Page 1 Prestige 660RU-Tx Series ADSL2+ Ethernet/USB Gateway User’s Guide Version 3.40 January 2005...
Page 4: Federal Communications Commission (Fcc) Interference Statement
Prestige 660RU-Tx Series User’s Guide Federal Communications Commission (FCC) Interference This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired operations.
Page 5: Zyxel Limited Warranty
ZyXEL Limited Warranty ZyXEL warrants to the original end user (purchaser) that this product is free from any defects in materials or workmanship for a period of up to two years from the date of purchase. During the warranty period, and upon proof of purchase, should the product have indications of failure due to faulty workmanship and/or materials, ZyXEL will, at its discretion, repair or replace the defective products or components without charge for either parts or labor, and to whatever extent it shall deem necessary to restore the product or components to proper operating...
Page 6: Customer Support
+47 22 80 61 81 +46 31 744 7700 www.zyxel.se +46 31 744 7701 +358-9-4780-8411 www.zyxel.fi +358-9-4780 8448 REGULAR MAIL ZyXEL Communications Corp. 6 Innovation Road II Science Park Hsinchu 300 Taiwan ZyXEL Communications Inc. 1130 N. Miller St. Anaheim CA 92806-2001 U.S.A.
Page 7: Table Of Contents
Copyright ... 2 Federal Communications Commission (FCC) Interference Statement ... 3 ZyXEL Limited Warranty... 4 Customer Support... 5 Table of Contents ... 6 List of Figures ... 16 List of Tables ... 22 Preface ... 26 Introduction to DSL... 28 Chapter 1 Getting To Know Your Prestige...
Page 8 Prestige 660RU-Tx Series User’s Guide 3.1.1 Encapsulation ...42 3.1.1.1 ENET ENCAP ...42 3.1.1.2 PPP over Ethernet ...42 3.1.1.3 PPPoA ...42 3.1.1.4 RFC 1483 ...43 3.1.2 Multiplexing ...43 3.1.2.1 VC-based Multiplexing ...43 3.1.2.2 LLC-based Multiplexing ...43 3.1.3 VPI and VCI ...43 3.1.4 Internet Access Wizard Setup: First Screen ...43 3.2 IP Address and Subnet Mask ...44 3.2.1 IP Address Assignment ...45...
Page 9 5.6 Configuring LAN ...61 Chapter 6 WAN Setup... 64 6.1 WAN Overview ...64 6.2 Metric ...64 6.3 PPPoE Encapsulation ...65 6.4 Traffic Shaping ...65 6.5 Zero Configuration Internet Access ...66 6.6 Configuring WAN Setup ...66 6.7 Traffic Redirect ...69 6.8 Configuring WAN Backup ...70 Chapter 7 Network Address Translation (NAT) Screens ...
Page 10 Prestige 660RU-Tx Series User’s Guide Chapter 10 Remote Management Configuration ... 90 10.1 Remote Management Overview ...90 10.1.1 Remote Management Limitations ...90 10.1.2 Remote Management and NAT ...91 10.1.3 System Timeout ...91 10.2 Telnet ...91 10.3 FTP ...91 10.4 Web ...91 10.5 Configuring Remote Management ...91 Chapter 11 Universal Plug-and-Play (UPnP) ...
Page 11 Chapter 14 Menu 1 General Setup ... 124 14.1 General Setup ...124 14.2 Procedure To Configure Menu 1 ...124 14.2.1 Procedure to Configure Dynamic DNS ...125 Chapter 15 Menu 2 WAN Backup Setup ... 128 15.1 Introduction to WAN Backup Setup ...128 15.2 Configuring Dial Backup in Menu 2 ...128 15.2.1 Traffic Redirect Setup ...129 Chapter 16...
Page 12 Prestige 660RU-Tx Series User’s Guide 18.5 Editing ATM Layer Options ...151 18.5.1 VC-based Multiplexing (non-PPP Encapsulation) ...151 18.5.2 LLC-based Multiplexing or PPP Encapsulation ...152 18.5.3 Advance Setup Options ...152 Chapter 19 Static Route Setup ... 154 19.1 IP Static Route Overview ...154 19.2 Configuration ...154 Chapter 20 Bridging Setup ...
Page 13 22.6 Example Filter ...187 22.7 Applying Filters and Factory Defaults ...190 22.7.1 Ethernet Traffic ...190 22.7.2 Remote Node Filters ...190 Chapter 23 SNMP Configuration ... 192 23.1 About SNMP ...192 23.2 Supported MIBs ...193 23.3 SNMP Configuration ...193 23.4 SNMP Traps ...194 Chapter 24 System Information and Diagnosis ...
Page 14 Prestige 660RU-Tx Series User’s Guide 25.4.4 FTP Session Example of Firmware File Upload ...215 25.4.5 TFTP File Upload ...215 25.4.6 TFTP Upload Command Example ...216 Chapter 26 System Maintenance... 218 26.1 Command Interpreter Mode ...218 26.2 Call Control Support ...219 26.2.1 Budget Management ...219 26.3 Time and Date Setting ...220 26.3.1 Resetting the Time ...221...
Page 15 30.7 Problems with the Password ...244 30.8 Problems with the Web Configurator ...245 30.9 Problems with Remote Management ...245 Appendix A Splitters and Microfilters ... 246 Connecting a POTS Splitter ... 246 Telephone Microfilters ... 246 Prestige With ISDN ... 247 Appendix B Setting up Your Computer’s IP Address...
Page 16 Prestige 660RU-Tx Series User’s Guide Appendix E Virtual Circuit Topology ... 270 ... 270 Appendix F Command Interpreter... 272 Command Syntax... 272 Command Usage ... 272 Appendix G Log Descriptions... 274 Index... 280...
Page 17: List Of Figures
Prestige 660RU-Tx Series User’s Guide List of Figures Figure 1 Prestige Internet Access Application ... 35 Figure 2 Prestige LAN-to-LAN Application ... 36 Figure 3 Password Screen ... 38 Figure 4 Change Password at Login ... 39 Figure 5 Web Configurator: Site Map Screen ... 40 Figure 6 Internet Access Wizard Setup: First Screen ...
Page 18 Prestige 660RU-Tx Series User’s Guide Figure 37 Network Connections ... 97 Figure 38 Windows Optional Networking Components Wizard ... 98 Figure 39 Networking Services ... 99 Figure 40 Network Connections ... 100 Figure 41 Internet Connection Properties ... 101 Figure 42 Internet Connection Properties: Advanced Settings ... 102 Figure 43 Internet Connection Properties: Advanced Settings: Add ...
Page 19 Prestige 660RU-Tx Series User’s Guide Figure 80 Menu 21 Filer Set Configuration ... 150 Figure 81 Menu 21.11 WebSet 11 ... 150 Figure 82 Menu 21.12 WebSet 12 ... 151 Figure 83 Menu 11.6 for VC-based Multiplexing ... 152 Figure 84 Menu 11.6 for LLC-based Multiplexing or PPP Encapsulation ... 152 Figure 85 Menu 11.1 Remote Node Profile ...
Page 20 Prestige 660RU-Tx Series User’s Guide Figure 123 Menu 21.5.1 Generic Filter Rule ... 186 Figure 124 Protocol and Device Filter Sets ... 187 Figure 125 Sample Telnet Filter ... 188 Figure 126 Menu 21.6.1 Sample Filter ... 189 Figure 127 Menu 21.6.1 Sample Filter Rules Summary ... 189 Figure 128 Filtering Ethernet Traffic ...
