Table of Contents
Advertisement
Contacts and Settings
–
"Local site name"
–
"IP Address" (when "Manual" is
selected for "IP Address")
–
"Subnet mask" (when "Manual" is
selected for "IP Address")
•
If you are currently entering "Local site
name", the next screen will not be
displayed even if you press [R].
"Local site name": Enter a name for the local site.
"Max. Bandwidth": Press [Enter] and use [
[
] to select the maximum allowed bandwidth to
be used (512 kbps, 768 kbps, 1.0 Mbps,
1.2 Mbps, 1.5 Mbps, 2.0 Mbps, 2.5 Mbps,
3.0 Mbps, 3.5 Mbps, 4.0 Mbps, 4.5 Mbps,
5.0 Mbps, 5.5 Mbps, 6.0 Mbps, 6.5 Mbps,
7.0 Mbps, 7.5 Mbps, 8.0 Mbps, 8.5 Mbps,
9.0 Mbps, 10.0 Mbps).
Note
•
The maximum bandwidth during a video
conference call adjusts to that of the party
that has set the lowest bandwidth for the
maximum bandwidth setting among all
participating parties.
•
You cannot select a value that is higher than
the maximum bandwidth set by the dealer.
For details, contact your dealer.
•
When you make a 3-party video conference
call, select a value of "1.0 Mbps" or higher.
Otherwise, the image quality and the sound
quality cannot be guaranteed.
•
When you make a 4-party video conference
call, select a value of "1.5 Mbps" or higher.
Otherwise, the image quality and the sound
quality cannot be guaranteed.
"Video Quality": Use [
prioritising smooth movement or image quality for
video.
–
"Motion": Prioritise smooth movement.
–
"Sharpness": Prioritise image quality.
Note
•
If you are using the KX-VC300,
"Sharpness" can only be selected after
purchasing an activation key card
(KX-VCS401) to enable sending images in
Full HD resolution (Page 108).
•
If one of the other parties is using a software
version older than 2.30 (not including 2.30),
"Motion" will be selected.
•
If "Max Resolution" is set to "HD", and
"Video Quality" is changed from
"Motion" to "Sharpness", the setting for
112
User Manual
]
][
] to select between
"Max Resolution" is automatically
changed to "Auto".
•
The value that you select here does not
influence the unit's operation when you
connect to an MCU or non-Panasonic video
conference system.
"Max Resolution": Press [Enter] and use [
[
] to select the maximum display resolution of the
main video camera and sub video camera used
during a video conference call.
–
"Full HD": Maximum resolution: 1920 ´ 1080
(This mode switches the display resolution
according to the condition of the network.)
–
"HD": Maximum resolution: 1280 ´ 720
(This mode switches the display resolution
according to the condition of the network.)
–
"Auto": This mode selects either "Full HD" or
"HD" according to the available bandwidth.
Note
•
Selecting "Auto" or "HD" is recommended.
•
If you are using the KX-VC300, "Auto" or
"Full HD" can only be selected after
purchasing an activation key card
(KX-VCS401) to enable sending images in
Full HD resolution (Page 108).
•
When "Full HD" is selected, if the other
party has a low bandwidth, the display
resolution may be lower than when "HD" or
"Auto" is selected.
•
When making a 3-party video conference
call, the main video camera will be
automatically set to "HD", even if you have
specified "Full HD".
•
When making a 4-party video conference
call, the main video camera and sub video
camera will be automatically set to "HD",
even if you have specified "Full HD".
•
When "Video Quality" is set to
"Sharpness", only "Full HD" and "Auto"
can be selected.
•
The value that you select here does not
influence the unit's operation when you
connect to an MCU or non-Panasonic video
conference system.
"IP Address": Use [
IP address information for the local site ("IP
Address", "Subnet mask", "Default Gateway")
will be obtained automatically from a DHCP server
or will be set manually.
–
"Auto": Obtain the IP address information
automatically.
][
] to select whether the
]
Advertisement
Table of Contents
