Table of Contents
Advertisement
Setting items
GUI
iPod : Set the iPod screen display time when the input source is "iPod".
(Continued)
•
Always : Show display continuously.
•
30s : Show display for 30 seconds after operation.
•
10s : Show display for 10 seconds after operation.
•
OFF : Turn display off.
Tuner : Set the tuner screen display time when the input source is
"TUNER".
•
Always : Show display continuously.
•
30s : Show display for 30 seconds after operation.
•
10s : Show display for 10 seconds after operation.
•
OFF : Turn display off.
Quick Select Name
1. Use
ui
to select the name of the Quick Select setting you want to
Change the "Quick Select"
change, then press
display title to one you
2. Use
o p
to set the cursor to the character you want to change.
prefer.
3. Use
ui
to change the character, then press
•
Up to 16 characters can be input.
•
You can change the character type when you press
MENU
during character input.
•
The types of characters that can be input are as shown below.
GUpper case charactersH ABCDEFGHIJKLMNOPQRSTUVWXYZ
GLower case charactersH abcdefghijklmnopqrstuvwxyz
GSymbolsH ! # % & ' ( ) * + , - . / : ; < = " > ? @ [ \ ] (Space)
GNumbersH 0123456789
4. Repeat steps 1 ~ 3 to change the display name.
Zone Rename
ui
1. Use
to select the zone name (MAIN ZONE, ZONE2 or ZONE3) you
Change the display title of
want to change, then press
each zone to one you prefer.
2. Use
o p
to set the cursor to the character you want to change.
3. Use
ui
to change the character, then press
•
Up to 10 characters can be input.
•
You can change the character type when you press
MENU
during character input.
•
The types of characters that can be input are as shown below.
GUpper case charactersH ABCDEFGHIJKLMNOPQRSTUVWXYZ
GLower case charactersH abcdefghijklmnopqrstuvwxyz
GSymbolsH ! # % & ' ( ) * + , - . / : ; < = " > ? @ [ \ ] (Space)
GNumbersH 0123456789
4. Repeat steps 1 ~ 3 to change the display name.
Main remote control
operation buttons
Setting contents
ENTER
p
or
.
ENTER.
[SEARCH]
ENTER
p
or
.
ENTER
.
[SEARCH]
:Displaying the menu
Cancel the menu
Setting items
Trigger Out 1
When Setting for Zone (MAIN ZONE / ZONE2 / ZONE3)
n
Select
the
condition
for
Trigger out is activated through linkage to the power of the zone set to
activating Trigger Out 1 for
"ON".
the input source, surround
When Setting for Input Source
n
mode, etc.
Activate trigger out when the input source set to "ON" is selected.
See "TRIGGER OUT jacks"
(vpage
21)
for
more
information on trigger out.
When Setting for Surround Mode
n
Trigger Out 2
Activate trigger out when the surround mode set to "ON" is selected.
As with "Trigger Out 1",
select
the
condition
for
activating Trigger Out 2.
When Setting for HDMI Monitor
n
Activate trigger out when the HDMI monitor set to "ON" is selected.
or
n
When setting for "Vertical Stretch"
Activate trigger out through linkage when "Vertical Stretch" (vpage
36) is set to "ON".
•
ON : Activate trigger on this mode.
•
– – – : Do not activate trigger on this mode.
Remote ID
1 / 2 / 3 / 4
Set
when
you
operate
When changing the remote ID, also change the "MAIN", "iPod",
another DENON AV amplifier
"TUNER" and "NET/USB" modes of the main remote control unit at
with the remote control unit
the same time. Also change the sub remote control unit at the same
of the AVR-4310. Match the
time (vpage 90, 95 "Setting the Remote ID").
remote control unit you are
or
using with the remote ID of
the AVR-4310.
232C Port
Serial Control : Set when using an external controller.
Set when using an external
2Way Remote : Set when using a 2-way remote control unit.
controller or two-way remote
When using a DENON two-way remote control (RC-7000CI or RC-
control connected to the RS-
7001RCI, sold separately), set to "2Way Remote".
232C terminal.
NOTE
When setting to "2Way Remote", you can not use the RS-232C connector
as an external controller.
:Moves the cursor
:Confirm the setting
(Up/Down/Left/Right)
Making Detailed Settings (Manual Setup)
Setting contents
Valid for the zone set to "ON" with "When Setting for Zone".
Valid when the "MAIN ZONE" set to "ON" with "When Setting
for Zone" is selected, and when the input source set to "ON" with
"When Setting for Input Source" is selected.
Valid when the "MAIN ZONE" set to "ON" with "When Setting
for Zone" is selected, and when the input source set to "ON" with
"When Setting for Input Source" is selected.
:Return to previous menu
ENGLISH
See overleaf
Hide quick links:
Advertisement
Table of Contents