Page 21 Prestige 660RU-Tx Series User’s Guide Figure 166 Menu 26.1 Schedule Set Setup ... 239 Figure 167 Applying Schedule Set(s) to a Remote Node (PPPoE) ... 240 Figure 168 Connecting a POTS Splitter ... 246 Figure 169 Connecting a Microfilter ... 247 Figure 170 Prestige with ISDN ...
Page 22 Prestige 660RU-Tx Series User’s Guide...
Page 23: List Of Tables
Prestige 660RU-Tx Series User’s Guide List of Tables Table 1 ADSL Standards ... 30 Table 2 Front Panel LED Description ... 36 Table 3 Web Configurator Screens Summary ... 40 Table 4 Internet Access Wizard Setup: First Screen ... 44 Table 5 Internet Connection with PPPoE ...
Page 24 Prestige 660RU-Tx Series User’s Guide Table 37 Menu 2 WAN Backup Setup ... 129 Table 38 Menu 2.1Traffic Redirect Setup ... 130 Table 39 DHCP Ethernet Setup ... 134 Table 40 TCP/IP Ethernet Setup ... 134 Table 41 Menu 3.2.1 IP Alias Setup ... 138 Table 42 Menu 4 Internet Access Setup ...
Page 25 Prestige 660RU-Tx Series User’s Guide Table 80 Troubleshooting the Password ... 244 Table 81 Troubleshooting the Web Configurator ... 245 Table 82 Troubleshooting Remote Management ... 245 Table 83 Classes of IP Addresses ... 260 Table 84 Allowed IP Address Range By Class ... 261 Table 85 “Natural”...
Page 26 Prestige 660RU-Tx Series User’s Guide...
Page 27: Preface
Congratulations on your purchase of the Prestige 660RU-Tx ADSL2+ Ethernet/USB Gateway. Note: Register your product online to receive e-mail notices of firmware upgrades and information at www.us.zyxel.com Your Prestige is easy to install and configure. About This User's Guide This manual is designed to guide you through the configuration of your Prestige for its various applications.
Page 28: User Guide Feedback
Help us help you. E-mail all User Guide-related comments, questions or suggestions for improvement to techwriters@zyxel.com.tw or send regular mail to The Technical Writing Team, ZyXEL Communications Corp., 6 Innovation Road II, Science-Based Industrial Park, Hsinchu, 300, Taiwan. Thank you.
Page 29: Introduction To Dsl
Prestige 660RU-Tx Series User’s Guide Introduction to DSL DSL (Digital Subscriber Line) technology enhances the data capacity of the existing twisted- pair wire that runs between the local telephone company switching offices and most homes and offices. While the wire itself can handle higher frequencies, the telephone switching equipment is designed to cut off signals above 4,000 Hz to filter noise off the voice line, but now everybody is searching for ways to get more bandwidth to improve access to the Web - hence DSL technologies.
Page 30 Prestige 660RU-Tx Series User’s Guide Introduction to DSL...
Page 31: Getting To Know Your Prestige
This chapter describes the key features and applications of your Introducing the Prestige Your Prestige integrates high-speed 10/100Mbps auto-negotiating LAN interface(s) and a high-speed ADSL port into a single package. The Prestige is ideal for high-speed Internet browsing and making LAN-to-LAN connections to remote networks. The Prestige is an ADSL router compatible with the ADSL/ADSL2/ADSL2+ standards.
Page 32: Features Of The Prestige
Prestige 660RU-Tx Series User’s Guide 1.1.1 Features of the Prestige The following sections describe the features of the Prestige. High Speed Internet Access Your Prestige ADSL/ADSL2/ADSL2+ router can support downstream transmission rates of up to 24Mbps and upstream transmission rates of 3.5Mbps. Actual speeds attained depend on ISP DSLAM environment.
Page 33: Dynamic Dns Support
PPPoE Support (RFC2516) PPPoE (Point-to-Point Protocol over Ethernet) emulates a dial-up connection. It allows your ISP to use their existing network configuration with newer broadband technologies such as ADSL. The PPPoE driver on the Prestige is transparent to the computers on the LAN, which see only Ethernet and are not aware of PPPoE thus saving you from having to manage PPPoE clients on individual computers.
Page 34: Protocol Support
Prestige 660RU-Tx Series User’s Guide • PPP over AAL5 (RFC 2364). • PPP over Ethernet over AAL5 (RFC 2516). • RFC 1661. • PPP over PAP (RFC 1334). • PPP over CHAP (RFC 1994). Protocol Support • DHCP Support DHCP (Dynamic Host Configuration Protocol) allows the individual clients (computers) to obtain the TCP/IP configuration at start-up from a centralized DHCP server.
Page 35: Network Management
Encapsulation The Prestige supports PPPoA (RFC 2364 - PPP over ATM Adaptation Layer 5), RFC 1483 encapsulation over ATM, MAC encapsulated routing (ENET encapsulation) as well as PPP over Ethernet (RFC 2516). Network Management • Menu driven SMT (System Management Terminal) management •...
Page 36: Applications For The Prestige
Prestige 660RU-Tx Series User’s Guide Housing Your Prestige's compact and ventilated housing minimizes space requirements making it easy to position anywhere in your busy office. 1.1.2 Applications for the Prestige Here are some example uses for which the Prestige is well suited. 1.1.2.1 Internet Access The Prestige is the ideal high-speed Internet access solution.
Page 37: Prestige Hardware Installation And Connection
Figure 2 Prestige LAN-to-LAN Application 1.1.3 Prestige Hardware Installation and Connection Refer to the Quick Start Guide for information on hardware installation and connection. 1.1.4 Front Panel LEDs The following table describes the LEDs on the front panel. Table 2 Front Panel LED Description COLOR PWR/SYS Green...
Page 38 Prestige 660RU-Tx Series User’s Guide Chapter 1 Getting To Know Your Prestige...
Page 39: Introducing The Web Configurator
This chapter describes how to access and navigate the web configurator. 2.1 Web Configurator Overview The web configurator is an HTML-based management interface that allows easy Prestige setup and management via Internet browser. Use Internet Explorer 6.0 and later or Netscape Navigator 7.0 and later versions with JavaScript enabled.
Page 40: Resetting The Prestige
Prestige 660RU-Tx Series User’s Guide 6 It is highly recommended you change the default password! Enter a new password, retype it to confirm and click Apply; alternatively click Ignore to proceed to the main menu if you do not want to change the password now. Note: If you do not change the password, the following screen appears every time you log in.
Page 41: Figure 5 Web Configurator: Site Map Screen
• Click Wizard Setup to begin a series of screens to configure your Prestige for the first time. • Click a link under Advanced Setup to configure advanced Prestige features. • Click a link under Maintenance to see Prestige performance statistics, upload firmware and back up, restore or upload a configuration file.
Page 42 Prestige 660RU-Tx Series User’s Guide Table 3 Web Configurator Screens Summary (continued) LINK SUB-LINK Remote Management UPnP Maintenance System Status DHCP Table Any IP Table Diagnostic General DSL Line Firmware LOGOUT FUNCTION Use this screen to configure through which interface(s) and from which IP address(es) users can use Telnet/FTP/Web to manage the Prestige.
Page 43: Chapter 3 Wizard Setup
This chapter provides information on the Wizard Setup screens for Internet access in the web configurator. 3.1 Introduction Use the Wizard Setup screens to configure your system for Internet access with the information (provided by your ISP) that you fill in the Internet Account Information table of the Quick Start Guide.
