Lt2000 Quickset Programmer - LG LST-4600A Installation And Setup Manual

LT2000 QuickSet Programmer

Use the Zenith LT2000
QuickSet II "Clone"
Programmer to copy the
setup from a "master" LG
Integrator Box or TV then
quickly transfer the setup to
duplicate LG Integrator
Boxes or TVs -must be the
same model number as the
master LG Integrator Box or
TV.
THE CLONE HAS CONTROL OF THE TV
THE CLONE IS VERSION XX
THE TV IS VERSION XX
THE SW IS REVISION XX
CLONE CLOCK= XX:XX
TV CLOCK= XX:XX
-PRESS ANY KEY TO CONTINUE.
-DISCONNECT CLONE WHEN DONE.
Clone Controlling TV Display
The optional QuickSet II Clone Programmer (LT2000) allows custom setup and programming information to be
quickly copied from a master LG Integrator Box or TV into multiple identical LG Integrator Box or TV. Once learned
from the master, setup data is retained in the LT2000 for future use.
When using the LT2000, cloning operations will go easier if the LG Integrator Box or TV set is connected to a good
quality signal and operating with a stable picture displayed. To operate the LT2000, use the indicated keys on an
Installer's remote.
Before you begin...
• The "LG Integrator Box or TV" should be connected to a
good, stable signal from an over-the-air antenna or cable
service and turned on.
• Teaching and Learning is only possible between identical
model LG Integrator Boxes or TVs. (However, the Clone pro-
grammer can store 4 different master LG Integrator Box or
TV setups.)
WARNING: Copying a blank or incorrect memory into an LG
Integrator Box or TV will cause the LG Integrator Box or TV
to operate erratically or become inoperable.
• Use an Installer's remote to operate Learning and Teaching
menus.
• Make sure that the batteries in the Clone programmer are
fresh.
• If the batteries are removed, the Clone Clock time will be
lost.
• Decide if you want to set the time from the Clone program-
mer or copy the time to the Clone programmer; from an LG
Integrator Box or TV that has the clock set to the current
time.
• Follow the connection diagrams above to connect the Clone
to a master LG Integrator Box or TV and, after learning is
complete, to another LG Integrator Box or TV to "teach" it the
setup.
• A slow flashing green light indicates there is a problem with the communications between the LG Integrator Box
or TV and the programmer. In this case, check for a damaged cable, poor contacts, or other connection troubles.
• If the status indicator is red, the programmer batteries are low and should be replaced. Use 4 good-quality alka-
line AA batteries.
Learn from Master TV
M.P.I. Connections
Antenna
¤
QuickSet II Programmer
LT2000
(or CATV)
Clone
Ferrite Core
(TDK, ZCAT2035-0930)
CAUTION: Do not connect M.P.I. Input Port to Telecommunication
(Telephone) Network
• Setting the time and transferring it to the Clone or another
LG Integrator Box or TV is a separate procedure.
• Once a setup has been copied to another identical LG
Integrator Box or TV, that identical LG Integrator Box or TV,
with the copied setup needs to be disconnected from power
for about 5 seconds to activate the newly copied setup.
• See Troubleshooting to solve problems.
A. Set Up a Master LG Integrator Box or TV.
Using an Installer's remote, set up an "LG Integrator Box or TV"
with custom settings and features as described in the master
LG Integrator Box's or TV's operating guide.
The master LG Integrator Box or TV Setup is what you will
copy to the Clone Programmer and transfer to LG Integrator
Boxes or TVs of the same model so they will operate identical-
ly.
B. Connect Clone to Master LG Integrator
Box or TV
If there is a good connection, the "Clone has Control of TV"
message will appear. (See menu above.)
Teach to Other TV
M.P.I. Connections
Antenna
¤
QuickSet II Programmer
LT2000
(or CATV)
Clone
Ferrite Core
(TDK, ZCAT2035-0930)
47