Viewing The System Version - Roland INTEGRA-7 Owners & Installation Manual

MIDI Settings (MIDI)
Parameter Value Explanation
When transmitting and receiving system
Device ID
17–32 exclusive messages, the device ID numbers of
both devices must match.
Specifies the MIDI receive channel on which
MIDI messages (program change/bank select)
from an external MIDI device will be received
Studio Set
by the INTEGRA-7 to switch studio sets.
Control
1–16, OFF
Channel
Choose "OFF" setting if you don't want studio
sets to be switched from a connected MIDI
device.
Specifies whether MIDI messages received via
the USB COMPUTER port/MIDI IN connector
USB-MIDI
OFF, ON will be re-transmitted from the MIDI OUT
Thru
connector/USB COMPUTER port (ON) or not
be re-transmitted (OFF) (p. 45).
When you edit tone or studio set settings,
this specifies whether your edits will be
Tx Edit Data OFF, ON
transmitted as system exclusive messages
(ON) or not be transmitted (OFF).
Rx Program
Specifies whether program change messages
OFF, ON
Change will be received (ON) or not be received (OFF).
Rx Bank Specifies whether bank select messages will
OFF, ON
Select
be received (ON) or not be received (OFF).
Specifies whether system exclusive messages
Rx Exclusive OFF, ON
will be received (ON) or not be received (OFF).
Rx GM Specifies whether GM System On messages
OFF, ON
System On will be received (ON) or not be received (OFF).
Rx GM2 Specifies whether GM2 System On messages
OFF, ON
System On will be received (ON) or not be received (OFF).
Specifies whether GS Reset messages will be
Rx GS Reset OFF, ON
received (ON) or not be received (OFF).
Motional Surround Settings (MOTIONAL SURROUND)
Parameter Value Explanation
Specifies whether the two-channel surround
2CH Out SPEAKER, output will be processed appropriately for
Mode PHONES listening through speakers (SPEAKER) or
headphones (PHONES).
5.1CH Specifies whether sound will (ON) or will not
Center SP OFF, ON (OFF) be output from the front center speaker
Switch
of a 5.1 channel speaker system.
5.1CH Sub Specifies whether sound will (ON) or will not
Woofer OFF, ON (OFF) be output from the subwoofer of a 5.1
(LFE) Switch
channel speaker system.
Preview Settings (PREVIEW)
Parameter Value Explanation
SINGLE: The notes specified by Preview 1–4
Note Number will be sounded one at a time,
consecutively.
SINGLE,
CHORD: The notes specified by Preview 1–4
Preview
CHORD,
Mode Note Number will be sounded simultaneously.
PHRASE
PHRASE: The phrase provided for the
corresponding patch type (category) will be
played.
Specify the pitches of the four notes that will
be sounded if you set the Preview Mode to
Preview
"SINGLE" or "CHORD. "
1–4 Note C-1–G9
Number
* These settings are ignored if Preview Mode
Specify the velocities of the four notes that
will be sounded if you set the Preview Mode
Preview 1–4
to "SINGLE" or "CHORD. "
OFF, 1–127
Velocity
* These settings are ignored if Preview Mode
Control Function Settings (CONTROL)
Parameter Value Explanation
Specify the MIDI messages that will be used as
system controls.
System Control settings allow you to specify
MIDI messages that will apply in common to
OFF,
the entire INTEGRA-7, and can be used for
CC01–31,
controlling volume, tone, etc.
System
33–95,
Control You can assign up to four MIDI messages for
PITCH BEND,
Src1–4
this type of control.
AFTER-
If you want to make assignments for realtime
TOUCH
control of the sound and effects for each
tone independently, use "matrix control" or
"multi-effect control. "
For details, refer to the "Parameter Guide PDF. "
SYSTEM: "System Control Src 1--4" will be
Control
used for tone control.
SYSTEM,
Source
STUDIO SET
STUDIO SET: Tone Control Src 1--4 (p. 32) of the
Select
Studio Set will be used for tone control.

Viewing the System Version

Shows the INTEGRA-7's software version.
1.
In the MENU screen, choose "SYSTEM" and press the
[ENTER] button.
The SYSTEM screen will appear.
2.
Use the cursor [ ] [
tab.
Overall Settings
is set to "PHRASE. "
is set to "PHRASE. "
] buttons to select the "VERSION"
49