Page 44: Rfc 1483
Prestige 660RU-Tx Series User’s Guide 3.1.1.4 RFC 1483 RFC 1483 describes two methods for Multiprotocol Encapsulation over ATM Adaptation Layer 5 (AAL5). The first method allows multiplexing of multiple protocols over a single ATM virtual circuit (LLC-based multiplexing) and the second method assumes that each protocol is carried over a separate ATM virtual circuit (VC-based multiplexing).
Page 45: Ip Address And Subnet Mask
Figure 6 Internet Access Wizard Setup: First Screen The following table describes the labels in this screen. Table 4 Internet Access Wizard Setup: First Screen LABEL DESCRIPTION Mode From the Mode drop-down list box, select Routing (default) if your ISP allows multiple computers to share an Internet account.
Page 46: Ip Address Assignment
Prestige 660RU-Tx Series User’s Guide If the ISP did not explicitly give you an IP network number, then most likely you have a single user account and the ISP will assign you a dynamic IP address when the connection is established.
Page 47: Private Ip Addresses
3.2.1.4 Private IP Addresses Every machine on the Internet must have a unique address. If your networks are isolated from the Internet, for example, only between your two branch offices, you can assign any IP addresses to the hosts without problems. However, the Internet Assigned Numbers Authority (IANA) has reserved the following three blocks of IP addresses specifically for private networks: •...
Page 48: Figure 7 Internet Connection With Pppoe
Prestige 660RU-Tx Series User’s Guide Figure 7 Internet Connection with PPPoE The following table describes the labels in this screen. Table 5 Internet Connection with PPPoE LABEL DESCRIPTION Service Name Type the name of your PPPoE service here. User Name Enter the user name exactly as your ISP assigned.
Page 49: Figure 8 Internet Connection With Rfc 1483
Figure 8 Internet Connection with RFC 1483 The following table describes the labels in this screen. Table 6 Internet Connection with RFC 1483 LABEL DESCRIPTION IP Address This field is available if you select Routing in the Mode field. Type your ISP assigned IP address in this field. Network Address Select None, SUA Only or Full Feature from the drop-down list box.
Page 50: Figure 10 Internet Connection With Pppoa
Prestige 660RU-Tx Series User’s Guide The following table describes the labels in this screen. Table 7 Internet Connection with ENET ENCAP LABEL DESCRIPTION IP Address A static IP address is a fixed IP that your ISP gives you. A dynamic IP address is not fixed;...
Page 51: Dhcp Setup
The following table describes the labels in this screen. Table 8 Internet Connection with PPPoA LABEL DESCRIPTION User Name Enter the login name that your ISP gives you. Password Enter the password associated with the user name above. IP Address This option is available if you select Routing in the Mode field.
Page 52: Figure 11 Internet Access Wizard Setup: Third Screen
Prestige 660RU-Tx Series User’s Guide Figure 11 Internet Access Wizard Setup: Third Screen If you want to change your Prestige LAN settings, click Change LAN Configuration to display the screen as shown next. Chapter 3 Wizard Setup...
Page 53: Figure 12 Internet Access Wizard Setup: Lan Configuration
Figure 12 Internet Access Wizard Setup: LAN Configuration The following table describes the labels in this screen. Table 9 Internet Access Wizard Setup: LAN Configuration LABEL LAN IP Address LAN Subnet Mask DHCP DHCP Server Client IP Pool Starting Address Size of Client IP Pool Primary DNS Server Secondary DNS Server As above.
Page 54: Internet Access Wizard Setup: Connection Test
Prestige 660RU-Tx Series User’s Guide 3.2.7 Internet Access Wizard Setup: Connection Test The Prestige automatically tests the connection to the computer(s) connected to the LAN ports. To test the connection from the Prestige to the ISP, click Start Diagnose. Otherwise click Return to Main Menu to go back to the Site Map screen.
Page 55: Chapter 4 Password Setup
This chapter provides information on the Password screen. 4.1 Password Overview It is highly recommended that you change the password for accessing the Prestige. 4.1.1 Configuring Password To change your Prestige’s password (recommended), click Password in the Site Map screen. The screen appears as shown.
Page 56 Prestige 660RU-Tx Series User’s Guide Chapter 4 Password Setup...
Page 57: Chapter 5 Lan Setup
This chapter describes how to configure LAN settings. 5.1 LAN Overview A Local Area Network (LAN) is a shared communication system to which many computers are attached. A LAN is a computer network limited to the immediate area, usually the same building or floor of a building.
Page 58: Dns Server Address
Prestige 660RU-Tx Series User’s Guide 5.2 DNS Server Address DNS (Domain Name System) is for mapping a domain name to its corresponding IP address and vice versa. The DNS server is extremely important because without it, you must know the IP address of a machine before you can access it.
Page 59: Lan Tcp/Ip
5.4 LAN TCP/IP The Prestige has built-in DHCP server capability that assigns IP addresses and DNS servers to systems that support DHCP client capability. 5.4.1 Factory LAN Defaults The LAN parameters of the Prestige are preset in the factory with the following values: •...
Page 60: Multicast
Prestige 660RU-Tx Series User’s Guide 5.4.4 Multicast Traditionally, IP packets are transmitted in one of either two ways - Unicast (1 sender - 1 recipient) or Broadcast (1 sender - everybody on the network). Multicast delivers IP packets to a group of hosts on the network - not everybody and not just 1. IGMP (Internet Group Multicast Protocol) is a network-layer protocol used to establish membership in a Multicast group - it is not used to carry user data.
Page 61: How Any Ip Works
Figure 16 Any IP Example The Any IP feature does not apply to a computer using either a dynamic IP address or a static IP address that is in the same subnet as the Prestige’s IP address. Note: You must enable NAT/SUA to use the Any IP feature on the Prestige. 5.5.1 How Any IP Works Address Resolution Protocol (ARP) is a protocol for mapping an Internet Protocol address (IP address) to a physical machine address, also known as a Media Access Control or MAC...
Page 62: Configuring Lan
Prestige 660RU-Tx Series User’s Guide After all the routing information is updated, the computer can access the Prestige and the Internet as if it is in the same subnet as the Prestige. 5.6 Configuring LAN Click LAN and LAN Setup to open the following screen. Figure 17 LAN Setup The following table describes the labels in this screen.
Page 63 Table 11 LAN Setup (continued) LABEL DESCRIPTION Client IP Pool This field specifies the first of the contiguous addresses in the IP address pool. Starting Address Size of Client IP This field specifies the size or count of the IP address pool. Pool Primary DNS Server Enter the IP addresses of the DNS servers.
Page 64 Prestige 660RU-Tx Series User’s Guide Chapter 5 LAN Setup...
Page 65: Chapter 6 Wan Setup
This chapter describes how to configure WAN settings. 6.1 WAN Overview A WAN (Wide Area Network) is an outside connection to another network or the Internet. Chapter 3 Wizard Setup 6.2 Metric The metric represents the "cost of transmission". A router determines the best route for transmission by choosing a path with the lowest "cost".
Page 66: Pppoe Encapsulation
Prestige 660RU-Tx Series User’s Guide 6.3 PPPoE Encapsulation The Prestige supports PPPoE (Point-to-Point Protocol over Ethernet). PPPoE is an IETF Draft standard (RFC 2516) specifying how a personal computer (PC) interacts with a broadband modem (DSL, cable, wireless, etc.) connection. The PPPoE option is for a dial-up connection using PPPoE.
