Omron E5ZE-8 Communications Manual page 29

DeviceNet Explicit Messages Set Values and Measurement
No. Address Set value or measurement value
113 00A4 Control point 0 dead band
114 00A5 Control point 1 dead band
115 00A6 Control point 2 dead band
116 00A7 Control point 3 dead band
117 00A8 Control point 4 dead band
118 00A9 Control point 5 dead band
119 00AA Control point 6 dead band
120 00AB Control point 7 dead band
121 00B0 Control point 0 fuzzy strength
122 00B1 Control point 1 fuzzy strength
123 00B2 Control point 2 fuzzy strength
124 00B3 Control point 3 fuzzy strength
125 00B4 Control point 4 fuzzy strength
126 00B5 Control point 5 fuzzy strength
127 00B6 Control point 6 fuzzy strength
128 00B7 Control point 7 fuzzy strength
Temperature
sensor
K FF38 to 0514
(-200 to 1300)
J FF9C to 0352
(-100 to 850)
R 0000 to 06A4
(0 to 1700)
S 0000 to 06A4
(0 to 1700)
T FF38 to 0190
(-200 to 400)
E 0000 to 0258
(0 to 600)
B 0064 to 0708
(100 to 1800)
N 0000 to 0514
(0 to 1200)
L FF9C to 0352
(-100 to 850)
U FF38 to 0190
(-200 to 400)
W/Re5-26 0000 to 08FC
(0 to 2300)
Numeric data for the values in the above table is all expressed as 16 - bit
signed binary (two ' s complement for negative values)
Note 1. Numeric data cannot be modified during auto - tuning.
2. Auto - tuning cannot be executed when operation is stopped. The sequen-
tial auto - tuning function is not supported with DeviceNet communications.
3. If an instruction to stop operation is executed during auto - tuning, operation
will stop after auto - tuning is cancelled.
4. The setting ranges vary depending on the setting unit used, as shown in
the following table.
Setting unit (1)
C
FED4 to 08FC
(-300 to 2300)
FF9C to 05DC
(-100 to 1500)
0000 to 0BB8
(0 to 3000)
0000 to 0BB8
(0 to 3000)
FED4 to 02BC
(-200 to 700)
0000 to 044C
(0 to 1100)
012C to 0BB8
(300 to 3000)
0000 to 08FC
(0 to 2300)
FF9C to 05DC
(-100 to 1500)
FED4 to 02BC
(-300 to 700)
0020 to 1004
(0 to 4100)
Data setting or monitoring range
Range: FC19 to 03E7 (-999 to 999)
(See note 1.)
Unit: 1 C or F
Default: 0000 (0)
Range: 0000 to 0063 (0 to 99)
(See note 1.)
Unit: 1%
Default: 0032 (50)
Setting range
F
F830 to 32C8
(-200.0 to 1300.0)
FC18 to 2134
(-100.0 to 850.0)
0000 to 4268
(0.0 to 1700.0)
0000 to 4268
(0.0 to 1700.0)
F830 to 0FA0
(-200.0 to 400.0)
0000 to 1770
(0.0 to 600.0)
03E8 to 4650
(100.0 to 1800.0)
0000 to 32C8
(0.0 to 1300.0)
FC18 to 2134
(-100.0 to 850.0)
F830 to 0FA0
(-200.0 to 400.0)
0000 to 59D8
(0.0 to 2300.0)
Numeric
Read/write
Numeric
Read/write
Setting unit (0.1)
C
F448 to 59D8
(-300.0 to 2300.0)
FC18 to 3A98
(-100.0 to 1500.0)
0000 to 7530
(0.0 to 3000.0)
0000 to 7530
(0.0 to 3000.0)
F448 to 1B58
(-300.0 to 700.0)
0000 to 2AF8
(0.0 to 1100.0)
0BB8 to 7530
(300.0 to 3000.0)
0000 to 59D8
(0.0 to 2300.0)
FC18 to 3A98
(-100.0 to 1500.0)
F448 to 1B58
(-300.0 to 700.0)
0140 to 7D00
(32 to 3200.0)
Section 4-4
Data type
F
25