Building Stand; Important Building Notes; Ordering Replacement Parts - GREAT PLANES Cherokee .40 ARF Instruction Manual

❏
Pliers with wire cutter (HCAR0630)
❏
Hobbico Duster ™ can of compressed air (HCAR5500)
❏
Switch & Charge jack mounting set (GPMM1000)
❏
Rotary tool such as Dremel
❏
Rotary tool reinforced cut-off wheel (GPMR8020)
❏
Servo horn drill (HCAR0698)
❏
™
Hobby Heat micro torch II (HCAR0755)
❏
Precision magnetic prop balancer (TOPQ5700)
❏
AccuThrow ™ defl ection gauge (GPMR2405)
❏
C.G. Machine ™ (GPMR2400)
❏
Hobbico fl exible 18" ruler stainless steel (HCAR0460)
❏
Top Flite MonoKote trim seal iron (TOPR2200)
❏
Top Flite MonoKote heat gun (TOPR2000)
❏
Hobbico pin vise 1/16" collet w/6 Bits (HCAR0696)
❏
Hobbico 8-piece ball tip hex L wrench SAE (HCAR0520)
❏
Hobbico 7-piece ball tip hex L wrench Metric (HCAR0521)
❏
Great Planes clevis installation tool (GPMR8030)

BUILDING STAND

A building stand or cradle comes in handy during the build.
We use the Robart Super Stand II (ROBP1402) for all our
projects in R&D, and it can be seen in pictures throughout
this manual.

IMPORTANT BUILDING NOTES

• When you see the term test fi t in the instructions, it
means that you should fi rst position the part on the assembly
without using any glue, then slightly modify or custom fi t
the part as necessary for the best fi t.
• Whenever the term glue is written you should rely upon
your experience to decide what type of glue to use. When
a specifi c type of adhesive works best for that step, the
instructions will make a recommendation.
• Whenever just epoxy is specifi ed you may use either
30-minute (or 45-minute) epoxy or 6-minute epoxy. When
30-minute epoxy is specifi ed it is highly recommended that
you use only 30-minute (or 45-minute) epoxy, because you
will need the working time and/or the additional strength.
®
• Photos and sketches are placed before the step they
refer to. Frequently you can study photos in following steps
to get another view of the same parts.
• The stabilizer and wing incidences and engine thrust
angles have been factory-built into this model. However,
some technically-minded modelers may wish to check these
measurements anyway. To view this information visit the web
site at www.greatplanes.com and click on "Technical Data."
Due to manufacturing tolerances which will have little or no
effect on the way your model will fl y, please expect slight
deviations between your model and the published values.

ORDERING REPLACEMENT PARTS

Replacement parts for the Great Planes Cherokee .40 ARF are
available using the order numbers in the Replacement Parts
List that follows. The fastest, most economical service can be
provided by your hobby dealer or mail-order company.
To locate a hobby dealer, visit the Hobbico web site at
www.hobbico.com. Choose "Where to Buy" at the
bottom of the menu on the left side of the page. Follow the
instructions provided on the page to locate a U.S., Canadian
or International dealer.
Parts may also be ordered directly from Hobby Services by
calling (217) 398-0007, or via facsimile at (217) 398-7721,
but full retail prices and shipping and handling charges will
apply. Illinois and Nevada residents will also be charged
sales tax. If ordering via fax, include a Visa
number and expiration date for payment.
Mail parts orders and payments by personal check to:
Hobby Services
3002 N. Apollo Drive, Suite 1
Champaign, IL 61822
Be certain to specify the order number exactly as listed in
the Replacement Parts List. Payment by credit card or
personal check only; no C.O.D.
5
® ®
or MasterCard