Page 67: Zero Configuration Internet Access
Figure 18 Example of Traffic Shaping 6.5 Zero Configuration Internet Access Once you turn on and connect the Prestige to a telephone jack, it automatically detects the Internet connection settings (such as the VCI/VPI numbers and the encapsulation method) from the ISP and makes the necessary configuration changes. In cases where additional account information (such as an Internet account user name and password) is required or the Prestige cannot connect to the ISP, you will be redirected to web screen(s) for information input or troubleshooting.
Page 68: Figure 19 Wan Setup (Pppoe)
Prestige 660RU-Tx Series User’s Guide Figure 19 WAN Setup (PPPoE) The following table describes the labels in this screen. Table 12 WAN Setup LABEL Name Mode DESCRIPTION Enter the name of your Internet Service Provider, e.g., MyISP. This information is for identification purposes only.
Page 69 Table 12 WAN Setup (continued) LABEL Encapsulation Multiplex Virtual Circuit ID ATM QoS Type Cell Rate Peak Cell Rate Sustain Cell Rate Maximum Burst Size Maximum Burst Size (MBS) refers to the maximum number of cells that can be Login Information Service Name User Name Password...
Page 70: Traffic Redirect
Prestige 660RU-Tx Series User’s Guide Table 12 WAN Setup (continued) LABEL Max Idle Timeout PPPoE Passthrough (PPPoE encapsulation only) Subnet Mask (ENET ENCAP encapsulation only) ENET ENCAP Gateway (ENET ENCAP encapsulation only) Zero Configuration Back Apply Cancel 6.7 Traffic Redirect Traffic redirect forwards traffic to a backup gateway when the Prestige cannot connect to the Internet.
Page 71: Configuring Wan Backup
Figure 20 Traffic Redirect Example The following network topology allows you to avoid triangle route security issues when the backup gateway is connected to the LAN. Use IP alias to configure the LAN into two or three logical networks with the Prestige itself as the gateway for each LAN network. Put the protected LAN in one subnet (Subnet 1 in the following figure) and the backup gateway in another subnet (Subnet 2).
Page 72: Figure 22 Wan Backup
Prestige 660RU-Tx Series User’s Guide Figure 22 WAN Backup The following table describes the labels in this screen. Table 13 WAN Backup LABEL DESCRIPTION Backup Type Select the method that the Prestige uses to check the DSL connection. Select DSL Link to have the Prestige check if the connection to the DSLAM is up. Select ICMP to have the Prestige periodically ping the IP addresses configured in the Check WAN IP Address fields.
Page 73 Table 13 WAN Backup (continued) LABEL DESCRIPTION Traffic Redirect Active Select this check box to have the Prestige use traffic redirect if the normal WAN connection goes down. Note: If you activate traffic redirect, you must configure at least one Check WAN IP Address.
Page 74 Prestige 660RU-Tx Series User’s Guide Chapter 6 WAN Setup...
Page 75: Network Address Translation (Nat) Screens
Network Address Translation This chapter discusses how to configure NAT on the Prestige. 7.1 NAT Overview NAT (Network Address Translation - NAT, RFC 1631) is the translation of the IP address of a host in a packet, for example, the source address of an outgoing packet, used within one network to a different IP address known within another network.
Page 76: What Nat Does
Prestige 660RU-Tx Series User’s Guide Note: NAT never changes the IP address (either local or global) of an outside host. 7.1.2 What NAT Does In the simplest form, NAT changes the source IP address in a packet received from a subscriber (the inside local address) to another (the inside global address) before forwarding the packet to the WAN side.
Page 77: Nat Application
Figure 23 How NAT Works 7.1.4 NAT Application The following figure illustrates a possible NAT application, where three inside LANs (logical LANs using IP Alias) behind the Prestige can communicate with three distinct WAN networks. More examples follow at the end of this chapter. Figure 24 NAT Application With IP Alias 7.1.5 NAT Mapping Types NAT supports five types of IP/port mapping.
Page 78: Sua (Single User Account) Versus Nat
Prestige 660RU-Tx Series User’s Guide • One to One: In One-to-One mode, the Prestige maps one local IP address to one global IP address. • Many to One: In Many-to-One mode, the Prestige maps multiple local IP addresses to one global IP address. This is equivalent to SUA (for instance, PAT, port address translation), ZyXEL’s Single User Account feature that previous ZyXEL routers supported (the SUA Only option in today’s routers).
Page 79: Sua Server
Note: 1. Choose SUA Only if you have just one public WAN IP address for your Prestige. 2. Choose Full Feature if you have multiple public WAN IP addresses for your Prestige. 7.3 SUA Server A SUA server set is a list of inside (behind NAT on the LAN) servers, for example, web or FTP, that you can make visible to the outside world even though SUA makes your whole inside network appear as a single computer to the outside world.
Page 80: Configuring Servers Behind Sua (Example)
Prestige 660RU-Tx Series User’s Guide Table 16 Services and Port Numbers (continued) SERVICES SMTP (Simple Mail Transfer Protocol) DNS (Domain Name System) Finger HTTP (Hyper Text Transfer protocol or WWW, Web) POP3 (Post Office Protocol) NNTP (Network News Transport Protocol) SNMP (Simple Network Management Protocol) SNMP trap PPTP (Point-to-Point Tunneling Protocol)
Page 81: Configuring Sua Server
Figure 26 NAT Mode The following table describes the labels in this screen. Table 17 NAT Mode LABEL DESCRIPTION None Select this radio button to disable NAT. SUA Only Select this radio button if you have just one public WAN IP address for your Prestige. The Prestige uses Address Mapping Set 1 in the NAT - Edit SUA/NAT Server Set screen.
Page 82: Figure 27 Edit Sua/Nat Server Set
Prestige 660RU-Tx Series User’s Guide Figure 27 Edit SUA/NAT Server Set The following table describes the labels in this screen. Table 18 Edit SUA/NAT Server Set LABEL Start Port No. Enter a port number in this field. To forward only one port, enter the port number again in the End Port No. field. To forward a series of ports, enter the start port number here and the end port number in the End Port No.
Page 83: Configuring Address Mapping
7.6 Configuring Address Mapping Ordering your rules is important because the Prestige applies the rules in the order that you specify. When a rule matches the current packet, the Prestige takes the corresponding action and the remaining rules are ignored. If there are any empty rules before your new configured rule, your configured rule will be pushed up by that number of empty rules.
Page 84: Editing An Address Mapping Rule
Prestige 660RU-Tx Series User’s Guide Table 19 Address Mapping Rules (continued) LABEL DESCRIPTION Type 1-1: One-to-one mode maps one local IP address to one global IP address. Note that port numbers do not change for the One-to-one NAT mapping type. M-1: Many-to-One mode maps multiple local IP addresses to one global IP address.
Page 85: Table 20 Address Mapping Rule Edit
Table 20 Address Mapping Rule Edit LABEL Type Choose the port mapping type from one of the following. • One-to-One: One-to-One mode maps one local IP address to one global IP address. Note that port numbers do not change for One-to-one NAT mapping type.
Page 86 Prestige 660RU-Tx Series User’s Guide Chapter 7 Network Address Translation (NAT) Screens...
