Round Spray Tips - Graco Pro Xp 60 WB Instructions Manual

AEF Fine Fine Finish Finish Pre
AEF AEF Fine Finish
Recommended for high finish quality applications at low and medium pressures. AEF tips have a pre-orifice
that assists in atomizing sheer thinning materials, including lacquers.
Order desired tip, Part Part Part No. No. AEFxxx,
Orifice Orifice Orifice Fluid Fluid Fluid Output
Size fl fl fl oz/min oz/min (l/min)
Size Size oz/min
in. (mm) in. in. (mm) (mm)
at at at 600 600 psi 600 psi psi
(4.1 MPa, MPa,
(4.1 (4.1 MPa,
41 bar) 41 41 bar) bar)
0.008 5.6 (0.17)
(0.203)
0.010
9.5 (0.28)
(0.254)
0.012 12.0
(0.305) (0.35)
0.014 16.0
(0.356) (0.47)
0.016 20.0
(0.406) (0.59)
* Tips are tested in water.
Fluid output (Q) at other pressures (P) can be calculated by this formula: Q = (0.041) (QT) where QT = fluid
output (fl oz/min) at 600 psi from the above table for the selected orifice size.
Round Spray Spray Tips Tips
Round Round Spray Tips
To convert the gun to a round spray pattern, use
round spray conversion kit 24N391. See manual
3A2499.
Part No. No. Size No. No.
Part Part No. Size Size No.
236836 4A
236837 6A
236838 7A
236839 5B
236840 7B
236841 9B
236842 11B
* Flows are based on white acrylic, enamel paint.
3A7504A
Spray Tip Selection Chart (Model L60M19 MRG Gun Only)
Pre - - - Orifice Orifice Spray Spray Tips
Pre Orifice Spray
No. AEFxxx, AEFxxx, where xxx = 3–digit number from the matrix below.
Output Output
(l/min)
(l/min)
at at at 1000 1000 1000 6 6 6 - - - 8 8 8 (150 (150- - - (150
psi (7.0 (7.0 200)
psi psi (7.0 200) 200)
MPa, MPa, 70 MPa, 70 70
bar)
bar) bar)
7.7 (0.22)
12.5 310
(0.37)
16.0 312
(0.47)
21.0 314
(0.62)
26.5
(0.78)
Approximate Flow
Approximate Approximate
300 psi psi (2.1 (2.1 MPa, MPa, 21
300 300 psi (2.1 MPa,
2.5 oz/min (73 cc/min)
2.9 oz/min (86 cc/min)
3.2 oz/min (95 cc/min)
5.4 oz/min (160 cc/min)
7.1 oz/min (210 cc/min)
8.8 oz/min (260 cc/min)
11.8 oz/min (350 cc/min)
Tips
Tips
Maximum Maximum Pattern Maximum Pattern Pattern Width Width Width at at at 12
in. (mm)
in. in.
8 8 8 - - - 10 10 10 10 10 10- - - 12 12 12
(200- - - 250) 250) (250- - - 300) 300)
(200 (200 250) (250 (250 300)
Spray Tip
Spray Spray
410 510
412 512
414 514
416 516
Flow Rates Rates for for Light Light to to to Medium
Flow Rates for Light
(20–40 (20–40 (20–40 centipoise)* centipoise)* centipoise)*
21 bar) bar) 600 600 psi psi (4.2 (4.2 MPa, MPa, 42
21 bar) 600 psi (4.2 MPa,
4.1 oz/min (120 cc/min)
5.1 oz/min (150 cc/min)
5.4 oz/min (160 cc/min)
7.8 oz/min (230 cc/min)
9.1 oz/min (270 cc/min)
11.8 oz/min (350 cc/min)
16.2 oz/min (480 cc/min)
12 12 in. in. in. (305 (305 (305 mm) mm) mm)
(mm)
(mm)
12- - - 14 12 12 14 14 14 14- - - 16 14 16 16
(300- - - 350) 350) (350- - - 400) 400)
(300 (300 350) (350 (350 400)
Tip
Tip
608
610 710
612 712
614 714
616 716
Medium Viscosity Viscosity Coatings Coatings
Medium Viscosity Coatings
42 bar) bar) 1200 psi psi (8.4
42 bar) 1200 1200 psi
84 bar) 84 84
5.7 oz/min (170 cc/min)
7.4 oz/min (220 cc/min)
7.8 oz/min (230 cc/min)
11.0 oz/min (330 cc/min)
14.2 oz/min (420 cc/min)
17.9 oz/min (530 cc/min)
23.7 oz/min (700 cc/min)
16 16 16- - - 18 18 18
(400- - - 450) 450)
(400 (400 450)
810
812
814
(8.4 MPa, MPa,
(8.4 MPa,
bar) bar)
87