Bromic Heating TUNGSTEN SMART-HEAT PORTABLE Installation, Instruction And Service Manual
Hide thumbs
Also See for TUNGSTEN SMART-HEAT PORTABLE:
- Installation, instruction and service manual (27 pages) ,
- User manual (9 pages) ,
- User manual (8 pages)
Table of Contents
Advertisement
Quick Links
TUNGSTEN SMART-HEAT™
PORTABLE HEATER
BY BROMIC
INSTALLATION, INSTRUCTION AND
SERVICE MANUAL
SUITABLE FOR GAS RADIANT HEATER MODELS:
TUNGSTEN SMART-HEAT™ PORTABLE
WARNING
!
Do not store or use petrol or other flamable vapor
and liquids in the vicinity of this or any other
appliance.
An LP-cylinder not connected for use shall not be
stored in the vicinity of this or any other appliance.
!
WARNING: Improper installation,
adjustment, alteration, service or maintenance
can cause property damage, injury or death.
Read the installation, operating and
maintenance instructions thoroughly before
installing or servicing this equipment.
DANGER
!
If you smell gas:
1.
Shut off gas to the appliance
2.
Extinguish any open flame
3.
If odour continues, keep away from the
appliance and immediately call your gas
supplier or fire department.
!
WARNING: For Outdoor Use Only.
This appliance shall not be installed or
used indoors.
Version 1.1 EU
Advertisement
Table of Contents
Related Manuals for Bromic Heating TUNGSTEN SMART-HEAT PORTABLE
Summary of Contents for Bromic Heating TUNGSTEN SMART-HEAT PORTABLE
- Page 1 TUNGSTEN SMART-HEAT™ PORTABLE HEATER BY BROMIC INSTALLATION, INSTRUCTION AND SERVICE MANUAL SUITABLE FOR GAS RADIANT HEATER MODELS: TUNGSTEN SMART-HEAT™ PORTABLE WARNING Do not store or use petrol or other flamable vapor and liquids in the vicinity of this or any other appliance.
- Page 2 Note: Bromic Heating Pty Ltd reserves the right to make changes to specifications, parts, components and equipment without prior notification. This Installation, operation and service manual may not be reproduced in any form without prior written consent from Bromic Heating Pty Ltd.
-
Page 3: Table Of Contents
CONTENTS IMPORTANT NOTES & WARNINGS PRODUCT OVERVIEW PRODUCT DESCRIPTION SPECIFICATIONS GENERAL INFORMATION PRODUCT FEATURES INSTALLATION REQUIREMENTS GAS REQUIREMENTS INSTALLATION CLEARANCES INSTALLATION INSTRUCTIONS 9-20 HEATER INSTALLATION INSTRUCTIONS 9-19 LEAKAGE TEST OPERATING INSTRUCTIONS TURNING THE APPLIANCE ON TURNING THE APPLIANCE OFF MAINTENANCE AND SERVICING REPLACEMENT PARTS TROUBLE SHOOTING APPENDIX A... -
Page 4: Important Notes & Warnings
Replacement regulator and hose • Clothing or other flammable materials should not be hung assemblies must be purchased from Bromic Heating Pty Ltd. from the heater or placed on or near the heater. • Do not perform maintenance until heater has been turned off, •... -
Page 5: Product Overview
The heater incorporates a pivoting head and adjustable heat output for precise heat control. The heater has been designed to withstand the rigors of the outdoors. SPECIFICATIONS TUNGSTEN SMART-HEAT™ PORTABLE Model Manufactured by Bromic Heating Pty Ltd Heat Input 11.0 KW Gas Supply* LPG Cylinder (9kg or 15kg) Gas Type... -
Page 6: General Information
PRODUCT OVERVIEW CONTINUED... GENERAL INFORMATION The TUNGSTEN Gas Patio Heaters are suitable for outdoor spaces. In addition to the installation Instructions provided, the installer is to ensure that the requirements of the local authority, local gas fitting regulations, municipal building codes, and any other relevant statutory regulations are carried out. -
Page 7: Installation Requirements
INSTALLATION REQUIREMENTS IMPORTANT IMPORTANT “The tubing or the flexible hose must be changed within For use outdoors and in amply ventilated areas. An amply ventilated area must have a minimum of 25% of prescribed intervals”; the surface open area. “Use only the type of gas and the type of cylinder specified The surface area is sum of the walls surface. -
Page 8: Installation Clearances
INSTALLATION REQUIREMENTS CONTINUED... LOCATION CLEARANCES When selecting the location for the TUNGSTEN Gas Patio Heater, the following clearances should be followed. Care should be taken to ensure that the heater is not installed: • Where heat/ignition can cause damage to gas cylinders/lines •... -
Page 9: Installation Instructions
INSTALLATION INSTRUCTIONS CONTENTS PACKED IN (2) BOXES Box 1 Contents Head Assembly AAA Battery Box 2 Contents Base Assembly Front Assembly Rear Arm Assembly x 2 Side Panels x 2 Top Arms x 2 Rear Cover Top Flame Deflector Regulator www.bromicheating.com.au... - Page 10 INSTALLATION INSTRUCTIONS CONTINUED... Supplied Fasteners M8 x 95mm M8 x 40mm M8 x 16mm M5 x 8mm G8 x 8mm QTY: 4 QTY: 2 QTY: 2 QTY: 4 QTY: 16 M8 x 20mm QTY: 4 Supplied Tools M8 Hex Key Tools Not Included Phillips head screw driver and Spray Bottle www.bromicheating.com.au...