Page 87: Chapter 8 Dynamic Dns Setup
This chapter discusses how to configure your Prestige to use Dynamic DNS. 8.1 Dynamic DNS Dynamic DNS allows you to update your current dynamic IP address with one or many dynamic DNS services so that anyone can contact you (in NetMeeting, CU-SeeMe, etc.). You can also access your FTP server or Web site on your own computer using a domain name (for instance myhost.dhs.org, where myhost is a name of your choice) that will never change instead of using an IP address that changes each time you reconnect.
Page 88: Figure 30 Dynamic Dns
Prestige 660RU-Tx Series User’s Guide Figure 30 Dynamic DNS The following table describes the labels in this screen. Table 21 Dynamic DNS LABEL DESCRIPTION Active Select this check box to use dynamic DNS. Service Provider This is the name of your Dynamic DNS service provider. Host Names Type the domain name assigned to your Prestige by your Dynamic DNS provider.
Page 89: Chapter 9 Time And Date
This screen is not available on all models. Use this screen to configure the Prestige’s time and date settings. 9.1 Configuring Time and Date To change your Prestige’s time and date, click Time And Date. The screen appears as shown. Use this screen to configure the Prestige’s time based on your local time zone.
Page 90: Table 22 Time And Date
Prestige 660RU-Tx Series User’s Guide Table 22 Time and Date LABEL DESCRIPTION Time Server Use Protocol when Select the time service protocol that your time server sends when you turn on the Bootup Prestige. Not all time servers support all protocols, so you may have to check with your ISP/network administrator or use trial and error to find a protocol that works.
Page 91: Remote Management Configuration
This chapter provides information on configuring remote management. 10.1 Remote Management Overview Remote management allows you to determine which services/protocols can access which Prestige interface (if any) from which computers. You may manage your Prestige from a remote location via: •...
Page 92: Remote Management And Nat
Prestige 660RU-Tx Series User’s Guide 10.1.2 Remote Management and NAT When NAT is enabled: • Use the Prestige’s WAN IP address when configuring from the WAN. • Use the Prestige’s LAN IP address when configuring from the LAN. 10.1.3 System Timeout There is a default system management idle timeout of five minutes (three hundred seconds).
Page 93: Figure 33 Remote Management
Figure 33 Remote Management The following table describes the labels in this screen. Table 23 Remote Management LABEL DESCRIPTION Server Type Each of these labels denotes a service that you may use to remotely manage the Prestige. Access Status Select the access interface. Choices are All, LAN Only, WAN Only and Disable. Port This field shows the port number for the remote management service.
Page 94 Prestige 660RU-Tx Series User’s Guide Chapter 10 Remote Management Configuration...
Page 95: Universal Plug-And-Play (Upnp)
Universal Plug-and-Play (UPnP) This chapter introduces the UPnP feature in the web configurator. 11.1 Introducing Universal Plug and Play Universal Plug and Play (UPnP) is a distributed, open networking standard that uses TCP/IP for simple peer-to-peer network connectivity between devices. A UPnP device can dynamically join a network, obtain an IP address, convey its capabilities and learn about other devices on the network.
Page 96: Upnp And Zyxel
Prestige 660RU-Tx Series User’s Guide All UPnP-enabled devices may communicate freely with each other without additional configuration. Disable UPnP if this is not your intention. 11.2 UPnP and ZyXEL ZyXEL has achieved UPnP certification from the Universal Plug and Play Forum Creates UPnP™...
Page 97: Installing Upnp In Windows Example
11.3 Installing UPnP in Windows Example This section shows how to install UPnP in Windows Me and Windows XP. Installing UPnP in Windows Me Follow the steps below to install the UPnP in Windows Me. 1 Click Start and Control Panel. Double-click Add/Remove Programs. 2 Click on the Windows Setup tab and select Communication in the Components selection box.
Page 98: Figure 36 Add/Remove Programs: Windows Setup: Communication: Components
Prestige 660RU-Tx Series User’s Guide Figure 36 Add/Remove Programs: Windows Setup: Communication: Components 4 Click OK to go back to the Add/Remove Programs Properties window and click Next. 5 Restart the computer when prompted. Installing UPnP in Windows XP Follow the steps below to install the UPnP in Windows XP. 1 Click Start and Control Panel.
Page 99: Figure 38 Windows Optional Networking Components Wizard
Prestige 660RU-Tx Series User’s Guide Figure 38 Windows Optional Networking Components Wizard 5 In the Networking Services window, select the Universal Plug and Play check box. Chapter 11 Universal Plug-and-Play (UPnP)
Page 100: Using Upnp In Windows Xp Example
Prestige 660RU-Tx Series User’s Guide Figure 39 Networking Services 6 Click OK to go back to the Windows Optional Networking Component Wizard window and click Next. 11.4 Using UPnP in Windows XP Example This section shows you how to use the UPnP feature in Windows XP. You must already have UPnP installed in Windows XP and UPnP activated on the Prestige.
Page 101: Figure 40 Network Connections
Prestige 660RU-Tx Series User’s Guide Figure 40 Network Connections 3 In the Internet Connection Properties window, click Settings to see the port mappings there were automatically created. Chapter 11 Universal Plug-and-Play (UPnP)
Page 102: Figure 41 Internet Connection Properties
Prestige 660RU-Tx Series User’s Guide Figure 41 Internet Connection Properties 4 You may edit or delete the port mappings or click Add to manually add port mappings. Chapter 11 Universal Plug-and-Play (UPnP)
Page 103: Figure 42 Internet Connection Properties: Advanced Settings
Figure 42 Internet Connection Properties: Advanced Settings Figure 43 Internet Connection Properties: Advanced Settings: Add 5 When the UPnP-enabled device is disconnected from your computer, all port mappings will be deleted automatically. 6 Select Show icon in notification area when connected option and click OK. An icon displays in the system tray.
Page 104: Figure 44 System Tray Icon
Prestige 660RU-Tx Series User’s Guide Figure 44 System Tray Icon 7 Double-click on the icon to display your current Internet connection status. Figure 45 Internet Connection Status Web Configurator Easy Access With UPnP, you can access the web-based configurator on the Prestige without finding out the IP address of the Prestige first.
Page 105: Figure 46 Network Connections
Figure 46 Network Connections 4 An icon with the description for each UPnP-enabled device displays under Local Network. 5 Right-click on the icon for your Prestige and select Invoke. The web configurator login screen displays. Chapter 11 Universal Plug-and-Play (UPnP) Prestige 660RU-Tx Series User’s Guide...
Page 106: Figure 47 Network Connections: My Network Places
Prestige 660RU-Tx Series User’s Guide Figure 47 Network Connections: My Network Places 6 Right-click on the icon for your Prestige and select Properties. A properties window displays with basic information about the Prestige. Chapter 11 Universal Plug-and-Play (UPnP)
Page 107: Figure 48 Network Connections: My Network Places: Properties: Example
Prestige 660RU-Tx Series User’s Guide Figure 48 Network Connections: My Network Places: Properties: Example Chapter 11 Universal Plug-and-Play (UPnP)
Page 108 Prestige 660RU-Tx Series User’s Guide Chapter 11 Universal Plug-and-Play (UPnP)
Page 109: Chapter 12 Maintenance
This chapter displays system information such as ZyNOS firmware, port IP addresses and port traffic statistics. 12.1 Maintenance Overview The maintenance screens can help you view system information, upload new firmware, manage configuration and restart your Prestige. 12.2 System Status Screen Click System Status to open the following screen, where you can use to monitor your Prestige.
