Table of Contents
Advertisement
Do not fly unless your propeller, spinner and
spinner backplate are precision balanced, using a
"high-point" or similar balancer.
Do not use a propeller that will produce exces-
sively high speeds. 6" Pitch is recommended for 2-
cycle engines, and 8" pitch is recommended for 4-cy-
cles.
PART#
QTY
DESCRIPTION
CANPY037
Clear Plastic Canopy
PLTB002
Plastic 36" Outer Pushrod
Tubes
SS90F01
Balsa Shaped 3/16 Fuselage
Side
SS90F05
Balsa Shaped 13/16 Chin
Block
SS90F06
Hardwood Shaped 5/8 Engine
Mount Rail
SS90F27
Balsa 3/8x1-3/8x21-1/4
Hood Side Block
SS90F32
3-Ply 1/8 DC* Fuse Doubler
SS90P01
Fuselage Plan
SS90P02
Wing Plan
SS90P03
Instructions
WIRES17
Wire 2-56 x 34" Pushrod,
Threaded One End
WPNTS003
ABS Plastic Wheel Pants Set
SS90A01
HARDWOOD PARTS
PLY3021
3-Ply 1/16 DC Spinner Ring
PLY3022
3-Ply 1/16 DC Landing Gear
Braces
SS90F03
5-Ply Shaped 3/8 F-l
Firewall
SS90F08
5-Ply 1/4x1-1/2x4-5/16
Wing Bolt Plate
SS90F18
5-Ply 3/16 x 1/2 x 4-3/32 Servo
Rails
SS90F41
3-Ply 1/32 x 1 x 1 Spinner
Ring Spacer
SS90F43
3-Ply 1/8 X 3/8 X 3-5/8 Servo
Rail Supports
SS90F44
5-Ply 1/4x1x1 Stab
Reinforcement Block
5-Ply Shaped 1/4 Front Stab
5590503
Brace
5590504
5-Ply 1/4x1/2x6
Rear Stab Brace
SS90W17
Hardwood 5/16 Diax 4-1/2
Wing Dowel
SS90W18
Hardwood 1/2 x 3/4 x 7-3/4
Landing Gear Block
SS90W19
Hardwood 1/2 x 3/4 x 29/32
Landing Gear Block Support
Hardwood 1/2 x 3/4 x 1/2
SS90W20
Landing Gear Block Gusset
SS90W21
5-Ply 1/8x1-3/4x1-3/4
Wheel Pants Screw Plate
SS90W22
3-Ply 1/16x1x1 Wing
Bolt Plate
SS90W32
5-Ply 1/8 x 3/8 x 5/8
Aileron Servo Rail
f f
Note: "DC"
Die Cut
Before each flight, inspect the clevises, horns,
pushrods and all other parts of the control linkages,
checking for any play that may have developed due
to wear. Especially watch for enlargement of the
holes in the nylon horns and servo arms, loose screws
and nuts, and worn servo mounting grommets. Re-
place worn parts immediately.
GOOD LUCK AND GREAT FLYING!
PARTS LIST PART#
SS90A02
SS90F20
SS90F26
SS90F29
SS90F30
SS90F42
SS90A03
SS90F09
SS90F10
SS90F11
SS90F12
SS90F16
SS90F17
SS90F19
SS90F21
SS90F25
SS90F28
SS90F40
SS90R02
SS90R03
SS90S02
SS90A04
SS90W33
SS90W34
SS90W35
SS90A05
SS90F34
SS90F35
SS90F37
41
QTY
DESCRIPTION
1 BALSA FUSELAGE
PARTS
Balsa Shaped 3/16 Rear
Fuse Side
Balsa 7/8 Fin Fairing
Balsa 1/2 Upper
Nose Side
Balsa Shaped 1/2 Lower
Nose Side
Balsa 1/2x5/8x4-13/16
Nose Side Fillers
BALSA FUSELAGE
1
PARTS
1
Balsa Shaped 1/4 F-3A
Bulkhead
1
Balsa Shaped 1/4 F-6A
Bulkhead
1
Balsa Shaped 5/8x3x3-1/2
Spinner Filler
1
Balsa 3/8x1/2x3-5/8
Nose Filler
1
Balsa 3/8x15/16x2-1/32
•
Stab Filler Block
1
Balsa 1/4x7/8x4-5/16
Fuse Cross-Brace
2
Balsa Shaped 3/16 Front
Fuse Side
1
Balsa Tapered 1/4 Tail Filler
1
Balsa 3/8x1x1 Fin Fairing
2
Balsa 3/16x5/8x4-7/8
Engine Rail Filler
1
Balsa 1/8x2-1/4x4
Fuel Tank Support
1
Balsa Shaped 1/4 Front
Fin Filler
1
Balsa 1/4 x 3 x 1-1/2 Rear
Fin Filler
1
Balsa 1/4x3-7/32x3
Stab Center
1
DIE CUT WING RIBS
8
Balsa 3/32 DC W-3 Wing Rib
Sheet
3
Balsa 3/32 DC W-2 Wing Rib
Sheet
1
Balsa 3/32 DC W-l Wing Rib
Sheet
DIE CUT FORMERS
3-Ply 1/8 DC Formers 5A,
4A,3B
3-Ply 1/8 DC Formers 1A,
1B,2A,2D
3-Ply 1/8 DC Formers F2,
F3.AB
Advertisement
Table of Contents
