Table of Contents
Advertisement
Quick Links
LPG / ULPG MOBILE INDUSTRIAL DIRECT
FIRED AIR HEATER
BY BROMIC
INSTALLATION, INSTRUCTION AND
SERVICE MANUAL
MODELS:
HF15 / HF20 / HF30 / HF50
WARNING: THIS HEATER IS APPROVED FOR
Version 5.0 AUS
INDUSTRIAL USE ONLY
IMPORTANT: This heater should be installed and
operated in accordance to the manufacturers
instructions outlined within this manual. The user
shall ensure that local gas fitting regulations,
municipal building codes, AS/NZS 1596
other relevant statutory regulations are adhered
to. Use appliance only in a well-ventilated
space. Read and understand this manual before
attempting to assemble, operate and service the
appliance. Keep this manual for future reference.
and
Advertisement
Table of Contents
Related Manuals for Bromic Heating HEAT-FLO HF15
Summary of Contents for Bromic Heating HEAT-FLO HF15
- Page 1 LPG / ULPG MOBILE INDUSTRIAL DIRECT FIRED AIR HEATER BY BROMIC INSTALLATION, INSTRUCTION AND SERVICE MANUAL MODELS: HF15 / HF20 / HF30 / HF50 WARNING: THIS HEATER IS APPROVED FOR INDUSTRIAL USE ONLY IMPORTANT: This heater should be installed and operated in accordance to the manufacturers instructions outlined within this manual.
- Page 2 IMPORTANT This manual contains important information about the assembly, operation, and maintenance of Blow Heaters. Please pay close attention to the important safety information shown throughout this instruction manual. Any safety information will be accompanied by the following safety alert symbols: DANGER, WARNING, IMPORTANT...
-
Page 3: Table Of Contents
CONTENTS GENERAL HAZARD WARNING WHEELS ASSEMBLY (FOR HF30/50 ONLY) VENTILATION OXYGEN DEPLETION CARBON MONOXIDE (CO) POISONING GUIDELINES OF FUEL GASES OPERATING INSTRUCTIONS START-UP OPERATION SWITCHING OFF THE HEATER EMERGENCY SHUTDOWN SPECIFICATIONS TROUBLE SHOOTING MAINTENANCE AND STORAGE SERVICING INSTRUCTIONS FOR QUALIFIED TECHNICIANS ELECTRICAL COMPONENT SERVICE GAS COMPONENT SERVICE BURNER SERVICE... -
Page 4: General Hazard Warning
GENERAL HAZARD WARNING: IMPORTANT SAFETY GENERAL HAZARD WARNING: INSTRUCTIONS • Failure to comply with the precautions and instructions provided with this heater, can result READ THIS MANUAL CAREFULLY BEFORE in death, serious bodily injury and property loss INSTALLING OR SERVICING THIS PRODUCT. or damage from hazards of fire, explosion, burn, asphyxiation, carbon monoxide poisoning, and/or IMPROPER INSTALLATION, OPERATION, OR... -
Page 5: Guidelines Of Fuel Gases
GUIDELINES OF FUEL GASES: • This heater is intended for the use of temporary heating • Always maintain proper clearances from of buildings under construction, alteration or repair. combustible material. A minimum clearance of There may be other local standards or regulations 2.5meters from the heater outlet and 1.25 meters governing the use of fuel gases and heating products, from the top, sides and inlet should be observed. -
Page 6: Start-Up Operation
OPERATING INSTRUCTIONS CONTINUED... • Screw-fasten the gas hose with regulator to the left cylinder(s) and the heater must be disconnected and the cylinders removed from the heater. had thread, POL type, gas cylinder valve. Ensure the connection is gas tight. AUTOMATIC MODELS (HF30/HF50) •... -
Page 7: Specifications
SPECIFICATIONS For exact appliance specification, please refer to data plate affixed to appliance at the intake side of blow heater. HF 15 HF 20 HF 30 HF 50 Model Maximum Heat Output *54 MJ/h *72 MJ/h *108 MJ/h *170 MJ/h Gas Consumption 1.08 KG/H 1.44 KG/H... -
Page 8: Troubleshooting
TROUBLESHOOTING • The appliance is equipped with a self-fault diagnostic device. Any repair of the heater should only be carried out by a qualified technician. • Be sure the heater is disconnected from the gas cylinder before any repair work is undertaken. •... -
Page 9: Maintenance And Storage
MAINTENANCE AND STORAGE • Keep the heater clean, especially the motor grid and fan blades. This should be done seasonally or sooner if used in dirty operating conditions. • Store the heater in dry, clean and safe place, away from the reach of children. •... -
Page 10: Illustrated Parts Breakdown And Parts List
ILLUSTRATED PARTS BREAKDOWN AND PARTS LIST HF 15/20 - MANUAL MODEL Terminal block REF30/50 MANUAL MODEL SPARE PARTS SCHEDULE Solenoid valve ITEM DESCRIPTION QUANTITY M8 Nut M4 x 25 bolt Thermostat Handle Burner assembly Dished washer Nipple M4 nut Cover Motor grille Injector nozzle 6.3 x 13mm screw... - Page 11 ILLUSTRATED PARTS BREAKDOWN AND PARTS LIST...Cont... HF 30/50 - AUTOMATIC MODEL Cover REF30/50 AUTO MODEL SPARE PARTS SCHEDULE Controller Box ITEM DESCRIPTION QUANTITY Cord Grommet Motor assembly Plug & Cord Solenoid valve Handle Indicating Lamp Wheel Flame Detection Needle Terminal block Burner Assembly Rubber bush Igniting Electrode...
-
Page 12: Electrical Schematic
ELECTRICAL SCHEMATIC - MANUAL MODEL www.bromicplumbing.com... - Page 13 ELECTRICAL SCHEMATIC - AUTOMATIC MODEL www.bromicplumbing.com...