMENTS
Resets line assignments to what they were
when the premises equipment was first
started up: all lines are assigned to the
phone connected to extension jack 10, so
that a receptionist can view line activity
and cover lines; and every other extension
connected to the equipment controller is
assigned a single primary line. To assign
additional lines to an extension or to
remove a line assigned to an extension,
use Line Assignment (#301).
DIAL #722
BUTTON-DOWN MODE
Sets extension jacks 11-33 so that only the
extension's primary line (under the bottom
leftmost programmable button on an MLS- or
MLC-model phone) rings; any other lines
assigned to this extension will not ring unless
you use Line Ringing to change them. At
extension jack 10, the extension's primary line
rings immediately and all other lines ring after
a short delay.
DIAL #723
DIAL
1 = Not active
2 = Active
NOTE: This option overrides any current Line
Ringing settings that were specified using
Centralized Telephone Programming, After
activating this mode, use Centralized
Telephone Programming from extension jack
10 or 11 to adjust Line Ringing on specific
extensions.
SYSTEM RESET – PROGRAMMING
SAVED
IMPORTANT: Using this procedure
disconnects any active calls but retains
equipment controller settings. Use it only if
the equipment controller fails to function
correctly after a power failure or down
period.
DIAL #728
] or [ ]
Prev Data
]