Advanced Setup List - Yamaha YSP-5600 Owner's Manual

Advanced setup list

Menu
TURN ON VOLUME OFF (Not set) (default), 1 to 70
MAX VOLUME 1 to 99, MAX (Maximum) (default)
ON (INPUT key operation is disabled)
INPUT LOCK
OFF (INPUT key operation is enabled) (default)
ON (Key operation on the unit is disabled)
PANEL LOCK
OFF (Key operation on the unit is enabled) (default)
ON (Enables power-on)
IR INPUT POWER
OFF (Disables power-on) (default)
ON (Enters standby mode) (default)
AC ON STANDBY
OFF (Restores the state before power was lost)
ON (Protect is performed)
MEMORY PROTECT
OFF (Protect is not performed) (default)
YES (The reflection board is used)
YRB FL
NO (The reflection board is not used) (default)
YES (The reflection board is used)
YRB FR
NO (The reflection board is not used) (default)
YES (The reflection board is used)
YRB SL
NO (The reflection board is not used) (default)
YES (The reflection board is used)
YRB SR
NO (The reflection board is not used) (default)
ON (This unit turns off automatically) (default setting for U.K.,
Europe and Russia models)
AUTO POWER STANDBY
OFF (This unit does not turn off automatically) (default setting
other than U.K., Europe and Russia models)
ON (Notify) (default)
NOTICE OF NEW FW
OFF (Do not notify)
01.02 (The firmware version is displayed)
FW UPDATE
Start OK? (Firmware is updated)
INFO (Initialize all settings not related to the network)
INITIALIZE NET INFO (Initialize network related settings)*
CANCEL (Do not initialize) (default)
• Initializing this unit also initializes measurement results with IntelliBeam and settings stored in system memory. Perform "AUTO SETUP" from the "IntelliBeam" menu again (p. 30).
Settings/Adjustable range
Set the initial volume level when the power of this unit is turned on.
When set to "OFF", volume level is the same as when this unit is turned off.
Set the maximum volume level so that this unit will not output sound beyond the limited volume level.
Select whether or not to enable the INPUT key on the unit.
Select whether or not to enable key operations on the unit (except the advanced setup operations).
Select whether or not to automatically turn on this unit by pressing an input selector key on the remote
control when the unit is turned off.
Set this unit's power to off when the AC power is recovered after the power to this unit was lost temporally
(disconnect the AC power plug from the wall outlet, power outage, etc.).
Protect settings stored in system memory, and Internet radio stations registered with the unit.
Use the YRB-100 sound reflection board for the front left channel. Refer to page 100 for details of YRB-100.
Use the YRB-100 sound reflection board for the front right channel. Refer to page 100 for details of
YRB-100.
Use the YRB-100 sound reflection board for the surround left channel. Refer to page 100 for details of
YRB-100.
Use the YRB-100 sound reflection board for the surround right channel. Refer to page 100 for details of
YRB-100.
When set to "ON", this unit turns off automatically in any of the following situations:
• Audio is coming from the selected input source, but no operations have been performed for 8 hours or
more.
• HDMI1– 4, Bluetooth or NET is selected as the input source, but no audio has been input to the unit or no
operations have been performed with the unit for more than 20 minutes.
Notifications will not be displayed on the TV screen when updates for the unit's firmware are provided via
the network.
Confirm firmware version/update firmware.
Reset the parameters of this unit to the factory presets. When the unit freezed, the problem may solve by
restoring to their default values.
* The following configurations will be restored if "INFO" is selected.
• Network Standby (p. 82)
• Bluetooth (p. 46)
Description
SETTINGS ➤ Advanced setup
87
En