AT&T PARTNER Plus Programming Quick Reference Manual
Hide thumbs
Also See for PARTNER Plus:
- Installation manual (26 pages) ,
- Installation manual (26 pages) ,
- Installation and programming manual (87 pages)
Subscribe to Our Youtube Channel
Related Manuals for AT&T PARTNER Plus
Summary of Contents for AT&T PARTNER Plus
- Page 1 MG9150J Issue 1 AT&T October 1995 PARTNER® Plus, PARTNER II Communications System Programming Quick Reference Graphics © AT&T 1988...
- Page 2 DIAL (optional) two-digit destination extension number NOTE: All page references are to PARTNER Plus and PARTNER II release 4.1 documentation. To order additional copies, call the DDC at 1-800-252-4076 or fax at 513-768-5514. Refer to document number MG9150J.
- Page 3 System Features Continued SAVE NUMBER REDIAL MANUAL SIGNALING GROUP CALLING—RING/PAGE P+ > R1.0 P+ 1 Grp < R2.0, 4 Grp > R3.0 (p. 5-64) P+ > R4.0 (p. 5-97) (p. 5-123) PII > R3.0 (p. 5-132) PII > R1.0 PII 4 Grp > R1.0 (p.
- Page 4 System Programming Quick Reference Place the Programming Overlay on the dial pad of the system display phone at extension 10 or 11 P+ > R 3.0, PII > R1.0 TO CYCLE THROUGH AVAILABLE TO CYCLE THROUGH SYSTEM TO START SYSTEM PROGRAMMING TO END SYSTEM PROGRAMMING PROGRAMMING PROCEDURES SETTINGS PRESS [...
- Page 5 Lines GROUP CALL DISTRIBUTION DIAL MODE P+ > R3.1 (p. 5-62) P+ > R1.0 (p. 5-36) PII > R3.0 (p. 5-94) PII > R1.0 (p. 5-58) DIAL #206 DIAL #201 DIAL a group number (1–6, 7 for DIAL a line number (01–12 P+,01– VMS) 24 PII) DIAL...
- Page 6 System Programming Quick Reference Place the Programming Overlay on the dial pad of the system display phone at extension 10 or 11 TO START SYSTEM PROGRAMMING TO END SYSTEM PROGRAMMING TO CYCLE THROUGH SYSTEM TO CYCLE THROUGH AVAILABLE PROGRAMMING PROCEDURES SETTINGS PRESS [ PRESS [...
- Page 7 SYSTEM RESET – PROGRAMMING SAVED (p. 5-138) P+ > R1.0 PII > R1.0 (p. 5-181) IMPORTANT: Using this procedure disconnects any active calls but retains system settings. Use it only if the system fails to function correctly after a power failure or down period. DIAL #728 Dialing Restrictions and Permissions OUTGOING CALL RESTRICTION...
- Page 8 System Programming Quick Reference Place the Programming Overlay on the dial pad of the system display phone at extension 10 or 11 TO CYCLE THROUGH SYSTEM TO CYCLE THROUGH AVAILABLE TO START SYSTEM PROGRAMMING TO END SYSTEM PROGRAMMING PROGRAMMING PROCEDURES SETTINGS PRESS [ PRESS [...
-
Page 9: Programming Mixed Telephone Types
Programming Mixed Telephone Types Overview This appendix provides information about programming from a PARTNER-34D phone to MLS-model phones and from an MLS-34D phone to PARTNER-model phones. In these situations, you should be aware that the button that you press at extension 10 or 11 (the programming extension) is likely to be in a different location than the button on the phone to which the programming applies (the target phone). - Page 10 PARTNER-34D Overlay MLS-6 Phone MLS-18D/12D/12 Phone PARTNER-18D Overlay MLS-34D Phone Figure 1. Programming from a PARTNER-34D Phone...
- Page 11 MLS-34D Overlay PARTNER-6 Phone PARTNER-18D/18 Phone PARTNER-34D Phone MLS-18D/MLS-12D Overlay Figure 2. Programming from a MLS-34D Phone...
- Page 12 System Identifier The System Identifier feature allows a PARTNER, PARTNER PLUS or PARTNER II system to identify its release number to NSAC personnel. While speaking with the customer, ask them to dial [ ]. The beeps heard immediately Feature after entering this code is used to identify the users model and release number according to the table...
Need help?
Do you have a question about the PARTNER Plus and is the answer not in the manual?
Questions and answers