35: Bass Multi - Roland V-Synth XT Owner's Manual

Effects List
Parameter Value
Mod Phase 0–180 deg
Mod Pre Delay 0–50.0 ms
Mod Feedback -98– +98%
Mod XoverLPF 500–15000 Hz,
THRU
Mod XoverHPF THRU, 50–800
Hz
Mod Level 0–127
Delay Time 0–1300 ms, note Adjusts the delay time from the
Delay Feedback -98– +98%
Hi Damp Freq 500–15000 Hz,
THRU
Delay Level 0–127

35: Bass Multi

Bass Multi provides Comp/Limiter, Overdrive or Distortion, 3-band
equalizer, and Chorus or Flanger effects connected in series. This
algorithm is a multi-effects for bass.
fig.MFX-35
L
Comp/
Overdrive/
Limiter
Distortion
R
Parameter Value
Comp Sw OFF, ON
Comp Thresh- -60–0 dB
old #1
Comp Attack 0–127
Comp Release 0–127
Comp Ratio 1.5:1, 2:1, 4:1,
100:1
Comp Gain -60– +12 dB
Distortion Sw OFF, ON
Drive Mode OD, DS
Drive 0–127
Amp Sim Sw OFF, ON
182
Description
Sets how the chorus or flanger
sound is spread.
Adjusts the delay time from the
direct sound until the chorus or
flanger sound is heard.
Adjusts the proportion of the ef-
fect sound that is fed back into
the effect. Negative (-) settings
will invert the phase.
Adjusts the cutoff frequency of
the low pass filter. (THRU: no
filter is used)
Adjusts the cutoff frequency of
the high pass filter. (THRU: no
filter is used)
Volume of the chorus or flanger
sound.
direct sound until the delay
sound is heard.
Adjusts the proportion of the de-
lay sound that is fed back into
the effect. Negative (-) settings
will invert the phase.
Adjusts the frequency above
which sound fed back to the ef-
fect will be cut.
High Damp, by attenuating the
higher frequencies first, makes
the delay sound more natural.
Volume of the delay sound.
3-Band Chorus/
EQ Flanger
Description
Turns the comp/limiter on/off.
Sets the volume level at which
the compression begins.
Sets the time after the sound vol-
ume is crossed the compressor
threshold until compression be-
gins.
Specifies the time from when the
volume drops below the com-
pressor threshold until com-
pression is no longer applied.
Sets the "source sound:output
sound" compression ratio.
Adjusts the output gain.
Selects whether to use overdrive
or distortion.
Selects whether to use overdrive
(OD) or distortion (DS).
Degree of distortion
Turns the amp simulator on/off.
Parameter Value
Amp Type SMALL,
BUILT-IN, 2-
STACK, 3-
STACK
Distortion Level 0–127
EQ Low Freq 50–4000 Hz
EQ Low Gain -15– +15 dB
EQ Mid Freq 50–20000 Hz
EQ Mid Q 0.5, 0.7, 1.0, 2.0,
4.0, 8.0
EQ Mid Gain -15– +15 dB
EQ Hi Freq 2000–20000 Hz
EQ Hi Gain -15– +15 dB
Mod Mode CHORUS,
(Chorus / FLANGER
Flanger)
Mod Rate 0.05–10.0 Hz,
note
Mod Depth 0–127
Mod Phase 0–180 deg
Mod Pre Delay 0–50.0 ms
Mod Feedback -98– +98%
Mod XoverLPF 500–15000 Hz,
THRU
Mod XoverHPF THRU, 50–800
Hz
Mod Level 0–127
Description
Type of guitar amp
SMALL: small amp
BUILT-IN: single-unit type amp
2-STACK: large double stack
amp
3-STACK: large triple stack amp
Volume of the overdrive or dis-
tortion sound.
Frequency of the low range
Gain of the low range
Frequency of the middle range
Gain of the middle range
Set a higher value for Q to nar-
row the range to be affected.
Gain of the middle range
Frequency of the high range
Gain of the high range
Selects whether to use chorus or
flanger.
Adjusts the speed of modulation
for the chorus or flanger.
Adjusts the depth of modulation
for the chorus or flanger.
Sets how the chorus or flanger
sound is spread.
Adjusts the delay time from the
direct sound until the chorus or
flanger sound is heard.
Adjusts the proportion of the ef-
fect sound that is fed back into
the effect. Negative (-) settings
will invert the phase.
Adjusts the cutoff frequency of
the low pass filter. (THRU: no
filter is used)
Adjusts the cutoff frequency of
the high pass filter. (THRU: no
filter is used)
Volume of the chorus or flanger
sound.