Convenient Functions
HDMI Control Function
When you make an HDMI connection with a TV or player compatible
with AVR-4310 and HDMI control functions, you can perform the
following operations by setting the HDMI control function of each
device.
AVR-4310 power off can be linked to the TV power
n
off step.
When you set "Output audio from amp" in the TV audio output
setup operation, you can switch the amp power on.
n
You can switch audio output devices with a TV
operation.
n
You can adjust AVR-4310 volume in the TV volume
adjustment operation.
n
You can switch AVR-4310 input source through
linkage to TV input switching.
n
When playing the player, the AVR-4310 input function
switches to the function of that player.
•
When you want to listen to TV audio by AVR-4310, connect optical
digital or analog audio (vpage 15 "Connecting the Monitor").
•
When using these functions set as follows: "HDMI Control" –
"Control" (vpage 37) set to "ON".
NOTE
•
When "Control" is set to "ON", it consumes more standby power.
•
The HDMI control function controls operations of a TV that is
compatible with the HDMI control function. Make sure that the TV
and HDMI are connected when you perform HDMI control.
•
When you power off AVR-4310, the HDMI control function does not
operate. Either power on or set to standby.
•
Some functions may not operate depending on the connected TV
or player. Check the owner's manual of each device for details
beforehand.
•
When "Control" is set to "ON", it is not possible to assign an HDMI
terminal to "TV" at "Input Assign" (vpage 47).
1
Turn the power on for all the equipment connected
by HDMI cable.
2
Set the HDMI control function for all equipment
connected by HDMI cable.
Set "HDMI Control" – "Control" (vpage 37) to "ON".
b
Please consult the operating instructions for the connected
equipment to check the settings.
Carryout steps 1 and 2 should any of the equipment be plugged
b
out.
3
Switch the television input to the HDMI connected to
the AVR-4310.
4
Switch the AVR-4310 input to the HDMI input source
and check if the picture from the player is ok.
5
When you turn the TV's power to standby, check
that the power of the AVR-4310 and player also goes
on standby.
If the HDMI control function does not operate properly, check the
following points.
•
Is the TV or player compatible with the HDMI control function?
•
Is the AVR-4310 properly set?
•
Is the "HDMI Control" – "Control" (vpage 37) set to "ON"?
•
Is the "Power Off Control" (vpage 37) set to "ON"?
•
Is the "Control Monitor" (vpage 37) set for the monitor output
connected to television?
•
Are the HDMI control function settings of all equipment correct?
NOTE
Should any of the operations below be performed, the interlocking
function may be reset, in which case, repeat step's 1 and 2.
•
"Input Assign" – "HDMI" (vpage 47) setting has changed.
•
"Monitor Out" (vpage 36) setting is changed.
•
There is a change to the connection between the equipment and the
HDMI, or an increase in equipment.
Setting the Power to Standby After a
Certain Amount of Time
(Sleep Timer Function)
With this function, you can set the AVR-4310 so that the power is
automatically switched to standby after the set amount of time has
passed.
This is convenient for playing sources while going to sleep.
[SLEEP]
Press
and display the time you want to set.
The "
" indicator on the display lights.
•
The time switches as shown below each time
OFF
120 min
30 min
60 min
To cancel the sleep timer
n
[SLEEP]
Press
to set "OFF".
The "
" indicator on the display turns off.
•
The sleep timer setting is canceled if the AVR-4310's power is set to
standby or turned off.
•
The sleep timer function can be set separately for the different zones
(vpage 85 "Sleep Timer Function").
ENGLISH
[SLEEP]
is pressed.
90 min