Fujitsu MAA3182FC Series Manual page 317

Changing the reserve conditions 4 - 74, 4 - 76
Charge 1 - 12
CHECK CONDITION status 2 - 7
Class 3 Service Parameter 1 - 38
CLEAR TASK SET 2 - 24
CN1 1 - 11
Combination of error recovery flags 4 - 25
Combination of SOF and EOF 2 - 11
Command code 2 - 3
Command completion wait time-out 5 - 11
Command Descriptor Block 1 - 63
Command Execution 2 - 12
Command Format 2 - 1
Command inherent information 5 - 4
Command link 2 - 14
COMMAND phase 1 - 77
Command Processing 2 - 1
Command Processing Exceptions 2 - 19
Command processing in the not ready state
2 - 20
COMMAND Protocol 1 - 77
Command Queuing Function 2 - 15
Command Specifications 4 - 1
COMMAND TERMINATED status 2 - 7
Command Transfer 1 - 24
COMMAND, WRITE phase 1 - 77
Commands cleared by another INIT 2 - 17
Commands that can be executed 2 - 21
Common Service Parameter 1 - 36
Communication between Initiator and Target
1 - 24
Comparison between FC and SCSI about
definition 2 - 23
CONDITION MET Status 2 - 7
Connect time limit 4 - 31
Control byte 2 - 5
Control commands 4 - 1
Control Field 1 - 62
Control mode parameters 4 - 48
Correctable bit length 4 - 24, 4 - 42
Correctable data read error 5 - 21
Cylinder count 4 - 39
Cylinder skew factor 4 - 36
D
D List 4 - 93, 4 - 97, 6 - 1
Data Access Commands 4 - 81
Data Block Addressing 2 - 27
Data block count 4 - 18, 4 - 67
Data block length 4 - 18, 4 - 68
Data Block Verification Methods 6 - 7
Data Buffer 3 - 1
Data buffer configuration 3 - 2
IN - 2
Data buffer configuration and basic operation
3 - 1
Data Buffer Management 3 - 1
Data byte length/physical sectors 4 - 36
Data category on the Loop 1 - 5
Data defect list 4 - 93
Data space configuration 2 - 28
Data transfer disconnect control 4 - 32
Data Transfer Protocol 1 - 75
Data transfer sequence 2 - 8, 2 - 9
Data which are objects of caching 3 - 7
DCR 4 - 24
DCRT 4 - 96
DDIS 4 - 55
Decoding 1 - 4
Defect data configuration 4 - 108
Defect descriptor 4 - 99
Defect descriptor list 4 - 109
Defect descriptor: physical sector address
format 4 - 99
Defect list 4 - 93, 4 - 97
Defect list format 4 - 109
Defect list length 4 - 97, 4 - 109
Defect lists 6 - 1
Defect Management 6 - 1
Defect processing during initialization 4 - 101
Definition of COMMAND bytes 1 - 77
Definition of data space 2 - 27
Definition of mated control 1 - 13
Destination device where data are to be
transferred 2 - 10
Detail errors and action 1 - 73
Detailed information 5 - 9
Device serial No. 4 - 8
Device Serial Number field 4 - 7
Device type code 4 - 4
Device type qualifier 4 - 4
DEXCPT 4 - 56
Disable certification 4 - 96
Disable correction 4 - 24
Disable discovery 4 - 55
Disable exception control 4 - 56
Disable loop master 4 - 55
Disable primary 4 - 96
Disable queuing 4 - 49
Disable read-ahead 4 - 48
Disable soft address 4 - 54
Disable target initiated port enable 4 - 54
Disable target originated loop initialization
4 - 54
Disable transfer on error 4 - 23
Disabling caching data 3 - 8
DISC 4 - 45
Disconnect immediate 4 - 33
C141-E054-02EN