Page 110: Figure 49 System Status
Prestige 660RU-Tx Series User’s Guide Figure 49 System Status The following table describes the fields in this screen. Table 25 System Status LABEL DESCRIPTION System Status System Name This is the name of your Prestige. It is for identification purposes. ZyNOS Firmware This is the ZyNOS firmware version and the date the firmware was created.
Page 111: System Statistics
Table 25 System Status (continued) LABEL DESCRIPTION IP Subnet Mask This is the WAN port IP subnet mask. Default Gateway This is the IP address of the default gateway, if applicable. VPI/VCI This is the Virtual Path Identifier and Virtual Channel Identifier that you entered in the first Wizard screen.
Page 112: Dhcp Table Screen
Prestige 660RU-Tx Series User’s Guide The following table describes the labels in this screen. Table 26 System Status: Show Statistics LABEL DESCRIPTION System up Time This is the elapsed time the system has been up. CPU Load This field specifies the percentage of CPU utilization. LAN or WAN Port This is the WAN or LAN port.
Page 113: Any Ip Table Screen
Figure 51 DHCP Table The following table describes the fields in this screen. Table 27 DHCP Table LABEL DESCRIPTION Host Name This is the name of the host computer. IP Address This field displays the IP address relative to the Host Name field. MAC Address This field displays the MAC (Media Access Control) address of the computer with the displayed host name.
Page 114: Diagnostic Screens
Prestige 660RU-Tx Series User’s Guide Table 28 Any IP Table LABEL DESCRIPTION MAC Address This field displays the MAC (Media Access Control) address of the computer with the displayed IP address. Every Ethernet device has a unique MAC address. The MAC address is assigned at the factory and consists of six pairs of hexadecimal characters, for example, 00:A0:C5:00:00:02.
Page 115: Diagnostic Dsl Line Screen
Figure 53 Diagnostic: General The following table describes the labels in this screen. Table 29 Diagnostic: General LABEL DESCRIPTION TCP/IP Type the IP address of a computer that you want to ping in order to test a connection. Address Ping Click this button to ping the IP address that you entered.
Page 116: Figure 54 Diagnostic: Dsl Line
Prestige 660RU-Tx Series User’s Guide Figure 54 Diagnostic: DSL Line The following table describes the labels in this screen. Table 30 Diagnostic: DSL Line LABEL Reset ADSL Click this button to reinitialize the ADSL line. The large text box above then displays Line the progress and results of this operation, for example: "Start to reset ADSL...
Page 117: Firmware Screen
12.6 Firmware Screen Find firmware at www.zyxel.com in a file that (usually) uses the system model name with a .bin extension, for example, "Prestige.bin". The upload process uses HTTP (Hypertext Transfer Protocol) and may take up to two minutes. After a successful upload, the system will reboot.
Page 118: Figure 56 Network Temporarily Disconnected
Prestige 660RU-Tx Series User’s Guide After you see the Firmware Upload in Process screen, wait two minutes before logging into the Prestige again. The Prestige automatically restarts in this time causing a temporary network disconnect. In some operating systems, you may see the following icon on your desktop. Figure 56 Network Temporarily Disconnected After two minutes, log in again and check your new firmware version in the System Status screen.
Page 119: Chapter 13 Introducing The Smt
This chapter explains how to access and navigate the System Management Terminal and gives an overview of its menus. 13.1 SMT Introduction The Prestige’s SMT (System Management Terminal) is a menu-driven interface that you can access from a terminal emulator over a telnet connection. This chapter shows you how to access the SMT (System Management Terminal) menus via Telnet, how to navigate the SMT and how to configure SMT menus.
Page 120: Prestige Smt Menu Overview
Prestige 660RU-Tx Series User’s Guide Figure 58 Login Screen Enter Password : **** 13.1.3 Prestige SMT Menu Overview The following figure gives you an overview of the various SMT menu screens of your Prestige. Figure 59 Prestige SMT Menu Overview 13.2 Navigating the SMT Interface The SMT (System Management Terminal) is the interface that you use to configure your Prestige.
Page 121: Table 32 Navigating The Smt Interface
Several operations that you should be familiar with before you attempt to modify the configuration are listed in the table below. Table 32 Navigating the SMT Interface OPERATION KEY STROKE Move down to [ENTER] another menu Move up to a [ESC] previous menu Move to a hidden...
Page 122: System Management Terminal Interface Summary
Prestige 660RU-Tx Series User’s Guide After you enter the password, the SMT displays the main menu, as shown next. Table 33 SMT Main Menu Copyright (c) 1994 - 2004 ZyXEL Communications Corp. Getting Started 1. General Setup 2. WAN Backup Setup 3.
Page 123: Changing The System Password
13.3 Changing the System Password Change the Prestige default password by following the steps shown next. 1 Enter 23 in the main menu to display Menu 23 - System Password as shown next. 2 Type your existing system password in the Old Password field, for example “ press [ENTER].
Page 124 Prestige 660RU-Tx Series User’s Guide Chapter 13 Introducing the SMT...
Page 125: Chapter 14 Menu 1 General Setup
Menu 1 - General Setup contains administrative and system-related information. 14.1 General Setup Menu 1 — General Setup contains administrative and system-related information (shown next). The System Name field is for identification purposes. However, because some ISPs check this name you should enter your computer's "Computer Name". •...
Page 126: Procedure To Configure Dynamic Dns
Prestige 660RU-Tx Series User’s Guide Figure 61 Menu 1 General Setup Press ENTER to Confirm or ESC to Cancel: Fill in the required fields. Refer to the table shown next for more information about these fields. Table 35 Menu 1 General Setup FIELD System Name Location (optional)
Page 127: Figure 62 Menu 1.1 Configure Dynamic Dns
To configure dynamic DNS, go to Menu 1 — General Setup and select Yes in the Edit Dynamic DNS field. Press [ENTER] to display Menu 1.1— Configure Dynamic DNS as shown next. Figure 62 Menu 1.1 Configure Dynamic DNS Follow the instructions in the next table to configure dynamic DNS parameters. Table 36 Menu 1.1 Configure Dynamic DNS FIELD DESCRIPTION...
Page 128 Prestige 660RU-Tx Series User’s Guide Chapter 14 Menu 1 General Setup...
Page 129: Menu 2 Wan Backup Setup
Menu 2 WAN Backup Setup This chapter describes how to configure traffic redirect using menu 2 and 2.1. 15.1 Introduction to WAN Backup Setup This chapter explains how to configure the Prestige for traffic redirect and dial backup connections. 15.2 Configuring Dial Backup in Menu 2 From the main menu, enter 2 to open menu 2.
Page 130: Traffic Redirect Setup
Prestige 660RU-Tx Series User’s Guide The following table describes the fields in this menu. Table 37 Menu 2 WAN Backup Setup FIELD Check Mechanism Check WAN IP Address1-3 KeepAlive Fail Tolerance Recovery Interval(sec) When the Prestige is using a lower priority connection (usually a WAN backup ICMP Timeout Traffic Redirect When you have completed this menu, press [ENTER] at the prompt “...
Page 131: Figure 64 Menu 2.1Traffic Redirect Setup
Figure 64 Menu 2.1Traffic Redirect Setup Active= No Configuration: Press ENTER to Confirm or ESC to Cancel: The following table describes the fields in this menu. Table 38 Menu 2.1Traffic Redirect Setup FIELD DESCRIPTION Active. Press [SPACE BAR] and select Yes (to enable) or No (to disable) traffic redirect setup.
