About The Sampling Menu - Roland Fantom-06 Reference Manual

About the SAMPLING MENU

1 .
Press the [SAMPLING] button.
The SAMPLING MENU screen appears.
Use the icons on the screen and the FUNCTION knobs
according to your objective when you perform tasks on this
unit.
Menu Explanation
This lets you sample and play back sounds
SAMPLING using the pads, including the sounds you
<To Pad> make when playing this unit or sounds
from external devices.
This lets you sample and play back sounds
SAMPLING using the keyboard, including the sounds
<To Keyboard> you make when playing this unit or sounds
from external devices.
SAMPLING This only saves samples without assigning
<To Storage> them to the pads or keyboard.
IMPORT Imports an audio file for you to play using
<To Pad> the pads.
IMPORT
Imports an audio file for you to play using
<To Keyboard>
the keyboard.
IMPORT Creates a multisample using multiple
<To Multisample> audio files.
Use this to check the status of data used
by the Kbd samples or Expansio
[E1] WAVE/EXP
as the EXZ series).
MEMORY INFO
optimize Kbd sample data that needs to be
consolidated.
[E4] PAD SAMPLE Edits the Pad samples.
[E5] KBD SAMPLE Edits the Kbd samples.
[E6] MULTISAMPLE
Edits the multisamples.
Refer to "05 Sampler: Sampling" for details on the parameters
and so forth along with the explanations that follow.
Sampling
(To Keyboard)
Read the "Sampling (To Pad)" (p. 95) section for explanations and
other information on the detailed parameters.
NOTE
Before sampling, make sure that there is enough memory
remaining. You can still record samples all the way up the maximum
length even if there is not enough memory, but the samples may
not save, depending on how much memory is left.
1 .
Connect the device (audio device or mic) you
want to sample as necessary to the MIC/LINE
INPUT jack.
MEMO
To sample an audio device in stereo, connect the left channel to L/
MONO jack, and the right channel to R jack.
2 .
Press the [SAMPLING] button.
The SAMPLING MENU screen appears.
3 .
4 .
5 .
6 .
n (such
You can also use this to
Touch SAMPLING <To Keyboard>.
The SAMPLING STANDBY (TO KBD) screen appears.
Time counter
Click on/off
Touch <Sampling Mode> to select the sampling
mode.
Set the input volume as necessary.
Configure the sampling settings.
Parameter Value
Destination
0001–
Tone
FWD
ONE-SHOT
Loop Mode
REV
REV-ONE
0 (C -1) –127
Original Key
(G 9)
Save To
Internal OFF, ON
Storage
Assign To
OFF, ON
Keyboard
Emphasis OFF, ON
Level meter
Parameter display area
Recording status
Explanation
Select the number of the user
tone that uses the wave you
sampled.
After the sample
plays back
from its start to
Start Loop
end points, it
repeatedly plays
back from its loop
start point to its
end point.
The sample plays
Start Loop
back only once
from its start to
end point.
The sample plays
back repeatedly
from its end to
Start Loop
start point (in
reverse). The loop
point is disabled
in this case even if
you have set it.
The sample plays
Start Loop
back only once
from its end to
start point (in
reverse).
Sets the note number that plays
back the sample at the same pitch
at which it was recorded.
The sampled wave is saved in WAV
format on internal storage (in the
INT:KBD_SMPL folder).
When this is "OFF", the sound is
imported as a Kbd sample, but is
not assigned to the tone of the
current zone.
When this is "ON", pre-emphasis
(which emphasizes the high end
of the sample) is applied to the
imported sound.
End
End
End
End
81 81