Table of Contents
Advertisement
Chapter 8 Parameters Guide
Parameter/
Explanation
Range
EXP PEDAL SW SETTNG (Expression Pedal Switch
Setting)
CTL1–4 PEDAL SETTING (CTL1–4 Pedal Setting)
Prefernc (Preference)
The patch pedal setting is used. This allows
Patch
you to use different pedal settings in each
individual patch.
The CONTROLLER screen's pedal setting
(Function, Min, Max and Src Mode) is used.
System
This applies the same pedal settings to all
patches.
Function
Off
The function is not assign to the pedals.
Ch. A/B
Switches between effect channel A and B.
Comp
Switches the COMP on and off.
OD/DS
Switches the OD/DS on and off.
Switches the PREAMP/SPEAKER on and
Preamp
off.
EQ
Switches the EQ on and off.
FX-1
Switches the FX-1 on and off.
FX-2
Switches the FX-2 on and off.
Delay
Switches the DELAY on and off.
Chorus
Switches the CHORUS on and off.
Reverb
Switches the REVERB on and off.
Pedal FX
Switches the PEDAL FX on and off.
Send/Return
Switches the SEND/RETURN on and off.
Amp Ctl
Switches the Amp Control on and off.
Tuner
Switches the TUNER on and off.
Manual
Switches the MANUAL MODE on and off.
PL
Switches the PHRASE LOOP on and off.
PL Rec/Play
Records/plays back the phrase.
PL Clear
Clears the phrase.
PL Mute/Ply
Mutes playback of the phrase.
BPM Tap
Used for tap input of the Master BPM.
Delay Tap
Used for tap input of the delay time.
Controls the Start/Stop of external MIDI
MIDI Start
devices (such as sequencers).
Controls the Play/Stop of external MIDI
MMC Play
devices (such as hard disk recorders).
Increases the patch volume level by 10
Lev +10
units.
Increases the patch volume level by 20
Lev +20
units.
Decreases the patch volume level by 10
Lev -10
units.
Decreases the patch volume level by 20
Lev -20
units.
Switches to the next higher patch number
Num Inc
in the same bank as the currently selected
patch.
Switches to the next lower patch number in
Num Dec
the same bank as the currently selected
patch.
Bank Inc
Switches to the next higher bank number.
Bank Dec
Switches to the next lower bank number.
138
Parameter/
Explanation
Range
Min (Minimum)
This sets the value for times when the
Off, On
switch is Off.
Max (Maximum)
This sets the value for times when the
Off, On
switch is On.
Src Mode (Source Mode)
This sets the behavior of the value each time the switch is operation.
The normal state is Off (minimum value),
Moment
with the switch On (maximum value) only
while the footswitch is depressed.
The setting is toggled On (maximum value)
Toggle
or Off (minimum value) with each press of
the footswitch.
Display of Parameters You Can Set with
SYS KNOB SETTING
The parameter names displayed in the Play screen (p. 25) are
abbreviated. For details about the parameter names, refer to
the chart shown below.
Display with SYS
Display at Play
KNOB SETTING
screen 1
COMP:CS:Sus
COMP CS SUS
COMP:CS:Atk
COMP CS ATK
COMP:LM:Thres
COMP LM THR
COMP:LM:Rel
COMP LM REL
COMP:MB:LoThr
COMP MB LTH
COMP:MB:HiThr
COMP MB HTH
COMP:NA:Drive
COMP NA DRV
COMP:Tone
COMP TONE
COMP:Level
COMP LEVEL
ODDS:Drive
ODDS DRIVE
ODDS:Tone
ODDS TONE
ODDS:EfectLev
ODDS E LEV
PRE:Gain
PRE GAIN
PRE:Level
PRE LEVEL
PRE:Bass
PRE BASS
PRE:Mid
PRE MID
PRE:Treble
PRE TREBL
PRE:Presnce
PRE PRES
PRE:Mic Lev
PRE M LEV
EQ:Low Cut
EQ L CUT
EQ:Low Gain
EQ LOW
EQ:Lo-MidGain
EQ L MID
EQ:Hi-MidGain
EQ H MID
EQ:High Gain
EQ HIGH
EQ:High Cut
EQ H CUT
DELAY:Time
DELAY TIME
DELAY:Feedbak
DELAY FBK
DELAY:Hi Cut
DELAY H CUT
DELAY:EfctLev
DELAY E LEV
Display at the
bottom of the
Play screen
CS SUS
CS ATK
LM THR
LM REL
MB LTH
MB HTH
NA DRV
CS TNE
CS LEV
OD DRV
OD TNE
OD ELV
PreGAN
PreLEV
PreBAS
PreMID
PreTRB
PrePRS
PreMLV
EQ LC
EQ LOW
EQ LMD
EQ HMD
EQ HI
EQ HC
DD TIM
DD FBK
DD HC
DD ELV
Advertisement
Table of Contents
