Related Manuals for Black Horse Model Macchi MC-200 BH 104
Summary of Contents for Black Horse Model Macchi MC-200 BH 104
- Page 1 Instruction Manual book ITEM CODE: BH 104. SPECIFICATION Wingspan : 2,000mm 78.74 in. Length 1,500mm 59.06in. Weight 5,6kg 12.32 Lbs. Engine 30cc gas Radio 06 channels. Servo 08 servos Made in Vietnam.
-
Page 2: Parts List
MACCHI MC-200 - Instruction Manual Item code: BH104 This instruction manual is designed to help you build a great flying aeroplane. Please read this manual thoroughly before starting assembly of your MACCHI MC-200 . Use the parts listing below to identify all parts. WARNING. -
Page 3: Safety Precaution
MACCHI MC-200 - Instruction Manual Item code: BH104 Caution: this model is not a toy! Wing warp: Hold the panel twisted If you are a beginner to this type of powered gently in the opposite model, please ask an experienced model flyer direction to the warp, and for help and support. -
Page 4: Installing The Aileron Servo
MACCHI MC-200 - Instruction Manual Item code: BH104 REPLACEMENT SMALL PARTS 3x15mm. 3x15mm. 3x15mm 1.Door mounting wheel. 15. Plastic parts for elevator pushrod. 2. Air retract main gear. 16. Plastic for tail gear. 3. Air tank. I. SERVO 4. Valve control. INSTALLING THE AILERON SERVO. - Page 5 MACCHI MC-200 - Instruction Manual Item code: BH104 2 x 10mm 3) Using the thread as a guide and using masking tape, tape the servo lead to the end Secure of the thread: carefully pull the thread out. When you have pulled the servo lead out, re- move the masking tape and the servo lead from the thread.
-
Page 6: Installing The Aileron Linkages
MACCHI MC-200 - Instruction Manual Item code: BH104 3.INSTALLING THE AILERON LINKAGES. Installing the aileron linkages as pictures below. Thread 70 mm 2x8 mm. Electric wire Secure Secure Repeat the procedure for the other wing half. II. FLAP. 2x10mm. 1.INSTALLING THE FLAP SERVOS. Secure Flap... - Page 7 MACCHI MC-200 - Instruction Manual Item code: BH104 2. INSTALLING THE FLAP CONTROL HORN. 3mm x 15mm. C/A glue C/A glue Control horn of the flap C/A glue INSTALLING THE FLAP LINKAGES. Installing the aileron linkages as pictures below. C/A glue 55 mm 2x8mm.
- Page 8 MACCHI MC-200 - Instruction Manual Item code: BH104 Secure Repeat the procedure for the other wing half. INSTALLING AIR RETRACTABLE LANDING GEAR. 3x15mm Secure.
- Page 9 MACCHI MC-200 - Instruction Manual Item code: BH104...
- Page 10 MACCHI MC-200 - Instruction Manual Item code: BH104 Secure 5 x 45mm...
- Page 11 MACCHI MC-200 - Instruction Manual Item code: BH104 Drill a hole 3.5mm diameter Lock nut 3 x 10 mm Secure Drill a hole 3.5mm diameter Secure...
-
Page 12: Installing The Engine Mount
MACCHI MC-200 - Instruction Manual Item code: BH104 INSTALLING THE ENGINE MOUNT. Lock. See pictures below: Lock. Drill a hole Lock. 5mm diameter INSTALLING THE ENGINE- Bottom side secure. Repeat the procedure for the other wing half. -
Page 13: Installing The Throttle - Cable
MACCHI MC-200 - Instruction Manual Item code: BH104 Mount ply of wood . C/A glue 3x12mm Secure Tie wrap. Secure Battery INSTALLING THE THROTTLE - CABLE. 1. Install one adjustable metal connector through the third hole out from the center of one servo arm, enlarge the hole in the servo arm using a 2mm drill bit to accommodate the servo connector. -
Page 14: Installing The Stopper Assembly
MACCHI MC-200 - Instruction Manual Item code: BH104 FUEL TANK. Throttle cable. INSTALLING THE STOPPER ASSEMBLY 1) The stopper has been pre-assembled at the factory. 2) Using a modeling knife, cut one length of silicon fuel line (the length of silicon fuel line is calculated by how the weighted clunk should rest about 8mm away from the rear of the tank and move freely inside the tank). - Page 15 MACCHI MC-200 - Instruction Manual Item code: BH104 (Silicon tube not included) Silicon tube. Secure Fuel pick- up tube Vent tube Fuel fill tube 5) Test fit the stopper assembly into the tank. It may be necessary to remove some of the flashing around the tank opening using a modeling knife.
