Canon iPF605 Service Manual page 45

[Paper Details]
(The paper type is displayed here.)
[GL2 Settings]
Setting Item
[GL2 Replot]
[GL2 BufferClear]
[Color Mode]
[Print Quality]
[Input Resolution]
[Media Source]
[Conserve Paper]
[End Point Shape]
[Smoothing]
[Line Width]
[ThickenFineLines]
[AdjustFaintLines]
Setting Item
[Roll DryingTime]
[Scan Wait Time]
[Feed Priority]
[Adjust Length]
[Head Height]
[Skew Check Lv.]
[VacuumStrngth]
[NearEnd RollMrgn]
[Cut Speed]
[Trim Edge First]
[Cutting Mode]
[Bordless Margin]
[CutDustReduct.]
[Manual Feed]
[NearEnd Sht Mrgn]
[Return Defaults]
Reprint the last printed page stored in the printer.
Delete the last printed page stored in the printer.
Choose the color mode.
Choose the print quality.
Select [600dpi] or [300dpi] as the print resolution.
Select the method of feeding paper when using the HP-GL/2 for printing.
Print using paper sparingly.
Select [Software] or [Round] as the shape of the line end.
Select whether to print an arc with a smooth curve or polygon.
Select the printing line width for the data for which a line width is not specified.
Choose On to print the thin line clearly.
Choose On if the colored of thin line is printed different from other figure. However, it is a possibility to the
thin lines become interrupted lines according to the some colors.
T-1-15
Description, Instructions
Specify the time to wait for the ink to dry for each sheet.
Specify the time to wait for the ink to dry between each scan in bidirectional printing,
in consideration of how quickly the paper absorbs ink. Note that printing will take
longer if you specify a wait time.
Specify exact paper feeding, if desired. Normally, select Automatic . Choose Print
Length if you prefer to feed the paper an exact amount. However, note that choosing
Print Length may result in slight banding in the direction of Carriage scanning.
Displayed if Feed Priority is Print Length .
Adjustment relative to the amount of stretching or shrinkage of the current paper.
For paper that tends to stretch, increase the feed amount by setting the adjustment
value toward +. For paper that tends to shrink, decrease the feed amount by setting
the adjustment value toward -.
The setting for the amount of paper stretching or shrinkage is relative. If you access
it again later, it will be displayed as 0.00 %.
Adjust the Printhead height.
If you print on Japanese Paper Washi or other handmade paper that has an irregular
width, choose Loose for a higher skew detection threshold, or choose Off to disable
skew detection. However, if paper is loaded askew when detection is Off , note that
paper jams or Platen soiling may occur.
If strict skew detection is required, choose High Accuracy.
Specify the level of suction that holds paper against the Platen .
Specify a margin at the leading edge of roll paper to ensure better printing quality at
the leading edge.
Note that if you choose 3 mm , it may lower the printing quality at the leading edge
and affect feeding accuracy. The printed surface may be scratched, and ink may
adhere to the the leading edge.
Choose the cutting speed. For media such as film that are more likely to generate
debris when cut, choose Fast to reduce the amount of debris.
If a roll is loaded, the end of the paper will be cut.
Choose Forced to have 40 mm (1.6 in) cut off the leading edge of the roll, ensuring
a straight edge, after you load the roll. Scraps are then removed.
When Automatic is selected, if the left and right side of the leading edge of the roll
are uneven (by 3 mm [0.12 in] or more), the edge is cut an amount relative to the
slant to ensure a straight edge after you load the roll. Scraps are then removed.
If the unevenness is less than 3 mm or if No Cutting is selected, the edge is not cut
and scraps are not removed.
Specify if the Cutter Unit is used for cutting.
Choose Automatic to have roll paper cut automatically after printing. If you choose
Eject , the paper will not be cut after printing. Instead, a line will be printed at the
cut position.
Adjust the margin during borderless printing.
Choose On to reduce the amount of debris generated when cutting film and similar
media by printing a line at the cut position. This option reduces the amount of debris
given off after cutting.
Choose how the paper is supplied, Top for printing from the Tray or Front for
printing from the Front Paper Feed Slot .
Specify a margin at the leading edge of sheets to ensure better printing quality at the
leading edge.
Note that if you choose 3 mm , it may lower the printing quality at the leading edge
and affect feeding accuracy. The printed surface may be scratched, and ink may
adhere to the the leading edge.
If you have selected 20 mm , the test print sheet may not be printed completely.
Choose Yes to restore Med.Detail Set. to the factory default values.
T-1-16
Description, Instructions
Chapter 1
1-31