Tips For Recording Activities; Stopping An Activity; Evaluating An Activity; Running - Garmin D2 MACH1 Owner's Manual

3 If the activity requires GPS signals, go outside to an
area with a clear view of the sky, and wait until the
watch is ready.
The watch is ready after it establishes your heart rate,
acquires GPS signals (if required), and connects to
your wireless sensors (if required).
4 Press START to start the activity timer.
The watch records activity data only while the activity
timer is running.

Tips for Recording Activities

• Charge the watch before starting an activity
the Watch, page 60).
• Press LAP to record laps, start a new set or pose, or
advance to the next workout step.
• Press UP or DOWN to view additional data screens.
• Swipe up or down to view additional data screens.
• Hold MENU, and select Power Mode to use a power
mode to extend battery life
page 58).

Stopping an Activity

1 Press STOP.
2 Select an option:
• To resume your activity, select Resume.
• To save the activity and view the details, select
Save, press START, and select an option.
NOTE: After you save the activity, you can enter self-
evaluation data

(Evaluating an Activity,

• To suspend your activity and resume it at a later
time, select Resume Later.
• To mark a lap, select Lap.
• To navigate back to the starting point of your activity
along the path you traveled, select Back to Start >
TracBack.
NOTE: This feature is available only for activities
that use GPS.
• To navigate back to the starting point of your activity
by the most direct path, select Back to Start >
Route.
NOTE: This feature is available only for activities
that use GPS.
• To measure the difference between your heart rate
at the end of the activity and your heart rate two
minutes later, select Recovery HR, and wait while
the timer counts down.
• To discard the activity, select Discard.
NOTE: After stopping the activity, the watch saves it
automatically after 30 minutes.
Evaluating an Activity
Before you can evaluate an activity, you must enable
the self-evaluation setting on your D2 Mach 1 watch
(Activities and App Settings,
Activities and Apps
(Charging
(Customizing Power Modes,
page 7).
page 16).
NOTE: This feature is not available for all activities.
1 After you complete an activity, select Save
an Activity, page 7).
2 Select a number that corresponds with your perceived
effort.
NOTE: You can select
3 Select how you felt during the activity.
You can view evaluations in the Garmin Connect app.

Running

Going for a Track Run

Before you go for a track run, make sure you are running
on a standard-shape, 400 m track.
You can use the track run activity to record your outdoor
track data, including distance in meters and lap splits.
1 Stand on the outdoor track.
2 From the watch face, press START.
3 Select Track Run.
4 Wait while the watch locates satellites.
5 If you are running in lane 1, skip to step 11.
6 Press MENU.
7 Select the activity settings.
8 Select Lane Number.
9 Select a lane number.
10 Press BACK twice to return to the activity timer.
11 Press START.
12 Run around the track.
After you run 3 laps, your watch records the track
dimensions and calibrates your track distance.
13 After you complete your activity, press STOP, and
select Save.

Tips for Recording a Track Run

• Wait until the GPS status indicator turns green before
starting a track run.
• During your first run on an unfamiliar track, run for a
minimum of 3 laps to calibrate your track distance.
You should run slightly past your starting point to
complete the lap.
• Run each lap in the same lane.
NOTE: The default Auto Lap
laps around the track.
• If you are running in a lane other than lane 1, set the
lane number in the activity settings.

Going for a Virtual Run

You can pair your watch with a compatible third-party app
to transmit pace, heart rate, or cadence data.
1 From the watch face, press START.
2 Select Virtual Run.
3 On your tablet, laptop, or phone, open the Zwift
another virtual training app.
(Stopping
to skip the self evaluation.
distance is 1600 m, or 4
®
app or
™
7