Page 132 Prestige 660RU-Tx Series User’s Guide Chapter 15 Menu 2 WAN Backup Setup...
Page 133: Chapter 16 Menu 3 Lan Setup
This chapter covers how to configure your wired Local Area Network (LAN) settings. 16.1 LAN Setup This section describes how to configure the Ethernet using Menu 3 — LAN Setup. From the main menu, enter 3 to display menu 3. Figure 65 Menu 3 LAN Setup Menu 3 - LAN Setup 1.
Page 134: Protocol Dependent Ethernet Setup
Prestige 660RU-Tx Series User’s Guide 16.2 Protocol Dependent Ethernet Setup Depending on the protocols for your applications, you need to configure the respective Ethernet Setup, as outlined below. • For TCP/IP Ethernet setup refer to • For bridging Ethernet setup refer to 16.3 CP/IP Ethernet Setup and DHCP Use menu 3.2 to configure your Prestige for TCP/IP.
Page 135: Table 39 Dhcp Ethernet Setup
Follow the instructions in the following table on how to configure the DHCP fields. Table 39 DHCP Ethernet Setup FIELD DHCP Setup DHCP Client IP Pool Starting Address Size of Client IP Pool This field specifies the size or count of the IP address pool. Primary DNS Server Secondary DNS Server...
Page 136 Prestige 660RU-Tx Series User’s Guide Chapter 16 Menu 3 LAN Setup...
Page 137: Chapter 17 Internet Access
This chapter shows you how to configure the LAN and WAN of your Prestige for Internet access 17.1 Internet Access Overview Refer to the chapters on the web configurator’s wizard, LAN and WAN screens for more background information on fields in the SMT screens covered in this chapter. 17.2 IP Policies Traditionally, routing is based on the destination address only and the router takes the shortest path to forward a packet.
Page 138: Ip Alias Setup
Prestige 660RU-Tx Series User’s Guide Figure 68 IP Alias Network Example Use menu 3.2.1 to configure IP Alias on your Prestige. 17.4 IP Alias Setup Use menu 3.2 to configure the first network. Move the cursor to Edit IP Alias field and press [SPACEBAR] to choose Yes and press [ENTER] to configure the second and third network.
Page 139: Route Ip Setup
Figure 70 Menu 3.2.1 IP Alias Setup Menu 3.2.1 - IP Alias Setup IP Alias 1= Yes IP Alias 2= No Follow the instructions in the following table to configure IP Alias parameters. Table 41 Menu 3.2.1 IP Alias Setup FIELD DESCRIPTION IP Alias...
Page 140: Internet Access Configuration
Prestige 660RU-Tx Series User’s Guide Figure 71 Menu 1 General Setup Menu 1 - General Setup Press ENTER to Confirm or ESC to Cancel: 17.6 Internet Access Configuration Menu 4 allows you to enter the Internet Access information in one screen. Menu 4 is actually a simplified setup for one of the remote nodes that you can access in menu 11.
Page 141: Figure 72 Menu 4 Internet Access Setup
Figure 72 Menu 4 Internet Access Setup Menu 4 - Internet Access Setup ISP's Name= MyISP Encapsulation= RFC 1483 Multiplexing= LLC-based VPI #= 8 VCI #= 35 ATM QoS Type= CBR My Login= N/A My Password= N/A ENET ENCAP Gateway= N/A IP Address Assignment= Static Network Address Translation= SUA Only Press ENTER to Confirm or ESC to Cancel:...
Page 142 Prestige 660RU-Tx Series User’s Guide Menu 4 Internet Access Setup Table 42 FIELD DESCRIPTION My Password Enter the password associated with the login name above. ENET ENCAP Enter the gateway IP address supplied by your ISP when you are using ENET Gateway ENCAP encapsulation.
Page 143: Remote Node Configuration
Remote Node Configuration This chapter covers remote node configuration. 18.1 Remote Node Setup Overview This section describes the protocol-independent parameters for a remote node. A remote node is required for placing calls to a remote gateway. A remote node represents both the remote gateway and the network behind it across a WAN connection.
Page 144: Encapsulation And Multiplexing Scenarios
Prestige 660RU-Tx Series User’s Guide Figure 73 Menu 11 Remote Node Setup 18.2.2 Encapsulation and Multiplexing Scenarios For Internet access you should use the encapsulation and multiplexing methods used by your ISP. Consult your telephone company for information on encapsulation and multiplexing methods for LAN-to-LAN applications, for example between a branch office and corporate headquarters.
Page 145: Figure 74 Menu 11.1 Remote Node Profile
Figure 74 Menu 11.1 Remote Node Profile Menu 11.1 - Remote Node Profile Rem Node Name= MyISP Active= Yes Encapsulation= RFC 1483 Multiplexing= LLC-based Service Name= N/A Incoming: Rem Login= N/A Rem Password= N/A Outgoing: My Login= N/A My Password= N/A Authen= N/A Press ENTER to Confirm or ESC to Cancel: In Menu 11.1 –...
Page 146: Outgoing Authentication Protocol
Prestige 660RU-Tx Series User’s Guide Table 43 Menu 11.1 Remote Node Profile (continued) FIELD DESCRIPTION Authen This field sets the authentication protocol used for outgoing calls. Options for this field are: CHAP/PAP – Your Prestige will accept either CHAP or PAP when requested by this remote node.
Page 147: Remote Node Network Layer Options
18.3 Remote Node Network Layer Options For the TCP/IP parameters, perform the following steps to edit Menu 11.3 – Remote Node Network Layer Options as shown next. 1 In menu 11.1, make sure IP is among the protocols in the Route field. 2 Move the cursor to the Edit IP/Bridge field, press [SPACE BAR] to select Yes, then press [ENTER] to display Menu 11.3 –...
Page 148: My Wan Addr Sample Ip Addresses
Prestige 660RU-Tx Series User’s Guide Table 44 Menu 11.3 Remote Node Network Layer Options (continued) FIELD DESCRIPTION Address When Full Feature is selected in the NAT field, configure address mapping sets in Mapping Set menu 15.1. Select one of the NAT server sets (2-10) in menu 15.2 (see Network Address Translation (NAT) When SUA Only is selected in the NAT field, the SMT uses NAT server set 1 in menu 15.2 (see...
Page 149: Remote Node Filter
Figure 76 Sample IP Addresses for a TCP/IP LAN-to-LAN Connection 18.4 Remote Node Filter Move the cursor to the Edit Filter Sets field in menu 11.1, then press [SPACE BAR] to select Yes. Press [ENTER] to display Menu 11.5 – Remote Node Filter. Use Menu 11.5 –...
Page 150: Web Configurator Internet Security Filter Rules
Prestige 660RU-Tx Series User’s Guide Figure 78 Menu 11.5 Remote Node Filter (PPPoA or PPPoE Encapsulation) 18.4.1 Web Configurator Internet Security Filter Rules In the web configurator, open the Security screen as shown next. Select the predefined filter rules and click Apply. Figure 79 Internet Security Once you apply the filter rules in the web configurator, filter sets 11 and 12 are automatically applied in the protocol filters field under Input Filter Sets in SMT menu 11.5.
Page 151: Web Configurator Filter Sets
18.4.2 Web Configurator Filter Sets When you apply filter rules using the web configurator, filter sets 11 and 12 are automatically generated in SMT menu 21. This feature is not available on all models. Figure 80 Menu 21 Filer Set Configuration Filter Set # ------...
