Roland INTEGRA-7 Owners & Installation Manual page 57

Problem Items to check
Delay time does not
Could the system setting "USB Song Sync Mode" have been set
change when you change
to "SLAVE"?
the tempo
When the Legato Switch (p. 32) is "ON" and Legato Retrigger is
"OFF, " and you hold down a low note and play a high note to
produce a legato effect, the pitch might stop at a certain point
Pitch sometimes fails to rise
and fail to rise as far as you expect because the upper limit of
when playing legato
the wave data has been exceeded.
If the tone uses multiple waves, and each of these waves has a
different upper limit, the result might no longer sound mono.
Problems with the Synthesizer effects
Could the effect switch be off?
Effect not applied
Check the send level to each effect.
You specified a delay time
value (for example for multi
effect DELAY) as a note
Check the delay time setting.
value, but there's a limit
beyond which the delay
time will not change
Problems with external MIDI devices
No sound from an external Does the INTEGRA-7's MIDI transmit channel match the
MIDI device connected device's MIDI receive channel?
Could Rx Exclusive be turned "OFF"?
Exclusive messages are not
Does the transmitting unit's Device ID number match the
received
INTEGRA-7's Device ID number?
Problems with an external device you're recording
The volume level of the Could you be using a connection cable that contains a resistor? Use a connection cable that does not contain a resistor.
instrument connected to
Is the volume of the external device adjusted correctly?
INPUT jacks (Front, Rear) is
too low.
Did you adjust the Level of Ext Part?
Problems with the USB flash drive
USB flash drive is not
Check the format of the USB flash drive.
recognized
Could a strong physical shock have been applied to the USB
flash drive?
Data on the USB flash drive
was damaged
Could the unit have been turned off while accessing the USB
flash drive?
Is there sufficient free space on the USB flash drive?
Can't back up to USB flash
Check the format of the USB flash drive. The INTEGRA-7 can use
drive
USB flash drive that are formatted in FAT format.
Problems with a USB connection
The INTEGRA-7 is not
recognized by your
Does your computer's USB port support USB 2.0 Hi-Speed?
computer
Action
If "Sync Mode" is set to "SLAVE, " change the tempo of the external
device that is transmitting MIDI clock data.
If you want to make large changes in the pitch, you should turn
Legato Retrigger "ON. "
For details on the parameters, refer to "Parameter Guide PDF. "
Check the on/off setting of each effect.
The effect won't be obtained if the send level to that effect is set
at 0. Even if the send levels to the effect is set above 0, the effect
won't be applied if the multi-effect level, or reverb level are set to
0. Check each of these settings.
Increase the System tempo.
Since the delay time has an upper limit, specifying the delay time
as a note value and then slowing down the tempo may reach this
upper limit. The maximum delay time is the highest value that can
be specified numerically (i.e., other than in terms of a note value).
Match the INTEGRA-7's transmit channel and your connected
device's receive channel.
Turn Rx Exclusive "ON. "
Set the Device ID numbers.
Adjust the volume of your external device to an appropriate level.
Adjust Level of Ext Part.
Format the USB flash drive on the INTEGRA-7.
The INTEGRA-7 can use a USB flash drive that's formatted as FAT.
(Normally, a USB flash drive will be formatted as FAT when you
purchase it, so you can use it as is.) USB flash drives with a format
other than FAT (such as NTFS) will not be recognized by the
INTEGRA-7.
Format the USB flash drive on the INTEGRA-7.
Use an USB flash drive that has sufficient free space.
Format the USB flash drive on the INTEGRA-7.
The USB port of the computer connected to the INTEGRA-7 must
support USB 2.0 Hi-Speed.
Troubleshooting
Page
p. 48
p. 39
p. 36, p. 41
p. 36
p. 48
p. 32
p. 49
p. 49
p. 23
–
p. 33
p. 50
p. 50
–
p. 50
–
57