- Page 16 MACCHI MC-200 - Instruction Manual Item code: BH104 Left side. COWLING. 1. Slide the fiberglass cowl over the en- gine and line up the back edge of the cowl with the marks you made on the fuselage. Top side Slide the cowl back over the engine and secure it in place using four wood screws.
-
Page 17: Elevator Installation
MACCHI MC-200 - Instruction Manual Item code: BH104 3 x 12mm Secure Machine screw. Left side Secure ELEVATOR INSTALLATION. SERVO INSTALLATION. 1. Install the rubber grommets and brass collets into the elevator servo. Test fit the servo into the servo tray. 2. -
Page 18: Horizontal Stabilizer
MACCHI MC-200 - Instruction Manual Item code: BH104 HORIZONTAL STABILIZER. See pictures below: 3 x15mm Left side. 3 x15mm Secure. 208 mm Secure... - Page 19 MACCHI MC-200 - Instruction Manual Item code: BH104 ELEVATOR CONTROL HORN AND ELEVATOR PUSHROD INSTALLATION. Secure 3 x 20 mm. Plastic parts of elevator pushrod. Cut. Elevator control horn. 2 x10mm. C/A glue. Bottom side Secure. Elevator Elevator pushrod pushrod 2 x 8 mm.
-
Page 20: Vertical Installation
MACCHI MC-200 - Instruction Manual Item code: BH104 VERTICAL INSTALLATION. Rudder servo install as same as method of elevator servo. See picture below: Rudder servo MOUNTING THE TAIL WHEEL BRACKET. 1. Set the tail wheel assembly in place on the plywood plate. The pivot point of the tail wheel wire should be even with the rud- der hinge line and the tail wheel bracket should be centered on the plywood plate. - Page 21 MACCHI MC-200 - Instruction Manual Item code: BH104 Epoxy glue Elevator pushrod C/A glue.
- Page 22 MACCHI MC-200 - Instruction Manual Item code: BH104 Secure Plastic part for pushrod. Secure C/A glue. 2 x10mm.
- Page 23 MACCHI MC-200 - Instruction Manual Item code: BH104 Plastic parts for tail gear C/A glue Remove covering INSTALLATION SERVO AIR RETRACT- ABLE LANDING GEAR . Air tank Valve control conector Valve one way C/A glue...
- Page 24 MACCHI MC-200 - Instruction Manual Item code: BH104 INSTALLING SERVO USING FOR VALVE CONTROL Secure. Secure. 3 way Valve one way conector 4 w a y conector...
-
Page 25: Installing The Receiver And Battery
MACCHI MC-200 - Instruction Manual Item code: BH104 3 way conector Air tank Air supply Valve one way Nose gear 4 way conector 4 way conector Left main Switch of gear wing Right main receiver. gear wing INSTALLING THE RECEIVER AND BATTERY. 1. -
Page 26: Wing Attachment
MACCHI MC-200 - Instruction Manual Item code: BH104 WING ATTACHMENT. Drill a hole Locate the aluminium wing dihedral brace. 3mm diameter 860mm *** Test fit the aluminium tube dihedral brace into each wing haft. The brace should slide in easily. If not, use 220 grit sand around the edges and ends of the brace until it fits prop- erly. - Page 27 MACCHI MC-200 - Instruction Manual Item code: BH104 Drill a hole BALANCING. 3mm diameter 1) It is critical that your airplane be bal- anced correctly. Improper balance will cause your plane to lose control and crash. THE CENTER OF GRAVITY IS LOCATED 91MM BACK FROM THE LEADING EDGE OF THE WING.
-
Page 28: Pre-Flight Check
MACCHI MC-200 - Instruction Manual Item code: BH104 1) We highly recommend setting up a plane using the control throws listed. 2) The control throws should be meas- ured at the widest point of each control sur- face. 3) Check to be sure the control surfaces move in the correct directions.