–
"Motion" (default): Prioritise smooth
movement.
–
"Sharpness": Prioritise image quality.
Note
•
If you are using the KX-VC300,
"Sharpness" can only be selected after
purchasing an activation key card
(KX-VCS401) to enable sending images in
Full HD resolution (Page 108).
•
If one of the other parties is using a software
version older than 2.30 (not including 2.30),
"Motion" will be selected.
•
If "Max Resolution" is set to "HD", and
"Video Quality" is changed from
"Motion" to "Sharpness", the setting for
"Max Resolution" is automatically
changed to "Auto".
•
The value that you select here does not
influence the unit's operation when you
connect to an MCU or non-Panasonic video
conference system.
"Max Resolution": Press [Enter] and use [
[
] to select the maximum display resolution of the
main video camera and sub video camera used
during a video conference call.
–
"Full HD": Maximum resolution: 1920 ´ 1080
(This mode switches the display resolution
according to the condition of the network.)
–
"HD" (default [for KX-VC300]): Maximum
resolution: 1280 ´ 720
(This mode switches the display resolution
according to the condition of the network.)
–
"Auto" (default [for KX-VC600]): This mode
selects either "Full HD" or "HD" according to
the available bandwidth.
Note
•
Selecting "Auto" or "HD" is recommended.
•
If you are using the KX-VC300, "Auto" or
"Full HD" can only be selected after
purchasing an activation key card
(KX-VCS401) to enable sending images in
Full HD resolution (Page 108).
•
When "Full HD" is selected, if the other
party has a low bandwidth, the display
resolution may be lower than when "HD" or
"Auto" is selected.
•
When making a 3-party video conference
call, the main video camera will be
automatically set to "HD", even if you have
specified "Full HD".
•
When making a 4-party video conference
call, the main video camera and sub video
camera will be automatically set to "HD",
even if you have specified "Full HD".
•
When "Video Quality" is set to
"Sharpness", only "Full HD" and "Auto"
can be selected.
•
The value that you select here does not
influence the unit's operation when you
connect to an MCU or non-Panasonic video
conference system.
"Quality of Service": Use [
between prioritising sound or images when
bandwidth is low or the network is congested.
–
"Audio" (default): When bandwidth is low
sound quality is prioritised, and when the
network is congested sound disturbance is
reduced.
–
"Video": Even when bandwidth is low or the
network is congested, image quality is
prioritised.
Note
]
•
The value that you select here does not
influence the unit's operation when you
connect to an MCU or non-Panasonic video
conference system.
•
If one of the other parties is using a software
version older than 2.30 (not including 2.30),
"Audio" will be selected.
"Audio only mode": Use [
whether to use only audio communication
(Audio-only mode) in periods of network
congestion. When in Audio-only mode, your image
is not sent to the other party. Instead, a blue screen
is sent.
–
"ON": Communication will become audio only
if there is network congestion.
–
"OFF" (default): Communication will not
become audio only, even if there is network
congestion.
Note
•
To select "ON", "Quality of Service" must
be set to "Audio".
•
Contents cannot be shared while in Audio
only mode.
•
The value that you select here does not
influence the unit's operation when you
connect to an MCU or non-Panasonic video
conference system.
•
When one of the other parties is using a
software version older than 2.30 (not
Contacts and Settings
][
] to select
][
] to select
User Manual
89