Denon AVR-4310 Owner's Manual page 42

ENGLISH
Making Detailed Settings (Manual Setup)
Setting items
2ch Direct/Stereo SW Mode : Select low range signal to be reproduced by subwoofer.
(Continued) • LFE : When the "2ch Direct/Stereo" – "Front" (vpage 37) setting is
set to "Large", the LFE signal alone is output from the subwoofer. Also,
when the "2ch Direct/Stereo" – "Front" setting is set to "Small", the
front channel low range signal is added to the LFE signal output from
the subwoofer.
• LFE+Main : The front channel low range signal is added to the LFE signal
output from the subwoofer.
This can be set when "2ch Direct/Stereo" – "Subwoofer" (vpage
37) is set to "Yes".
Crossover : Outputs at below set frequency, each speaker's bass signal
output from the subwoofer.
• 40Hz / 60Hz / 80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz /
250Hz
• This can be set when "2ch Direct/Stereo" – "Subwoofer" (vpage 37)
is set to "Yes".
• If the "2ch Direct/Stereo" – "Front" setting is "Large" and the "SW
Mode" setting is "LFE", "Full Band" is displayed and the setting cannot
be made.
Distance FL / Distance FR : Select the speaker.
• 0.00m ~ 18.00m (3.60m) / 0.0ft ~ 60.0ft (12.0ft) : Set the distance to
the speaker.
Set so that the difference between the front left speaker and front
right speaker distances is 6.0 m (20.0 ft) or less.
Level FL / Level FR : Select the speaker.
• –12.0dB ~ +12.0dB (0dB) : Adjust the level of each channel.
Auto Surround Mode ON : Memorize settings. Automatically play with the last used surround
Make setting for memorizing mode.
surround mode setting for OFF : Do not memorize settings. Surround mode does not change
each input signal type. according to input signal
• The auto surround mode function lets you store in the memory the
surround mode last used for playing the four types of input signals listed
below.
q Analog and PCM 2-channel signals
w Dolby Digital and DTS 2-channel signals
e Dolby Digital and DTS multi-channel signals
r Multi-channel signals other than Dolby Digital and DTS (PCM, DSD,
etc.)
• When playing in the PURE DIRECT, the surround mode does not change
even if the input signal is changed.

Main remote control
operation buttons
Setting contents
:Displaying the menu
Cancel the menu
Setting items
EQ Customize Audyssey Byp. L/R : Set when not using the "Audyssey Byp L/R"
Set so that unused equalizer equalizer.
settings are not displayed • Used : Use.
[MULTEQ XT]
when is • Not Used : Do not use.
pressed.
Set so that the "Audyssey Byp. L/R" settings can be made when the
Audyssey Auto Setup procedure is performed.
Equalizer settings for which Audyssey Flat : Set when not using the "Audyssey Flat" equalizer.
• Used : Use.
"Not Used" is set with the
• Not Used : Do not use.
Quick Select function cannot
be stored and called out.
Set so that the "Audyssey Flat" settings can be made when the
Audyssey Auto Setup procedure is performed.
Manual : Set when not using the "Manual" equalizer.
• Used : Use.
• Not Used : Do not use.
Making the Network Settings (Network Setup)
Make network settings.
Setting items
Network Connecting
1. Connect the LAN cable (vpage 22 "Connecting to a Home Network
Make settings for wired (LAN)").
LAN. 2. Turn on the AVR-4310 (vpage 23 "Turning the Power On").
AVR-4310 performs automatic network setup due to the DHCP
function.
When connecting to a network that has no DHCP function, perform the
setting in step 3.
3. Set the IP address at the "Network Connecting".
DHCP
IP Address
Exit
Detail
Set IP address and proxy manually
:Moves the cursor
:Confirm the setting
(Up/Down/Left/Right)
Setting contents
Default settings are underlined.
Setting contents
NETWORK CONNECTING NETWORK CONNECTING
DHCP OFF
ON IP Address 192 . 168 . 100 . 033
192.168.100.33 Subnet Mask 255 . 255 . 255 . 000
Default Gateway 000 . 000 . 000 . 000
Primary DNS 000 . 000 . 000 . 000
Secondary DNS 000 . 000 . 000 . 000
Proxy
Exit
q
Enter
Set IP address manually
:Return to previous menu
w
r e
Cancel
RETURN
See overleaf