Tape Echo - Korg MMT RADIAS Owner's Manual

LFO Freq (LFO Frequency)
Sets the LFO speed. Increasing this value will result in a
faster frequency.
LFOSpread
Sets the phase difference between the left and right
channels.
18. St.Mod Delay
(Stereo Modulation Delay)
This is a stereo modulation delay.
Stereo In - Stereo Out
Left
Delay
Feedback
Delay
Right
LFO Spread
LFO
Dry/Wet
Sets the balance between the effect and dry sounds.
TempoSync (DelayTime Tempo Sync)
☞p.132 LCR Delay "TempoSync (DelayTime Tempo
Sync)"
Time Ratio [TempoSync Off: 000.5...400.0% (OVER)
/TempoSync On: 012.5...400.0% (OVER)]
☞p.132 LCR Delay "Time Ratio"
L Delay, R Delay (L, R Delay Time)
[IFX: 000...480msec, MFX: 000...680msec, 1/64... 1/1]
☞p.132 StDelay "L Delay, R Delay (L, R Delay Time)"
Feedback
☞p.132 StDelay "Feedback"
Mod Depth
Sets the depth of LFO modulation.
LFO Freq (LFO Frequency)
Sets the LFO speed. Increasing this value will result in a
faster frequency.
LFOSpread
Sets the phase difference between the left and right
channels.
[0.01...100.0Hz]
[–180...180°]
Dry / Wet
Dry / Wet
[Dry, 99:1...1:99, Wet]
[Off, On]
[000...127]
[000...127]
[0.01...100.0Hz]
[–180...180°]

19. Tape Echo

This effect simulates a tape echo unit. The distortion and
tonal change typical of magnetic tape are also repro-
duced.
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
Left
Feedback
+
Tape
Saturation
Trim Pre Tone
High / Low Damp
Wah Flutter
Right
Dry/Wet
Sets the balance between the effect and dry sounds.
TempoSync (DelayTime Tempo Sync)
☞p.132 LCR Delay "TempoSync (DelayTime Tempo
Sync)"
Time Ratio [TempoSync Off: 000.5...400.0% (OVER)
/TempoSync On: 012.5...400.0% (OVER)]
☞p.132 LCR Delay "Time Ratio"
Tap1Delay, Tap2 Delay(Tap1, Tap2 Delay Time)
[IFX: 000...980msec, MFX: 0000...1380msec,
Sets the delay times for Tap1 and Tap2.
☞p.132 LCR Delay "L Delay, C Delay, R Delay (L, C, R
Delay Time)"
Tap1Level, Tap2 Level
Sets the Tap1 output level and Tap2 output level.
Feedback
Sets the Tap1 feedback amount.
High Damp
Sets the damping amount in the high range.
Low Damp
Sets the damping amount in the low range.
Trim
Sets the input level.
Saturatn (Saturation)
Sets the distortion amount.
Wah Freq (Wah Flutter Frequency)
Sets the frequency at which pitch variation will occur in
Hz stepsl.
Wah Depth (Wah Flutter Depth)
Sets the depth of pitch variation.
Pre Tone
Sets the tone of the input.
Effect parameters
Dry / Wet
Tape1 Level
Delay Spread
Tap2 Level
Dry / Wet
[Dry, 99:1...1:99, Wet]
[Off, On]
1/64... 1/1]
[000...127]
[000...127]
[000...100%]
[000...100%]
[000...127]
[000...127]
[0.01...100.0Hz]
[000...127]
[000...127]
135