Table of Contents
Advertisement
Chapter 8 Parameters Guide
2X2 CHORUS
Frequency band division is employed to produce two different
choruses, one for low frequencies and one for higher
frequencies, for both the left and right channels (for a total of
four). This allows you to achieve a more natural chorus sound.
Parameter/
Explanation
Range
Xover f (Crossover Frequency)
This sets the frequency dividing the low-
100Hz–4.00kHz
and high-frequency ranges.
Lo Rate (Low Rate)
0–100,
Adjust the speed of the chorus effect for the
low frequency range.
BPM
–BPM
When set to BPM, the value of each parameter will be set according
to the value of the "Master BPM" (p. 122) specified for each patch.
This makes it easier to achieve effect sound settings that match the
tempo of the song.
If, due to the tempo, the time is longer than the range of allowable settings, it
is then synchronized to a period either 1/2 or 1/4 of that time.
Lo Depth (Low Depth)
Adjust the depth of the chorus effect for the
0–100
low frequency range. If you wish to use this
as a doubling effect, use a setting of 0.
Lo PreDly (Low Pre Delay)
Adjusts the delay of the effect sound in the
low-frequency range.
0.0ms–40.0ms
Extending the pre-delay will produce the
sensation of multiple sounds (doubling ef-
fect).
Lo Level (Low Level)
Adjusts the volume of the effect sound in
0–100
the low-frequency range.
Hi Rate (High Rate)
0–100,
Adjust the speed of the chorus effect for the
high frequency range.
BPM
–BPM
When set to BPM, the value of each parameter will be set according
to the value of the "Master BPM" (p. 122) specified for each patch.
This makes it easier to achieve effect sound settings that match the
tempo of the song.
If, due to the tempo, the time is longer than the range of allowable settings, it
is then synchronized to a period either 1/2 or 1/4 of that time.
Hi Depth (High Depth)
Adjust the depth of the chorus effect for the
0–100
high frequency range. If you wish to use
this as a doubling effect, use a setting of 0.
Hi PreDly (High Pre Delay)
Adjusts the delay of the effect sound in the
high-frequency range.
0.0ms–40.0ms
Extending the pre-delay will produce the
sensation of multiple sounds (doubling ef-
fect).
Hi Level (High Level)
Adjusts the volume of the effect sound in
0–100
the high-frequency range.
118
SUB DELAY
This is a delay with the maximum delay time of 1,000 ms. This
effect is useful for making the sound fatter.
Parameter/
Explanation
Range
Dly Time (Delay Time)
1ms–1000ms,
Adjusts the delay time.
BPM
–BPM
When set to BPM, the value of each parameter will be set according
to the value of the "Master BPM" (p. 122) specified for each patch.
This makes it easier to achieve effect sound settings that match the
tempo of the song.
• If, due to the tempo, the time is longer than the range of allowable
settings, it is then synchronized to a period either 1/2 or 1/4 of that time.
• If you tap [CATEGORY/ENTER], the delay time will change to match
the timing of your tapping.
Feedback
Adjusts the volume that is returned to the
input.
0–100
Higher settings will result in more delay re-
peats.
Hi-Cut (High Cut Filter)
This sets the frequency at which the high
700Hz–11.0kHz,
cut filter begins to take effect. When "Flat"
Flat
is selected, the high cut filter will have no
effect.
EffectLev (Effect Level)
0–120
Adjusts the volume of the delay sound.
DirectLev (Direct Level)
0–100
Adjusts the volume of the direct sound.
Advertisement
Table of Contents
