Table of Contents
Advertisement
ENGLISH
Making Detailed Settings (Manual Setup)
Setting items
Dimmer
Bright : Normal display brightness.
Adjust display brightness of
Dim : Reduced display brightness.
the receiver.
Dark : Very low display brightness.
OFF : Turns the display off.
Setup Lock
OFF : Turn protection off.
Protect
settings
from
ON : Turn protection on.
inadvertent change.
•
When "Setup Lock" is set to "ON", the settings listed below can no
longer be changed. Also, "SETUP LOCKED!" is displayed if you attempt
to operate related settings.
· GUI menu operations
· RESTORER
· Audio/Video Adjust
· MultEQ XT
· Dynamic EQ
•
When canceling the setting, set "Setup Lock" to "OFF".
Maintenance Mode
NOTE
Used
when
receiving
Only use this function if so instructed by a DENON serviceperson or
maintenance from a DENON
installer.
service engineer or custom
installer.
Firmware Update
Check for Update : You can check for firmware updates. You can also
Update the firmware of the
check approximately how long it will take to complete an update.
receiver.
Start : Execute the update process.
When updating starts, the power indicator becomes red and the GUI
screen is shut down. The amount of update time which has elapsed is
displayed.
When updating is complete the power indicator becomes green and
normal status is resumed.
If updating fails, the set automatically retries, but if updating is still not
b
possible, one of the messages shown below is displayed. If the display
reads as shown below, check the settings and network environment,
then update again.
Updating failed
Login failed
Server is busy
Connection fail
Download fail
Main remote control
operation buttons
Setting contents
· Dynamic Volume
· Channel Level
· Audio Delay
· Input Mode
Display
Description
Updating failed.
Failure to log into server.
Server is busy. Wait a while then try again.
Failure connecting to server.
Downloading of the firmware has failed.
:Displaying the menu
Cancel the menu
Setting items
Add New Feature
Upgrade : Execute the upgrade process.
Display the new functions
When updating starts, the power indicator becomes red and the GUI
(payment required) which
screen is shut down. The amount of update time which has elapsed is
can
be
purchased
for
displayed.
downloading to the AVR-
When updating is complete the power indicator becomes green and
4310 and upgrade.
normal status is resumed.
When
you
purchase
a
If the upgrade is not successful, an error message identical to those in
b
new function and register
"Firmware Update" will appear on the display, check the settings and
your
user
information,
network environment, then update again.
"Registered" is displayed
Upgrade Status : A list of the additional functions provided by the Upgrade
on this menu and you can
will be displayed.
proceed with the upgrade.
When "Not Registered" is displayed on the Add New Feature screen,
you cannot upgrade.
To use the upgrade function, you should purchase an upgrade package
from the DENON website.
To purchase the package, you will need the ID number shown on this
screen.
To display the ID number on the screen, hold
down for 3 seconds or more.
Notes concerning use of "Firmware Update" and "Add New Feature"
•
In order to use these functions, you must have the correct system requirements and settings for a
broadband Internet connection.
•
Do not turn off the power until updating or upgrating is completed.
•
Even with a broadband connection to the Internet, approximately 1 hour is required for the updating/
upgrading procedure to be completed.
Once updating/upgrade starts, normal operations on the AVR-4310 cannot be performed until updating/
upgrading is completed.
Furthermore, updating/upgrading the firmware may reset the backup data for the parameters, etc., set
for the AVR-4310.
•
The following backup data may be erased after an update or upgrade.
Internet radio preset channel
•
Internet radio Recently Played data
•
Care of data in Internet radio, media server and USB memory device
•
•
In the event of an update error during update or upgrade, turn the AVR-4310's power off and then on
again. "Update Retry" appears on the display and update restarts from the point at which update failed.
If the error continues despite this, check the network environment.
•
Information regarding the "Firmware Update" function and "Add New Feature" will be announced on
the DENON web site each time related plans are defined.
•
When usable new firmware is released with "Firmware Update" or "Add New Feature", a notification
message is displayed on the GUI screen. When you do not want to be notified, set "Update Notification"
(vpage 40) and "Upgrade Notification" (vpage 40) to "OFF".
:Moves the cursor
:Confirm the setting
(Up/Down/Left/Right)
Setting contents
<p>
<STATUS>
and
See overleaf
:Return to previous menu
Hide quick links:
Advertisement
Table of Contents
