Korg MMT RADIAS Owner's Manual page 136

Effect guide
10. St.Decimator (Stereo Decimator)
This effect creates a rough sound like a cheap sampler
by lowering the sampling frequency and data bit length.
You can also simulate noise unique to a sampler (alias-
ing).
Stereo In - Stereo Out
Left
Pre LPF
Sampling Frequency
LFO
Pre LPF
Right
Dry/Wet
Sets the balance between the effect and dry sounds.
PreLPF
Selects whether the harmonic noise caused by a decrease
in sampling frequency is generated or not.
If a sampler with a very low sampling frequency re-
ceives very high-pitched sound that could not be heard
during playback, it could generate pitch noise that is un-
related to the original sound. Set "Pre LPF" to On to pre-
vent this noise from being generated.
If you set the "Fs" to about 3kHz and set "PreLPF" to
Off, you can create a sound like a ring modulator.
HighDamp
Sets the ratio of cut of the high range.
Fs
Sets the sampling frequency.
Bit
Sets the data bit length.
If you set a smaller value for the "Bit" parameter, the
sound may be distorted. The volume level may also be
changed. Use "Output Level" to adjust the level.
Out Level (Output Level)
Sets the output level.
FsModInt (Fs Modulation Intensity)
Sets the depth of sampling frequency LFO modulation.
TempoSync (LFO Tempo Sync)
Specifies whether the LFO cycle will synchronize to the
tempo specified by the [TEMPO] knob or MIDI clock.
☞p.125 "TempoSync (LFO Tempo Sync)"
LFO Freq (LFO Frequency)
Sets the LFO speed. This parameter will be displayed
and can be set if "Mod Src" is LFO and "TempoSync" is
Off.
☞p.125 "LFO Freq (LFO Frequency)"
130
Bit High Damp Output Level
Decimator
Decimator
Bit High Damp Output Level
[Dry, 99:1...1:99, Wet]
[000...100%]
[01.0k...48.0kHz]
[04...24bit]
[000...127]
[–63...+63]
[0.01...100.0Hz]
Sync Note (LFO Sync Note)
Sets the LFO frequency as a proportion of the tempo set
by the [TEMPO] knob. This parameter will be displayed
and can be set if "TempoSync" is On.
☞p.125 "Sync Note (LFO Sync Note)"
LFO Wave (LFO Waveform)
Selects the LFO waveform.
Dry / Wet
☞p.125 "LFO Wave (LFO Waveform)"
LFO Shape
Adjusts the shape of the LFO waveform.
Dry / Wet
☞p.125 "LFO Shape"
Key Sync (LFO KeySync)
Specifies whether the LFO will be reset at note-on.
☞p.125 "Key Sync (LFO KeySync)"
[Off, On]
InitPhase (LFO Init Phase)
Specifies the starting position of the waveform. This pa-
rameter will be displayed and can be set if "KeySync" is
Timbre.
☞p.125 "InitPhase (LFO Init Phase)"
11. Reverb
This effect simulates acoustical ambience such as the re-
verberation of a hall.
MFX Hall, SmoothHall
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
Left
EQ Trim
+
EQ Trim
Right
MFX Room, BritRoom
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
Left
EQ Trim
+
EQ Trim
Right
[Off, On]
Dry/Wet
Sets the balance between the effect and dry sounds.
Type
Selects the reverb type.
The reverb types that you can select will differ depend-
ing on whether this effect is used in an insert effect or in
the master effect.
Hall
Hall-type reverb, producing the reverberation of a mid-
to large-size concert or ensemble hall.
[Saw, Squ, Tri, Sin, S&H]
Pre Delay Thru
LEQ HEQ
Reverb
Pre Delay
ERs
Pre Delay Thru
LEQ HEQ
Reverb
Pre Delay
ERs
[Dry, 99:1...1:99, Wet]
[8/1...1/64]
[–63...+63]
[Off, Timbre]
[000...180°]
Wet / Dry
Wet / Dry
Dry / Wet
ER Level
Reverb Level
ER Level
Dry / Wet
[Hall...BritRoom]