Korg MMT RADIAS Owner's Manual page 131

Mod Src (Mod Source)
Selects the modulation source that will control the cutoff
frequency.
If you set this to LFO, the LFO will modulate the cutoff
frequency.
If you set this to Ctrl, the control source selected by "Ctrl
Src" will control the cutoff frequency.
Mod Int (Modulation Intensity)
Adjusts the depth of modulation applied by the modu-
lation source.
Response (Mod Response)
Adjusts the response of the modulation effect.
A setting of 0 produces slow response.
TempoSync (LFO Tempo Sync)
Specifies whether the LFO cycle will synchronize to the
tempo set by the [TEMPO] knob or by MIDI clock.
This parameter will be displayed and can be set if "Mod
Int" is LFO.
If this is Off, the LFO will operate at the cycle specified
by "LFO Freq."
If this is On, the LFO will synchronize to the tempo or
MIDI clock.
In the Global mode P04: MIDI page "Clock" set-
ting is Internal, the LFO will synchronize to the
tempo specified by the [TEMPO] knob. If the set-
ting is External, the LFO will synchronize to the
MIDI clock received from an external MIDI device.
LFO Freq (LFO Frequency)
Sets the LFO speed.
This parameter will be displayed and can be set if "Mod
Src" is LFO and "TempoSync" is Off.
Increasing this value will result in a faster frequency.
If this parameter is assigned to "Edit1," "Edit2," or
"Edit," the assignment will change to Sync Note if
you turn "TempoSync" on.
Sync Note (LFO Sync Note)
Sets the LFO frequency as a proportion of the tempo set
by the [TEMPO] knob.
The length of the specified value (note value) relative to
the tempo will be one cycle of the LFO. For example if
this is 1/4, one cycle will occupy one quarter note.
This parameter will be displayed and can be set if "Mod
Src" is LFO and "TempoSync" is On.
If this parameter is assigned to "Edit1," "Edit2," or
"Edit," the assignment will change to LFO Freq if
you turn "TempoSync" off.
[LFO, Ctrl] LFO Wave (LFO Waveform)
Selects the LFO waveform. This parameter will be dis-
played and can be set if "Mod Src" is LFO.
[–63...+63]
[000...127]
LFO Shape
Adjusts the shape of the LFO waveform. This parameter
[Off, On]
will be displayed and can be set if "Mod Src" is LFO.
☞p.90 "Shape"
Key Sync (LFO KeySync)
Specifies how the LFO will be reset at note-on. This pa-
rameter will be displayed and can be set if "Mod Src" is
LFO.
With Off, the LFO phase will not be reset when note-on
occurs.
With Timbre, the first note-on from a condition of no
keys being pressed will reset the LFO to the phase spec-
[0.01...100.0Hz]
ified by "Init Phase," and modulation will be applied at
that phase even if subsequent note-ons occur.
[8/1...1/64]
InitPhase (LFO Init Phase)
Specifies the starting position of the waveform.
This parameter will be displayed and can be set if "Key
Sync" is Timbre.
With a setting of 0°, the waveform will start from its be-
ginning at note-on.
With a setting of 180°, the waveform will start from the
mid-point of its cycle at note-on.
Ctrl Src (Control Source)
Selects the control source. This parameter will be dis-
played and can be set if "Mod Src" is Ctrl.
The filter will be controlled by the selected source.
Source
Off
Velocity
P.Bend
M.Wheel
Saw
Squ
Sin Tri
S/H
Note on
Note on
Note all off
Explanation
Not used
Velocity
Pitch bend
Modulation wheel
Effect parameters
[Saw, Squ, Tri, Sin, S&H]
Amplitude changes irregularly
(Sample & Hold)
[–63...+63]
[Off, Timbre]
Note on
[000...180°]
[Off, Velocity...MIDI5]
125