Roland VersaCamm VS-640 Service Notes page 203

CUTTING MENU
PRINT-CUT ADJ.
SERVICE MENU FRSHODPULWwabC
***
SENSOR CHECK
This menu displays the real-time status of each sensor. It shows [ ] when the sensor is ON.
The first page shows the status of each sensor. Each alphabet stands for as follows.
F: Front Paper Sensor
R: Rear Paper Sensor
S: Crop Mark Sensor
H: Head Lock Sensor
O: Limit Sensor
D: Side Cover Sensor
P: Maintenance Cover Sensor
U: Head Up/Down Sensor
L: Sheet Load Sensor
SERVICE MENU THERMISTOR CHK
THERMISTOR CHK HEAD:25 C/ 77 F
SERVICE MENU
SUB MENU
SUB MENU
SERIAL NO.
SUB MENU
CHANGE INKTYPE
SUB MENU
FILL INK
SUB MENU
PUMP UP
SUB MENU
HEAD REPLACE
PRINT-CUT ADJ.
TEST PRINT
PRINT-CUT ADJ.
SETTING
PRINT-CUT ADJ.
TEST PRINT 2
12345678
H * *EC
*
W: Pinch Roller Sensor
w: Wiper Sensor
a: TU Motor Drive Sensor
(When TU is connected)
b: Chock Valve Sensor
(* is disappear when the Choke Valve is closed.)
C: Front Cover Sensor
(When the DipSW PAGE16bit1 is 1.)
This is for checking Thermistor. It displays the temperature read from the thermistor placed on the board of the Head1.
The temperature on the left is in Celsius and the right is in Fahrenheit.
Since the temperature of the device possibly rises, it normally shows higher temperature than the room temperature.
SERIAL NO.
ZS00000
CHANGE INKTYPE
MAX 4 MAX
This is for changing the Ink Type. Different from the process in the User Menu,
operations such as Head Wash and Fill Ink are not included.
This menu is used as a correction purpose when a wrong-type ink is selected.
When the ink type is changed, Ink System is initialized internally and then it exits
the menu and Setup is canceled.
EMPTY
DRAIN BOTTLE
When ink is not filled
SELECT INK TYPE
E-SOL Max4COLOR
EMPTY
DRAIN BOTTLE
SET DUMMY CRT. PUMPING-UP...
123456 >>>>>
EMPTY
DRAIN BOTTLE
Cleaning and ink filling for after head replacement.
PERFORMING
TEST PRINT
F:+0.30 +0.30mm
S:-0.40 -0.40mm
Returns to menu with [MENU] key
PERFORMING
TEST PRINT
Head Up/Down Sensor
H: Head HIGH
L: Head LOW
TU Motor Drive Sensor
* : Driving
Blank : Not driving
This menu is for entering the Serial No. of the machine in seven digits. The cursor moves
between digits with [ ] and [ ] keys. The parameter can be changed with [
NOW PROCESSING..
4
BUSY LED flashes
INSTALL SET SOL CRT.
DRAIN BOTTLE 12345678
SET CARTRIDGE
12345678
Goes next, when cartridge is set
CHECK
FILLING INK...
>>>>>
DRAIN BOTTLE
Goes next, when completed
REMOVE SOL CRT.
12345678
REMOVE CARTRIDGE
12345678
Goes next, when cartridge is removed
REMOVE DUMMY CRT
123456
Goes next, after pressing ENTER
[HEAD REPLACE]
sequence
4-5
This test pattern is for adjusting the print & cut
position. It prints three square Crop Marks along the
scan direction and cuts the contours of the marks.
When it shows [ ], it means that it has never
*****
been setup and it needs to be set. In this case, even
if adjustment is unnessesary due to the test result,
[0] must be set here.
This test pattern is for adjusting the print & cut
position. It prints 0.1mm scales for both scan and
feed direction and then cuts crosswise.
The second page shows the status of each
Cartridge Sensor and Ink Empty Sensor.
Each color has two positions and the left side
on the display shows the left-side head.
Blank: Cartridge not inserted, Ink remains
C: Cartridge inserted, Ink remains
E: Cartridge not inserted, Ink empty
* : Cartridge inserted, Ink empty
] and [ ] keys.
To Setup View
Ink Type PIG 4 : PIGMENT CMYK
Max 4 : ECO-SOL Max CMYK
Max 6 : ECO-SOL Max CMYKLcLm
Max WMT : ECO-SOL Max WMT
UNKNOWN: Ink Type not specified
PUMPING-UP...
>>>>>
Goes next, when completed
PUMPING-UP...
>>>>>
[FILL INK]
sequence