Arpeggiator; Front Panel Parameter; P14 Arpeggiator - Korg MMT RADIAS Owner's Manual

Program parameters

4. ARPEGGIATOR

These are the arpeggiator-related parameters.
The RADIAS has one arpeggiator for each pro-
gram. Arpeggiator assignments can be made from
more than one timbre, but all will have the same
operation.

Front Panel Parameter

These are the parameters you can set from the front pan-
el ARPEGGIATOR/STEP SEQUENCER section.
To edit parameters marked by "*" you must first use the
ARPEGGIATOR/STEP SEQUENCER [SELECT] button
to select ARPEGGIATOR.
ON (Step Sequencer/Arpeggiator On)  ON 
Switches the arpeggiator on/off. The button will light if
this is on.
This parameter can be set only from the front panel [ON]
button.
If this is on, the two step sequencers will also be
turned on.
LATCH*
Specifies latch operation for the arpeggiator.
On (button lit)
The arpeggiator will continue playing after you take
your hand off the keyboard.
Off (button dark)
The arpeggiator will stop playing when you take your
hand off the keyboard.
This parameter can be set only from the front panel
[LATCH] button.
TYPE* (/STEP REC)
If an arpeggiator is assigned to a timbre, this will operate
as the arpeggio type select button; the arpeggio type will
change each time you press this button.
For details on the arpeggio types, refer to p.97 "Type
(Arpeggio Type) Ü TYPE (/STEP REC) á."
SELECT
[Off, ARPEGGIATOR, STEP SEQ1, STEP SEQ2]
Assigns the arpeggiator or step sequencer to each tim-
bre.
Off
The arpeggiator and step sequencer will not be assigned
to the timbre.
ARPEGGIATOR
The arpeggiator will be applied to the timbre.
When you trigger the arpeggiator from the keyboard
etc. to make it begin operating, the timbre will be played
by the specified arpeggio pattern.
96
STEP SEQ1
Step sequencer 1 will be assigned to the timbre.
When you start the step sequencer by triggering it from
the keyboard etc., the timbre will be played by the spec-
ified sequence pattern.
STEP SEQ2
Step sequencer 2 will be assigned to the timbre.
(☞"STEP SEQ1")
If the step sequencer Link function (☞p.100 "S.Se-
qLink (Sequencer Link)") is on, the sequence pat-
terns of both step sequencers 1 and 2 will play
consecutively, regardless of whether you select
StpSeq1 or StpSeq2 here.
The arpeggiator can be triggered either via the glo-
bal MIDI channel or the MIDI channel of the tim-
bre to which the arpeggiator is assigned (☞p.103
"MIDI channels that drive the arpeggiator and
step sequencers").
[Off, On]
GATE*
Refer to p.97 "Gate Time (Gate Time Offset) Ü GATE á."
TEMPO
Specifies the playback tempo of the arpeggiator.
Refer to p.96 "Tempo Ü TEMPO á."
TAP TEMPO*(REST/TIE)
[Off, On]
Specifies the playback tempo of the arpeggiator.
Lightly press the button several times at the desired tim-
ing to set the temp.

P14 ARPEGGIATOR

P14–1: COMN (Arpeggiator Common)
These parameters apply to the entire arpeggiator.
Parameters other than "Tempo" and "KeySync" in
this page cannot be set unless the arpeggiator is as-
signed to the currently selected timbre.
1: Tempo  TEMPO 
Specifies the playback tempo of the arpeggiator.
Higher values make the tempo faster.
The "Tempo" setting has no effect if the Global
mode P03: MIDI page "Clock" (☞p.117) is set to
External.
[20.0...300.0]