Roland Fantom-06 Reference Manual page 183

Problem Items to check
Problems with the sequencer
After recording, there's
Could a specific track be muted?
no sound when you
Could a specific track be soloed?
play back the pattern
The tempo is different
than when the pattern
Did you save the scene?
was played a previous
time
After playing a song on
Could the song data contain data that set the
the sequencer, there is
volume to zero?
no longer sound
The sound will be interrupted if the maximum
polyphony is exceeded.
Is there an Aftertouch or other such large
Performances are Control Change at the point where the song
sluggish, or have performance is sluggish?
interruptions
Is the data concentrated at the beginning of the
beats in the sequence data?
Problems with saving
Save the tones.
A scene sounds
different than when
you saved it
Check the effect settings.
Arpeggio and controller
settings differ between Check the arpeggio and controller settings.
studio sets
Problems with external MIDI devices
Does the MIDI transmit channel of the zone set
to EXT match the MIDI receive channel of the
connected device?
No sound from an
Is the zone that you want to output MIDI unlit, or
external MIDI device
set to EXT?
Is the zone set to EXT assigned to output MIDI?
Could Receive Exclusive be turned "OFF"?
Exclusive messages are
Does the transmitting unit's Device ID number
not received
match the FANTOM's Device ID number?
Although a tone's bend range can be set in a
When the tone's bend
range of 0–48, there are some waves for which
range is large (48), the the pitch cannot rise to the full extent of the
pitch does not rise to its pitch bend message, causing the pitch to stop
full extent when a MIDI rising at a certain point. We guarantee that the
pitch bend message is pitch will rise at least to a pitch bend range
received setting of 12, but please use caution if you
specify a bend range that is greater than this.
Action
Defeat muting.
Defeat solo.
When you change the tempo and play back, the FANTOM
does not save that tempo unless you save the scene. If you
want to keep the modified tempo, save the scene.
After playing a song that ends with a fade-out, sound might
no longer be heard. In this case it may be that a volume
message or expression message has lowered the volume.
Check each value and set it appropriately.
Try reducing the number of notes that are played.
In some cases, sustained notes with a long release might
cause processing to continue even though the notes are no
longer actually audible. In such cases, the polyphony of the
performance data differs from the number of notes that you
hear.
If the data is no longer needed, delete the data.
Try spreading the data apart so that it does not occur at the
same timing (microscope).
It is easy for data to be concentrated at the first beat of
the song if you use step recording to enter the song data,
or if you apply quantization after realtime input from the
keyboard. This causes a large amount of data to be sent to
the FANTOM in a short time, possibly causing a delay in note
processing.
If you edit the tones used by scene, or if the temporary
tones of the scene were rewritten from an external MIDI
device, you'll need to save those tones as well.
It might be that the master effect (system effect) settings
have changed.
Arpeggio and controller settings are independently saved
for each scene.
Match the zone's transmit channel with the connected
device's receive channel.
For details, refer to "Parameter Guide" (PDF).
Unless the current zone is unlit, or unless one of the zones
is set to EXT, playing the keyboard will not transmit MIDI
messages.
Unless the zone set to EXT is the current zone, or unless
the keyboard is connected via a layer that includes another
current zone, MIDI messages are not transmitted.
Turn Receive Exclusive "ON".
Set the Device ID numbers.
–
Troubleshooting
Page
p. 113
p. 114
p. 56
–
–
p. 129
p. 126
p. 64
p. 69
p. 42
–
p. 8
p. 8
p. 168
p. 167
–
183 183