Korg MMT RADIAS Owner's Manual page 140

Effect guide
16. St.AutoPanDly
(Stereo Auto Panning Delay)
This is a stereo delay that uses an LFO to pan the delay
sound between left and right.
Stereo In - Stereo Out
Left
Trim
Delay
Delay
Right
Trim
LFO LFO Shape
Dry/Wet
Sets the balance between the effect and dry sounds.
TempoSync (DelayTime Tempo Sync)
p.132 LCR Delay "TempoSync (DelayTime Tempo
Sync)"
Time Ratio [TempoSync Off: 000.5...400.0% (OVER)/
TempoSync On: 012.5...400.0% (OVER)]
p.132 LCR Delay "Time Ratio"
L Delay, R Delay (L, R Delay Time)
[IFX: 000...500msec, MFX: 000...700msec, 1/64... 1/1]
p.132 StDelay "L Delay, R Delay (L, R Delay Time)"
Feedback
p.132 StDelay "Feedback"
Mod Depth
Sets the depth of modulation.
TempoSync (LFO Tempo Sync)
Specifies whether the LFO cycle will be synchronized
with the tempo specified by the [TEMPO] knob or MIDI
clock.
p.125 "TempoSync (LFO Tempo Sync)"
LFO Freq (LFO Frequency)
Sets the LFO speed.
p.125 "LFO Freq (LFO Frequency)"
Sync Note (LFO Sync Note)
Sets the LFO frequency as a proportion of the tempo set
by the [TEMPO] knob. This parameter will be displayed
and can be set if "TempoSync" is On.
p.125 "Sync Note (LFO Sync Note)"
LFO Wave (LFO Waveform)
Selects the LFO waveform.
p.125 "LFO Wave (LFO Waveform)"
LFO Shape
p.125 "LFO Shape"
134
High Damp Low Damp
Pan
Feedback Depth
Pan
High Damp Low Damp
LFO Spread
[Dry, 99:1...1:99, Wet]
[000...127]
[000...127]
[0.01...100.0Hz]
[8/1...1/64]
[Saw, Squ, Tri, Sin, S&H]
[–63...+63]
Key Sync (LFO KeySync)
Specifies whether the LFO will be reset by note-on.
p.125 "Key Sync (LFO KeySync)"
InitPhase (LFO Init Phase)
Sets the starting location of the waveform. This parame-
ter will be displayed and can be set if "KeySync" is Tim-
Dry / Wet
bre.
p.125 "InitPhase (LFO Init Phase)"
LFO Spread
Sets the phase difference between the left and right
Dry / Wet
channels.
High Damp
Sets the damping amount in the high range.
Low Damp
[Off, On]
Sets the damping amount in the low range.
Trim
Sets the input level.
17. Mod Delay (Modulation Delay)
This stereo delay uses an LFO to sweep the delay time.
The pitch also varies. You will obtain a delay sound with
swell and shimmering. You can also control the delay
time using a modulation source.
Wet: Mono In - Stereo Out / Dry: Stereo In -Stereo Out
Left
+
Right
[Off, On]
Dry/Wet
Sets the balance between the effect and dry sounds.
TempoSync (DelayTime Tempo Sync)
p.132 LCR Delay "TempoSync (DelayTime Tempo
Sync)"
Time Ratio
p.132 LCR Delay "Time Ratio"
L Delay, R Delay (L, R Delay Time)
p.132 StDelay "L Delay, R Delay (L, R Delay Time)"
Feedback
Sets the feedback amount for the left channel.
Mod Depth
Sets the depth of LFO modulation.
Feedback
Delay
LFO Spread
LFO
[Dry, 99:1...1:99, Wet]
[TempoSync Off: 000.5...400.0% (OVER)
/TempoSync On: 012.5...400.0% (OVER)]
[IFX: 000...980msec, MFX: 0000...1380msec,
[Off, Timbre]
[000...180°]
[–180...+180°]
[000...100%]
[000...100%]
[000...127]
Dry / Wet
Dry / Wet
[Off, On]
1/64... 1/1]
[000...127]
[000...127]