Table of Contents
Advertisement
Quick Links
PLATINUM SMART-HEAT™
ELECTRIC HEATER SERIES II
BY BROMIC
INSTALLATION, INSTRUCTION AND
SERVICE MANUAL
AVAILABLE IN 2300W VERSION
!
IMPORTANT
READ THIS MANUAL CAREFULLY.
Original Instructions
SEE INSIDE COVER FOR IMPORTANT INFORMATION ABOUT
THIS MANUAL. KEEP INSTRUCTION WITH APPLIANCE FOR
FUTURE REFERENCE.
Version 2.0 EU
Advertisement
Table of Contents
Related Manuals for Bromic Heating PLATINUM SMART-HEAT ELECTRIC HEATER SERIES II
Summary of Contents for Bromic Heating PLATINUM SMART-HEAT ELECTRIC HEATER SERIES II
- Page 1 PLATINUM SMART-HEAT™ ELECTRIC HEATER SERIES II BY BROMIC INSTALLATION, INSTRUCTION AND SERVICE MANUAL AVAILABLE IN 2300W VERSION IMPORTANT READ THIS MANUAL CAREFULLY. Original Instructions SEE INSIDE COVER FOR IMPORTANT INFORMATION ABOUT THIS MANUAL. KEEP INSTRUCTION WITH APPLIANCE FOR FUTURE REFERENCE. Version 2.0 EU...
- Page 2 IMPORTANT This manual contains important information about the installation, operation, and maintenance of Platinum Smart-Heat™ Electric Heaters. Please pay close attention to the important safety information shown throughout this instruction manual. Any safety information will be accompanied by the following safety alert symbols: DANGER, WARNING,...
-
Page 3: Table Of Contents
CONTENTS IMPORTANT NOTES & WARNINGS PRODUCT OVERVIEW PRODUCT DESCRIPTION SPECIFICATIONS PRODUCT FEATURES HEATER INSTALLATION INSTRUCTIONS CEILING & WALL MOUNTING CEILING RECESS TUBE SUSPENSION ELECTRICAL INSTALLATION SERVICING TROUBLESHOOTING www.bromicheating.com... -
Page 4: Important Notes & Warnings
IMPORTANT NOTES AND WARNINGS WARNING licenced service person only. The heater should be inspected before use and at least annually serviced and inspected by a qualified and licenced service person. • IMPORTANT - Installation MUST be carried out by a licensed and authorised person. -
Page 5: Product Overview
IMPORTANT NOTES AND WARNINGS CONTINUED • Keep the cable away from sharp edges during handling and • Do not install the heater directly near a bathtub, shower or installation. swimming pool. Any switches or controls must not be within reach of a person in the bathtub, shower or swimming pool. -
Page 6: Heater Installation Instructions
HEATING INSTALLATION INSTRUCTIONS CEILING & WALL MOUNTING • Heaters must be installed according to the minimum • Minimum distance from edge of heaters to any installation clearances shown in these diagrams adjacent walls must be at least 250mm. Heaters must •... - Page 7 HEATING INSTALLATION INSTRUCTIONS CONTINUED... OPTION 1 To exit the cable through the side of the wall mounting bracket, start from step 1. 1. Unscrew and remove plug-in wall bracket (a). 2. Attach extra supplied cable gland into the same hole from the outside of the bracket. Fasten in place with the metal cable gland nut from inside the bracket (b).
- Page 8 9. Fit the smaller cover over the heater bracket so that the slots pass over the HEATING INSTALLATION INSTRUCTIONS shafts of the M6x14mm mounting screws (i). Fit the larger cover over the CONTINUED... smaller cover in the same way from the opposite side of the bracket (j). 8.
-
Page 9: Ceiling Recess
HEATING INSTALLATION INSTRUCTIONS CONTINUED... CEILING RECESS (SOLD SEPARATELY) WARNING Minimum vertical ceiling space clearance between the heater WARNING frame and ceiling surface must be 250mm. Instructions below are suitable for ceiling surfaces 10-30mm Minimum horizontal ceiling space clearance measured from each thick. -
Page 10: Tube Suspension
the 4 M5 screws and nuts provided (k). HEATING INSTALLATION INSTRUCTIONS 12. Remove the 4 M5 screws fastening the heater CONTINUED... mounting bracket to the back of the heater. Re-insert the screws with both halves of the ceiling support bracket in place and tighten firmly. -
Page 11: Electrical Installation
ELECTRICAL INSTALLATION WARNING ELECTRICAL INSTALLATION This heater MUST be permanently installed by an authorised/ Check product label for correct voltage and wattage licenced person. Do not perform maintenance, or carry out to ensure sure power source conforms to the heaters installation or assembly procedure while electrical power is requirements.