Denon AVR-4310 Owner's Manual page 33

s Audyssey Auto Setup Preparations
STEP1 Preparation
Perform the following settings if adjustments, etc., are required for the speaker environment you're using.
If you do not need to perform the following settings, or have already completed them, select "Auto Setup Start" and then press
Proceed to " STEP2 ".
Change the Amplifier Assignment (Amp Assign)
The signal output from the SURR.BACK/AMP ASSIGN speaker terminal
of the AVR-4310 can be switched to match your speaker environment
(vpage 33 "Amp Assign").
1
Select "Amp Assign"
and then press
ENTER .
2
Press to select an item, and then press
ui
Normal : Outputs surround back channel audio.
: Outputs ZONE2 audio.
ZONE2
: Outputs ZONE3 audio.
ZONE3
: Outputs ZONE2 / ZONE3 monaural audio.
ZONE (MONO)
: Outputs front channel audio for bi-amp use.
Bi-Amp
: Outputs front channel audio during 2-channel
2CH
DIRECT and STEREO mode.
: Outputs front height channel audio.
Front Height
: Outputs front wide channel audio.
Front Wide
RETURN
b To cancel, press .
• When you are using surround back speakers with ZONE2/ZONE3,
set to "ZONE2" or "ZONE3".
• You can set in the same way as described in "Amp Assign" on page
33.
Main remote control
operation buttons
around items indicate the settings made upon purchase.
Set the Channels You will not Use (Channel Skip)
If you set the channels you will not use beforehand, those channels
will not be measured. Therefore, you can save an amount of time
commensurate with that which would have been taken to measure
those channels.
1
Select "Channel
Skip" and then press
ENTER .
ENTER .
2
Press ui to select a channel, press
the item, and then press
Configurable channels
n
Subwoofer : Set the subwoofer channel.
: Set the surround B channel.
Surround B
: Set the surround back channel.
Surround Back
n Settings
Measure
: Default setting. Measure the selected channel.
: Skip the selected channel and do not measure.
Skip
RETURN
b To cancel, press
When "Amp Assign" is set to "Normal", only then is "Surround Back"
displayed.
:Displaying the menu
Cancel the menu
Make the Optimal Speaker Settings, and Correct the Room Acoustics (Audyssey Auto Setup)
ENTER
.
o p to select
ENTER .
.
:Moves the cursor
:Confirm the setting
(Up/Down/Left/Right)
d Perform Audyssey Auto Setup
• Audyssey Auto Setup detects the presence of each speaker and
automatically calculates the speaker size, channel level, distance and
crossover frequency settings. In addition, acoustical distortions are
corrected within the listening area.
• When measuring begins, a test tone is output from each speaker.
• Position and connect all speakers before commencing Audyssey
Auto Setup.
STEP2 Speaker Detection
1
Select "Measure" and
then press ENTER .
q M easure the subwoofer
level
To stop measuring, select
b
"Cancel" and then press
ENTER
.
When "Subwoofer" is set to "Skip" with "Channel Skip", this
b
measurement is not taken, and the process proceeds to "w
Measure each speaker".
w M easure each speaker
Once the measurements in step q are complete, the
b
measurements in step w start automatically.
The measuring channel changes depending on the setting of
b
"Amp Assign" (vpage 29) and "Channel Skip" (vpage 29).
When an error message is displayed, check "Error Messages" for
details (vpage 31).
e C heck the speaker detection results
When measuring ends, the speaker detection results are
displayed.
Select "Next → Measurement" and press
b
" STEP3 ".
Press u to select "Retry", and when you press
b
at the main listening position starts again.
:Return to previous menu
ENGLISH
ENTER
to proceed to
ENTER
, measuring
See overleaf