Oki C911 Maintenance Manual page 159

Oki Data CONFIDENTIAL
(1) Menu option display switching
LEVEL1
Use the MENU
Use OK to display the option shown in a non-shaded area ( XXXXX ), and use the MENU
Press OK to execute a test, and BACK to end the test.
[MENU∧] [MENU∧]
SWITCH SCAN MOTOR TEST
CLUTCH TEST PRINT
IN1 IN2 IN3 FIN
[MENU∨] S1-ID MOTOR [MENU∨] PRINT
EX1 EX2 EX3
EXECUTE
STFD_FU S2-ID MOTOR
TEST
T1 PE_PNE_LIFT S3-ID MOTOR
PATTERN
MPT PE_PNE_LIFT S4-ID MOTOR
TEST
S5-ID MOTOR
PU DUPSNS F
CASSETTE*1
BELT MOTOR
DUPSNS I_R_F_B
PAGE
T1 CASETTE SIZE FUSER MOTOR
STATION
CVO SI_FR_TC FUSER MTR REV
MEDIA
CVO EX_DUP_FU_ FUSER RLS
OUTPUT
MPT
JOB OFFSET
BIN
LATCH FR_EX_TC T1 LIFT UP MO-
DUPLEX*1
TOR
ID UP/DOWN
JOB
T1 HOPPING MO-
TONER SENS
OFFSET
TOR
HT THERMISTER
*1: TRAY2, TRAY3, TRAY4
REGIST MOTOR
HUM_TEMP_
and DUPLEX are displayed
LVPS_BELT FEED MOTOR
only when installed.
DEN L_K_COL/R_ MPT LIFT UP MO-
K_COL TOR
MPT MOTOR
THICK MPT_PW
T1LIFT TONER SUPPLY S1
F-RL JOFF EXO
TONER SUPPLY S2 T3 LIFT_UP
REGS
MOTOR
TONER SUPPLY S3
BF TAG
T3 HOPPING
TONER SUPPLY S4
MOTOR
TC TAG
TONER SUPPLY S5
T3 FEED CLUTCH
ID TAG
ID UP/DOWN S1
T4 LIFT_UP
SP TAG
ID UP/DOWN S2
MOTOR
DISTNR FULL_
ID UP/DOWN S3
SPRL_BOX T4 HOPPING
ID UP/DOWN S4
MOTOR
TR2POS S0-DUCT
ID UP/DOWN S5
T4 FEED CLUTCH
T2 PE_PNE_CVO
ID UP/DOWN S-
T5 LIFT_UP
T2 LF_FED
ALL
MOTOR
T2 CASETTE SIZE
TR2 POS ADJUST
T5 HOPPING
T3 PE_PNE_CVO
FACEDOWN
MOTOR
T3 LF_FED
SOLENOID
T5 FEED CLUTCH
T3 CASETTE SIZE
REGIST SHUTTER
DUPLEX
T4 PE_PNE_CVO
LV FAN
SOLENOID
T4 LF_FED
FUSER FAN1
2PASS SOLENOID
T4 CASETTE SIZE FUSER FAN2
DUPLEX ENTRY
T5 PE_PNE_CVO FUSER FAN3
MOTOR
T5 LF_FED S1/5 FAN
DUPLEX FEED
T5 CASETTE SIZE
S2/3/4 FAN
MOTOR
ID MOTOR FAN
2PASS FEED
TR2 FAN
MOTOR
T2 LIFT_UP
DUPLEX REG
MOTOR
CLUTCH
T2 HOPPING
DUPLEX FAN
MOTOR
Note:
T2 FEED CLUTCH
The motor keeps running if holding down the ENTER button
for two sec. to determine the choice. If the operation is
canceled, press CANCEL.
45530603TH Rev.2
or MENU button to select the option shown in a shaded area ( XXXXX ), and press OK to execute the option.
[MENU∨]
DIAGNOSITC MODE XX. XX. XX ○ -MODE
[MENU∧]
[MENU∧]
[MENU∧]
[MENU∧]
REG DENS MEDIA WT
ADJUST ADJUST ADJUST
TEST TEST PA
[MENU∨]
[MENU∨] [MENU∨]
REG ADJ DENS ADJ EDIT
EXECUTE EXECUTE THICKNESS
DATA
REG ADJ DENS ADJ
RESULT PAR-SET WEIGHT
SCAN
WRT POS DENS ADJ
ADJ EXEC
ADJ EXE RESULT
WEIGHT
WRT POS AUTO
SCAN
ADJ RSLT CALIBRATION
ADJ RSLT
or MENU button to select the option. The menu goes back to the top by pressing BACK.
[MENU∧] [MENU∧] [MENU∧]
PAPER CONSUMABLE PRINTER
WIDTH STATUS STATUS
SNS ADJ
[MENU∨] S1-ID UNIT S1-
[MENU∨] [MENU∨]
WIDTH IMPRESSIONS
S2-ID UNIT
ADJ PAR-
S2-
S3-ID UNIT
SET
IMPRESSIONS
S4-ID UNIT
WIDTH
S3-
S5-ID UNIT
SNS ADJ
IMPRESSIONS
S1-ID USED
EXE
S4-
S2-ID USED
WIDTH
IMPRESSIONS
S3-ID USED
SNS ADJ
S5-
S4-ID USED
RSLT
IMPRESSIONS
S5-ID USED
TOTAL
FUSER UNIT
SHEET CNT
FUSER USED
TR BELT UNIT
TR BELT USED
S1-TONER (FULL)
S2-TONER (FULL)
S3-TONER (FULL)
S4-TONER (FULL)
S5-TONER (FULL)
S1 OVER RIDE
CNT
S2 OVER RIDE
CNT
S3 OVER RIDE
CNT
S4 OVER RIDE
CNT
S5 OVER RIDE
CNT
[MENU∨]
[MENU∧]
[MENU∧]
[MENU∧] [MENU∧]
[MENU∧]
FACTORY SENSOR LED
MODE SETTING HEAD
DATA
SET
TONER [MENU∨]
[MENU∨] [MENU∨]
[MENU∨]
FACTORY SENSOR S1
S2
DISPOSAL
MODE SET
TNR SNS S3
BELT UNIT S4
CHECK
S5
ID UNIT
CHECK
REG
ADJUST
ERROR
DRUM
OVER LIFE
WR POINT
REV
Note:
[ENTER]button held down
(3seconds) when parameter
is decided.
5. MAINTENANCE MENUS
[MENU∧] [MENU∧]
DRUM FUSER ERROR
CODE
MANUAL
CLEANING
ERROR
CLEAR
[MENU∨] [MENU∨]
CODE
DRUM
MANUAL P1
CLEANING
ERROR
CODE
P2
ERROR
CODE
P3
5-18