Bass Peak Level - Pioneer VSX-D1011-G Operating Instructions Manual

BASS PEAK LEVEL

The LFE (Low Frequency Effect) channel in Dolby Digital and DTS program sources can produce heavily
concentrated ultra-low bass tones that may exceed the capabilities of your speaker system. The following steps
show you how to set the peak level for the LFE channel. If continuing from the preceding page the BASS PEAK
LEVEL should be selected.
MASTER
VOLUME
MENU TUNER EDIT
TUNE
SYSTEM
SETUP
ST
ENTER
AUDIO
TUNE
−
CHANNEL TEXT OFF
RF ATT D.ACCESS
1-5
STANDBY/ON
STANDBY
MOVIE MUSIC ENTER
MULTI JOG
MULTI JOG CONTROL
SET UP
PHONES
Follow steps 1-5 on page 82, if necessary, to get
to the starting point mentioned here.
1 BASSPEAK LEVEL should be
selected, if it isn't use the 5∞
buttons to select it. Press
ENTER.
SIGNAL PRO LOGIC Neo :6 LOUDNESS MIDNIGHT TONE DNR
AUTO DIGITAL
RF DTS ES EX
MPEG AAC
DIGITAL
STEREO
ANALOG
DSP
SB CH
ON MOVIE
AUTO
OFF MUSIC
L C R LFE
L S S R S SP A B
2 Use the 5∞ buttons to select
SETTING START or SETTING
CANCEL. Press ENTER.
SETTING START: The MASTER VOLUME is set
to MIN (– – – dB), a test tone plays back and you
make the setting (go to step 3).
PRO LOGIC LOUDNESS MIDNIGHT TONE DNR ATT
SIGNAL Neo :6
DIGITAL
AUTO
RF DTS ES EX
MPEG AAC
DIGITAL
STEREO
ANALOG
DSP
SB CH
ON MOVIE
AUTO
OFF MUSIC
L C R LFE
L S R SP A B
S S
SETTING CANCEL: This setting won't limit the
peak level of the LFE channel.
SIGNAL PRO LOGIC Neo :6 LOUDNESS MIDNIGHT TONE DNR ATT
AUTO DIGITAL
RF DTS ES EX
DIGITAL MPEG AAC
ANALOG STEREO
DSP
SB CH
ON MOVIE
AUTO
MUSIC
OFF
L C R LFE
L S R
S S SP A B
If you selected SETTING CANCEL go to step 4.
TEXT ON TOP MENU
GUIDE
1-5
ST
RETURN
+
BAND CHANNEL
MPX CLASS
STA
SIGNAL HI-BIT SB CH
RETURN SELECT HI-SAMPLING MODE BAND CLASS SELECT
TONE CONTROL
SPEAKERS TONE BASS/TREBLE
STEREO MONO
ATT dB
TUNED RF ATT
RDS EON
Hi-BIT/
SAMPLING
MULTI-ROOM
STEREO MONO
dB
TUNED RF ATT
RDS EON
Hi-BIT/
SAMPLING
MULTI-ROOM
STEREO MONO dB
TUNED RF ATT
RDS EON
Hi-BIT/
SAMPLING
MULTI-ROOM
Fine Tuning Your System
3 Use the 5∞ buttons to adjust the
test tones and specify the bass
peak level.
SIGNAL PRO LOGIC Neo :6 LOUDNESS MIDNIGHT TONE DNR
AUTO DIGITAL
RF DTS ES EX
MPEG AAC
DIGITAL
STEREO
ANALOG
DSP
SB CH
ON MOVIE
AUTO
OFF MUSIC
L C R LFE
L S S R S SP A B
If you set this level before the receiver
will have that level input but it will not appear on
this setup screen. (The screen will always open
with the level showing [– – – dB].)
1 Raise the level gradually.
2 Set the bass peak level at the point just before
the tone starts to distort.
Be careful! Test tones play back at loud
volumes . Make sure there are no infants or
small children in the room.
You can leave this setup any time by pressing
ENTER.
If the YES or PLUS setting on the subwoofer is
selected the test tone will only play back from the
subwoofer. If not, the test tone will play back
from all speakers set to LARGE except for the
subwoofer.
4 Press ENTER.
The display on the receiver will show FADE and
then RESUME while the MASTER VOLUME
returns to its original position.
5 EXIT should be selected (if it isn't
use the 5∞ buttons to select it),
press ENTER.
If you want to change a setting before pro-
ceeding
Start over from step 1.
Next, if you want, proceed to DYNAMIC RANGE
CONTROL.
STEREO MONO
ATT dB
TUNED RF ATT
RDS EON
Hi-BIT/
SAMPLING
MULTI-ROOM
89
En