Parts List; Metric / Inch Scale - GREAT PLANES Ryan STA Instruction Manual

• Whenever the term glue is written you should rely upon
your experience to decide what type of glue to use. When a
specific type of adhesive works best for that step the
instructions will make a recommendation.
• Whenever epoxy is specified you may use either 30-
minute epoxy or 6-minute epoxy. When 30-minute epoxy is
specified it is highly recommended that you use only 30-
minute (or 45-minute) epoxy because you will need the
working time and/or the additional strength.
1
18
16
1 Wing and Ailerons
2 Fuselage
3 Stab and Elevators
4 Fin and Rudder
5 Cowl
6 Cowl Ring
7 Wheel Pants
8 Rudder Fairing
9 Turtledeck
10 Fin Fairing
11 Stab Fairings
12 Wing Bolt Plate
13 Forward Wing Joiner
14 Wing Struts
15 Dorsal Fin
16 Engine Mount
17 Fuel Tank
18 Windscreen
19 Cockpit Coaming
20 Wing Dowels
21 Cowl Mount Blocks
Inch Scale
0" 1"
0 10 20 30
Metric Scale
10
11
15
7
5
17

Parts List

Not Pictured:
Main Landing Gear
Tail Gear with Tailwheel
Aft Wing Joiner
Forward Servo Tray
Aft Servo Tray
Instrument Panel Decal
Hardware Bag
Replacement Parts:
GPMA2200 Wing Set
GPMA2201 Fuse Set
GPMA2202 Tail Set
GPMA2203 Cowl Set
GPMA2204 Windscreen
GPMA2205 Landing Gear Set
GPMA2206 Wheel Pants
GPMA2207 Wing Struts
GPMA2208 Rudder Fairing
To convert inches to millimeters, multiply inches by 25.4
2"
40 50 60 70
• When you get to each step, read that step completely
through to the end before you begin. Frequently there is
important information or a note at the end of the step that
you need to know before you start.
• Photos and sketches are placed before the step they
refer to. Frequently you can study photos in following steps
to get another view of the same parts.
Parts List
8
12
2
13
19
21
6
20
14
(1) 60-120 Engine mount
(2) Metal solder-on clevis
(2) Brass body for screw-lock
pushrod connector
(4) Large nylon control horns
(2) 1/4-20 x 2" nylon wing bolts
(3) Nylon clevis
(2) Hump strap for 1/8" wire
(2) Trees of 4 flat nylon LG straps
(1) Ball link
(2) Nylon retainers for screw-lock
(1) CA hinge strip
(2) Nylon faslinks
(2) 6-32 torque rod horn
(2) 4-40 hex nuts
(4) 8-32 blind nuts
(1) 0-80 hex nut
(1) 3/16" x 36" guide tube
(7) Silicone retainers
(2) 6-32 set screws
(2) 6-32 x 1/4" cap screws
3" 4"
80 90 100 110 120 130 140 150 160 170 180
5
3
4
9
7
1
Hardware
(7) #4 x 5/8" screws
(1) 0-80 threaded ball
(4) 2-56 x 3/4" cap screws
(4) 8-32 x 1-1/4" cap screws
(4) 8-32 x 1" cap screws
(2) 4-40 x 1/8" cap screws
(36)#2 x 1/2" screws
(4) 3/16" wheel collars
(1) 2-56 x 12" threaded pushrod
(1) 2-56 x 36" threaded pushrod
(2) 2-56 x 6" threaded pushrods
(2) 4-40 x 36" threaded pushrods
(1) 6-32 x 1-1/2" threaded rod
(3) #4 flat washer
(8) #8 lock washer
(4) #8 flat washer
(2) Axles
5" 6" 7"