- Page 11 INSTALLATION INSTRUCTIONS CONTINUED... STEP 1: Unpack boxes and place all items on a non abrasive surface. STEP 2: Fasten rear arms to base using 2 x M8 20mm screws and the supplied M8 Hex Key. STEP 3: Position front assembly and fasten using 2 x M8 20mm screws using supplied M8 Hex Key. www.bromicheating.com.au...
- Page 12 INSTALLATION INSTRUCTIONS CONTINUED... STEP 4: Secure the rear arms to front assembly using 2 x M8 x 16mm screws and supplied M8 Hex Key. STEP 5: Secure the side panels to frame using 12 x G8 screws - A Phillips screw driver is required for this step. Repeat for opposite side.
- Page 13 INSTALLATION INSTRUCTIONS CONTINUED... STEP 6: Slide top arms over front assembly slip joints - Ensure top screw holes are faced inwards. Secure the front panel to top arms using 4 x M5 screws. ensure` rigidily and stability of the product. To engage slowly lever the two sections together using some force and push down fully STEP 7: Secure the top arms to lower arm slip joint using 2 x M8 x40 screws and supplied M8 Hex Key.
- Page 14 INSTALLATION INSTRUCTIONS CONTINUED... STEP 8: Lay both heater head and stand on a non abrasive surface as shown. Two people are required for this step. NON ABRASIVE SURFACE STEP 9: Feed gas hose through arm slot and push through until it reaches slot in bottom arm. Keep feeding hose until all slack is taken up.
- Page 15 INSTALLATION INSTRUCTIONS CONTINUED... CONTINUED... STEP 10: Secure the heater head to arms using 4 x M8 screws and supplied washers STEP 11: Return heater to upright position. Two people are required for this step. CONTINUED... NON ABRASIVE SURFACE STEP 12: Fill base with fine grain sand (this sand can be purchased from most hardware stores).
- Page 16 INSTALLATION INSTRUCTIONS CONTINUED... STEP 15: STEP 14: Place gas bottle into lower enclosure and fasten Attach regulator assembly to gas strap tightly. bottle. STEP 16: Attach hose to regulator assembly. Must be attached tightly with 2 spanners. STEP 17: Lower gas bottle bracket into position. www.bromicheating.com.au...
- Page 17 INSTALLATION INSTRUCTIONS CONTINUED... STEP 18: Secure deflector to heater by loosening the two screws and secure brackets underneath washers. Re-tighten screws to original position using screw driver. INSTALLATION INSTRUCTIONS CONTINUED... STEP 19: Unscrew igniter cap. Insert supplied AAA battery into cap and re-scew to original position STEP 20: Perform Gas leakage test as shown on page 20 www.bromicheating.com.au...
- Page 18 INSTALLATION INSTRUCTIONS CONTINUED... CONTINUED... STEP 21: Secure the top piece of rear cover to frame using 4 x G8 screws - A Phillips screw driver is required for this step. The bottom piece of rear cover is secured by magnets. Firstly position slots in back cover over the two hooks then lower cover to allow magnets to catch www.bromicheating.com.au...
- Page 19 INSTALLATION INSTRUCTIONS CONTINUED... CONTINUED... Adjusting the heater head angle CAUTION: ONLY ADJUST THE HEATER HEAD ANGLE PRIOR TO OPERATION. ADJUSTING WHILST UNIT IS IN OPERATION OR POST OPERATION CAN CAUSE SERIOUS BURNS High Head Tilt Position To set heater head angle at high position, manually push heater head up to align hole then insert slip pin.
-
Page 20: Leakage Test
INSTALLATION INSTRUCTIONS CONTINUED... LEAK TEST Gas connections on heater are leak tested at the factory prior to shipment. A complete gas leak test must also be performed after assembly before operating the heater due to possible damage occurring during transportation. •... -
Page 21: Operating Instructions
OPERATION INSTRUCTIONS TURNING THE APPLIANCE ON WARNING Do not turn the heater on with people standing in front of heater. Heater must be turned on while standing behind the heater. 1. Ensure that installation has been carried out in accordance with the manufacturers instructions outlined in this document. -
Page 22: Maintenance And Servicing
Inspect and clean at least every six months or 10. Replacement parts can be purchased to restore the more frequently in adverse conditions. heater to its original appearance from Bromic Heating Never obstruct the flow of combustion and ventilation Pty Ltd. -
Page 23: Replacement Parts
REPLACEMENT PARTS An authorised service technician MUST replace any faulty items with the correct approved component from the list below. Contact your place of purchase to organise any of the replacements parts below. Description Part No: Control Knob BH8280002 Gas Valve BH8280003 Ignition Pack BH8280004... -
Page 24: Troubleshooting
TROUBLESHOOTING What ONLY an What you can do Problem Possible cause authorised service (if these do not work, contact an authorised technician) technician can do Burner will not • Gas valve may be OFF • Turn the gas valve ON •... -
Page 25: Appendix A
APPENDIX A www.bromicheating.com.au... -
Page 26: Appendix A
APPENDIX A CONTINUED... www.bromicheating.com.au...