Korg MMT RADIAS Owner's Manual page 147

InitPhase (LFO Init Phase)
Sets the starting location of the waveform. This parame-
ter will be displayed and can be set if "Key Sync" is Tim-
bre.
☞p.125 "InitPhase (LFO Init Phase)"
only MFX
LFOSpread (LFO Spread)
Sets the phase difference between the left and right
channels.
28. St.Vibrato (Stereo Vibrato)
This effect causes the pitch of the input signal to shim-
mer. Using the AutoFade allows you to increase or de-
crease the shimmering speed.
Stereo In - Stereo Out
Left
Right
LFO LFO Shape
Dry/Wet
Sets the balance between the effect and dry sounds.
Mod Depth (Modulation Depth)
Sets the depth of LFO modulation.
TempoSync (LFO Tempo Sync)
Specifies whether the LFO cycle will be synchronized
with the tempo specified by the [TEMPO] knob or MIDI
clock.
☞p.125 "TempoSync (LFO Tempo Sync)"
LFO Freq (LFO Frequency)
Sets the LFO speed.
☞p.125 "LFO Freq (LFO Frequency)"
Sync Note (LFO Sync Note)
Sets the LFO frequency as a proportion of the tempo set
by the [TEMPO] knob. This parameter will be displayed
and can be set if "TempoSync" is On.
☞p.125 "Sync Note (LFO Sync Note)"
LFO Wave (LFO Waveform)
Selects the LFO waveform.
☞p.125 "LFO Wave (LFO Waveform)"
LFO Shape
☞p.125 "LFO Shape"
Key Sync (LFO KeySync)
Specifies whether the LFO will be reset by note-on.
☞p.125 "Key Sync (LFO KeySync)"
[000...180°]
[–180...+180°]
Dry / Wet
Vibrato
Vibrato
Dry / Wet
LFO Spread
[Dry, 99:1...1:99, Wet]
[000...127]
[Off, On]
[0.01...100.0Hz]
[8/1...1/64]
[Saw, Squ, Tri, Sin, S&H]
[–63...+63]
[Off, Timbre]
InitPhase (LFO Init Phase)
Sets the starting location of the waveform. This parame-
ter will be displayed and can be set if "Key Sync" is Tim-
bre.
☞p.125 "InitPhase (LFO Init Phase)"
LFOSpread (LFO Spread)
Sets the LFO phase difference between the left and right
channels.
29. RotarySpkr (IFX W-size)
RotarySpeaker (MFX)
This effect simulates a rotary speaker, and obtains a
more realistic sound by simulating the rotor in the low
range and the horn in the high range separately. The ef-
fect also simulates the stereo microphone settings.
If you want to use this effect as an insert effect, you
must select it for insert effect 1. In this case, you
won't be able to use insert effect 2.
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
Left
Horn
Rotary Speaker
+
Rotor
Right
Mode Switch: Rotate/Stop
Speed Switch: Slow/Fast
Manual Speed Control
Dry/Wet
Sets the balance between the effect and dry sounds.
Mode Sw (Mode Switch)
Switches between speaker rotation and stop.
Ctrl Src (Mode Sw. Ctrl. Source)
Selects the modulation source that will control "Mode
Sw."
☞p.125 "Ctrl Src (Control Source)"
Ctrl Mode (Mode Sw. Ctrl. Mode)
Specifies how the modulation source selected by
"CtrlSrc" will be switched.
When "Sw" = Toggle, the speaker rotates or stops alter-
nately each time you press the pedal.
Each time the value for the modulation source ex-
ceeds 64, the speaker rotates or stops alternately.
When "Sw" = Moment, the speaker is rotating. It stops
only when you press the pedal.
Rotation will occur when the value of the modula-
tion source is less than 64, and will stop when the
value is 64 or greater.
Effect parameters
[000...180°]
[–180...+180°]
Double Size
Dry / Wet
Mic Distance
Horn/Rotor
Mic Spread
Balance
Speaker Simulation
Dry / Wet
Mode Sw Control Sorce
Speed Sw Control Sorce
Speed Control Sorce
[Dry, 99:1...1:99, Wet]
[Rotate, Stop]
[Off, Velocity...MIDI5]
[Toggle, Moment]
141