IBM SAN192C-6 Installation, Service And User Manual page 114

<Tue Jun 25 15:12:13 2019> Standby supervisor not yet online.
This might take some time,
Please wait ...
2019 Jun 25 15:12:18 switch %SYSMGR-2-ACTIVE_LOWER_MEM_THAN_STANDBY:
Active supervisor in
slot 6 is running with less memory than standby supervisor in slot 5.
2019 Jun 25 15:12:27 switch %USBHSD-STANDBY-2-MOUNT: logflash: online
2019 Jun 25 15:12:27 switch %USBHSD-STANDBY-2-MOUNT: USB1: online
2019 Jun 25 15:12:32 switch %BOOTVAR-5-NEIGHBOR_UPDATE_AUTOCOPY:
auto-copy supported by neighbor supervisor, starting...
2019 Jun 25 15:14:05 switch %PLATFORM-1-PFM_ALERT:
Disabling ejector based shutdown on sup in slot 5
<Tue Jun 25 15:14:13 2019> Standby supervisor not yet online.
This might take some time,
Please wait ...
Note : If you see the following failure message, ignore the message, the active Supervisor-1 Module
will bring up the standby Supervisor-4 Module to the HA-standby supervisor state in some time.
Tue Jun 25 15:14:13 2019 switch %SYSMGR-2-STANDBY_BOOT_FAILED:
Standby supervisor failed to boot up.
The following message is displayed when the standby module
(Supervisor-4 Module in slot 5) is online:
2019 Jun 25 15:15:06 switch %MODULE-5-STANDBY_SUP_OK:
Supervisor 5 is standby
2019 Jun 25 15:15:07 switch %PLATFORM-1-PFM_ALERT:
Enabling ejector based shutdown on sup in slot 6
<Tue Jun 25 15:15:33 2019> Standby Supervisor-4 has come online,
configs will be copied
8. System will automatically do a copy running-config to startup-config.
The following message is displayed:
<Tue Jun 25 15:15:33 2019> Saving configuration now.
Please wait ...
[########################################] 100%
Copy complete.
/mnt/plog/migration.log: 2.78 kB 71.36 kB/s
<Tue Jun 25 15:15:46 2019> Supervisor-3 will switchover
to Supervisor-4 (DS-X97-SF4-K9) now
<Tue Jun 25 15:15:46 2019> Switchover is successful,
Supervisor-4 is now active
9. Once the standby module comes online, a system switchover happens and the new Supervisor-4
Module becomes the current active. This process moves the Supervisor-4 Module from the HA-
standby mode to active mode. The SSH/telnet session is disconnected during the switchover. You
have to reconnect to the SSH/telnet session. Also, ensure that the console link and the management
link are connected to the Supervisor-4 Module.
The following syslog message is displayed on the active Supervisor-4 Module:
Supervisor-4 Module syslogs
switch(standby) login: 2019 Jun 25 15:15:47 switch %KERN-2-SYSTEM_MSG:
[ 377.107557]
Switchover started by redundancy driver - kernel
2019 Jun 25 15:15:47 switch %SYSMGR-2-HASWITCHOVER_PRE_START:
This supervisor is becomingactive (pre-start phase).
2019 Jun 25 15:15:47 switch %SYSMGR-2-HASWITCHOVER_START:
Supervisor 5 is becoming active.
User Access Verification
switch login: 2019
Jun 25 15:15:48 switch %SYSMGR-2-SWITCHOVER_OVER:
Switchover completed.
2019 Jun 25 15:15:48 switch %ASCII-CFG-6-INFORMATION:
Reading ACFG Runtime information
2019 Jun 25 15:15:48 switch %IM-5-IM_MGMT_INTF_STATE: mgmt0 is DOWN
2019 Jun 25 15:15:48 switch %FC-REDIRECT-5-IVR_SUPPORT_ENABLED:
IVR Support Enabled in
FC_Redirect. Source: Local Switch - 20:00:84:78:ac:09:35:00
2019 Jun 25 15:15:50 switch %PLATFORM-1-PFM_ALERT:
Disabling ejector based shutdown on sup
in slot 5
2019 Jun 25 15:15:52 switch %BOOTVAR-2-SUP_MIGRATION_CONFIG_STARTED:
Setting boot parameters for supervisor migration process.
It might take some time. Please do not set
any config parameters during this time or do not replace standby.
2019 Jun 25 15:15:56 switch %IM-5-IM_MGMT_INTF_STATE: mgmt0 is UP
User Access Verification
switch login: 2019 Jun 25 15:16:39
switch %BOOTVAR-2-SUP_MIGRATION_CONFIG_COMPLETE:
88 IBM Storage Networking SAN192C-6, SAN384C-6 and SAN768C-6: SAN192C-6, SAN384C-6 and
SAN768C-6 Installation, Service, and User Guide