Midi Implementation - Roland Audio Canvas UA-100 User Manual

MIDI Implementation

Model UA-100G Version 1.00 '99.9
1. Receive Data
Channel Voice Messages
Note On
Status 2nd byte
9nH kkH
n = MIDI channel number: 0H-FH (ch.1-ch.16)
kk = note number : 00H-7FH (0-127)
* Used for pitch changes when using VT effect
Pitch Bend Change
Status 2nd byte
EnH llH
n = MIDI channel number: 0H-FH (ch.1-ch.16)
mm, ll = Pitch Bend value: 00 00H-40 00H-7F 7FH (-8192-0- +8191)
* Used for pitch changes when using VT effect
Control Change
You can control the main parameters for the UA-100's mixer using Control Change
messages.
* Note that the controller numbers used by the UA-100 differ from the Control
Change messages defined in the MIDI standard, and are used to control
proprietary parameters for the UA-100.
Status 2nd byte
BnH mmH
n = MIDI channel number: 0H-FH (ch. 1 to ch. 16:Refer to the correspondence chart)
mm = Mixer parameter number:Refer to the correspondence chart
ll = Mixer parameter value: 00H - 7FH (0 - 127)
Correspondences Between MIDI Channels and Mixer Signals
MIDI channel
1Ch. LINE (Line
MIC1+MIC2 (MIC1+MIC2 Mode)
2Ch. MIC2 (Mic mode only)
3Ch. WAVE1
4Ch. WAVE2
5Ch. SysRET(system effect return Main bus)
6Ch. SysSUB(system effect return Sub bus)
15Ch. WAVE (Rec)
16Ch. LINE (Master)
78
3rd byte
vvH
3rd byte
mmH
3rd byte
llH
Signal
Mode), MIC1/GUITAR (Mic
Mixer parameters and setting ranges
Parameter
MIC/LINE 21 (15H)
Selector
Pan 10 (0AH)
Send 1 16 (10H)
Send 2 17 (11H)
Mute 18 (12H)
Solo 19 (13H)
Sub Fader 20 (14H)
Main Fader 7 (07H)
Selector 22 (16H)
Effect Switch 23 (17H)
Correspondences Between Mixer Signals and Parameters
MIC1/LINE/
Parameter
MIC/LINE Selector
21 (15H)
Pan
10 (0AH)
Send 1
16 (10H)
Send 2
17 (11H)
Mute
18 (12H)
Solo
Mode),
19 (13H)
Sub Fader
20 (14H)
Main Fader
7 (07H)
Selector
22 (16H)
Effect Switch23
(17H)
Data Entry (Controller number 6, 38)
Status
BnH
BnH
n = MIDI channel number: 0H-FH (ch.1-ch.16)
mm, ll = the value of the parameter specified by RPN/NRPN
mm = MSB(upper byte of parameter), ll = LSB(lower byte of parameter)
mm ll (setting range)
0: Mic Mode, 1: Line Mode, 2: MIC1+MIC2 Mode
0 (left) - 64 (center) - 127 (right)
0 - 127: Full/Compact Effect mode only
0 - 127: Full/Compact Effect mode only
0 (OFF), 1 (ON: Mute)
0 (OFF), 1 (ON: Solo)
0 - 127
0 - 127
<Full/Compact Effect mode>
0: MIC1 (Mic Mode), LINE (Line Mode),
MIC1+MIC2 (MIC1+MIC2 Mode), 1: MIC2 (Mic
Mode only),
2: WAVE1, 3: WAVE2, 4 to 7: CH1 to 4, 8: SUB, 9:
MAIN
<VT Effect mode>
0: MIC1 (Mic Mode), LINE (Line Mode),
1: MIC2 (Mic Mode only), 2: WAVE1, 3: WAVE2,
4: VT_OUT, 5: MAIN
0 (OFF), 1 (ON: Apply effect)
MIC2 WAVE1 WAVE2 SysRET
MIC1MIC2
2Ch. 3Ch. 4Ch.
1Ch.
- - -
- -
- - - -
2nd byte 3rd byte
06H mmH
26H llH
SysSUB6 WAVE LINE
5Ch. Ch. 15Ch. 16Ch.
- - - -
- - - -
- -
- -
- - - -
- - - -
- - - -
- -
- -
- -