Page 152: Editing Atm Layer Options
Prestige 660RU-Tx Series User’s Guide Figure 82 Menu 21.12 WebSet 12 # A Type - - ---- ----------------------------------------------------------- - - - 1 Y IP Pr=6, SA=0.0.0.0, DA=0.0.0.0, DP=23 2 Y IP Pr=6, SA=0.0.0.0, DA=0.0.0.0, DP=21 3 Y IP Pr=17, SA=0.0.0.0, DA=0.0.0.0, DP=69 4 Y IP Pr=6, SA=0.0.0.0, DA=0.0.0.0, DP=80 18.5 Editing ATM Layer Options...
Page 153: Llc-Based Multiplexing Or Ppp Encapsulation
Figure 83 Menu 11.6 for VC-based Multiplexing VC Options for IP: VPI #= 8 VCI #= 35 ATM QoS Type= UBR Peak Cell Rate (PCR)= 0 Sustain Cell Rate (SCR)= 0 Maximum Burst Size (MBS)= 0 Press ENTER to Confirm or ESC to Cancel: 18.5.2 LLC-based Multiplexing or PPP Encapsulation For LLC-based multiplexing or PPP encapsulation, one VC carries multiple protocols with protocol identifying information being contained in each packet header.
Page 154: Figure 85 Menu 11.1 Remote Node Profile
Prestige 660RU-Tx Series User’s Guide Figure 85 Menu 11.1 Remote Node Profile Menu 11.1 - Remote Node Profile Rem Node Name= MyISP Active= Yes Encapsulation= PPPoE Multiplexing= LLC-based Service Name= Incoming: Rem Login= Rem Password= ******** Outgoing: My Login= ? My Password= ? Authen= CHAP/PAP Press ENTER to Confirm or ESC to Cancel:...
Page 155: Chapter 19 Static Route Setup
This chapter shows how to setup IP static routes. 19.1 IP Static Route Overview Static routes tell the Prestige routing information that it cannot learn automatically through other means. This can arise in cases where RIP is disabled on the LAN or a remote network is beyond the one that is directly connected to a remote node.
Page 156: Figure 88 Menu 12 Static Route Setup
Prestige 660RU-Tx Series User’s Guide Figure 88 Menu 12 Static Route Setup 2 From menu 12, select 1 to open Menu 12.1 — IP Static Route Setup (shown next). Figure 89 Menu 12.1 IP Static Route Setup Enter selection number: 3 Now, type the route number of a static route you want to configure.
Page 157: Table 46 Menu12.1.1 Edit Ip Static Route
The following table describes the fields for Menu 12.1.1 – Edit IP Static Route Setup. Table 46 Menu12.1.1 Edit IP Static Route FIELD Route # Route Name Active Destination IP Address IP Subnet Mask Gateway IP Address Metric Private When you have completed this menu, press [ENTER] at the prompt “ or ESC to Cancel: Chapter 19 Static Route Setup Prestige 660RU-Tx Series User’s Guide...
Page 158 Prestige 660RU-Tx Series User’s Guide Chapter 19 Static Route Setup...
Page 159: Chapter 20 Bridging Setup
This chapter shows you how to configure the bridging parameters of your Prestige. 20.1 Bridging in General Bridging bases the forwarding decision on the MAC (Media Access Control), or hardware address, while routing does it on the network layer (IP) address. Bridging allows the Prestige to transport packets of network layer protocols that it does not route, for example, SNA, from one network to another.
Page 160: Figure 91 Menu 11.1 Remote Node Profile
Prestige 660RU-Tx Series User’s Guide Figure 91 Menu 11.1 Remote Node Profile Rem Node Name= ? Active= Yes Encapsulation= ENET ENCAP Multiplexing= VC-based Service Name= N/A Incoming: Rem Login= N/A Rem Password= N/A Outgoing: My Login= N/A My Password= N/A Authen= N/A Press ENTER to Confirm or ESC to Cancel: 3 Move the cursor to the Edit IP/Bridge field, then press [SPACE BAR] to set the value to...
Page 161: Bridge Static Route Setup
Table 47 Remote Node Network Layer Options: Bridge Fields (continued) FIELD Edit IP/Bridge (menu 11.1) Press [SPACE BAR] to select Yes and press [ENTER] to display menu Ethernet Addr Timeout (min.) (menu 11.3) 20.2.2 Bridge Static Route Setup Similar to network layer static routes, a bridging static route tells the Prestige the route to a node before a connection is established.
Page 162 Prestige 660RU-Tx Series User’s Guide Chapter 20 Bridging Setup...
Page 163: Network Address Translation (Nat)
Network Address Translation This chapter discusses how to configure NAT on the Prestige. 21.1 SUA (Single User Account) Versus NAT SUA (Single User Account) is a ZyNOS implementation of a subset of NAT that supports two types of mapping, Many-to-One and Server. See description of the NAT set for SUA.
Page 164: Figure 94 Menu 4 Applying Nat For Internet Access
Prestige 660RU-Tx Series User’s Guide Figure 94 Menu 4 Applying NAT for Internet Access Menu 4 - Internet Access Setup Press ENTER to Confirm or ESC to Cancel: The following figure shows how you apply NAT to the remote node in menu 11.1. 1 Enter 11 from the main menu.
Page 165: Nat Setup
Table 49 Applying NAT in Menus 4 & 11.3 FIELD DESCRIPTION Press [SPACE BAR] and then [ENTER] to select Full Feature if you have multiple public WAN IP addresses for your Prestige. The SMT uses the address mapping set that you configure and enter in the Address Mapping Set field (see section).
Page 166: Sua Address Mapping Set
Prestige 660RU-Tx Series User’s Guide Figure 97 Menu 15.1 Address Mapping Sets Menu 15.1 - Address Mapping Sets Enter Menu Selection Number: 21.3.1.1 SUA Address Mapping Set Enter 255 to display the next screen (see also section). The fields in this menu cannot be changed. Figure 98 Menu 15.1.255 SUA Address Mapping Rules Menu 15.1.255 - Address Mapping Rules Set Name= SUA...
Page 167: User-Defined Address Mapping Sets
Table 50 SUA Address Mapping Rules (continued) FIELD DESCRIPTION Local End IP Local End IP is the ending local IP address (ILA). If the rule is for all local IPs, then the Start IP is 0.0.0.0 and the End IP is 255.255.255.255. Global Start IP This is the starting global IP address (IGA).
Page 168: Ordering Your Rules
Prestige 660RU-Tx Series User’s Guide 21.3.1.3 Ordering Your Rules Ordering your rules is important because the Prestige applies the rules in the order that you specify. When a rule matches the current packet, the Prestige takes the corresponding action and the remaining rules are ignored. If there are any empty rules before your new configured rule, your configured rule will be pushed up by that number of empty rules.
Page 169: Configuring A Server Behind Nat
Figure 100 Menu 15.1.1.1 Editing/Configuring an Individual Rule in a Set Menu 15.1.1.1 Address Mapping Rule Press ENTER to Confirm or ESC to Cancel: The following table explains the fields in this menu. Table 52 Menu 15.1.1.1 Editing/Configuring an Individual Rule in a Set FIELD DESCRIPTION Type...
Page 170: Figure 101 Menu 15.2 Nat Server Setup
Prestige 660RU-Tx Series User’s Guide Figure 101 Menu 15.2 NAT Server Setup Menu 15.2 - NAT Server Sets 3 Enter 1 to go to Menu 15.2.1 NAT Server Setup as follows. Figure 102 Menu 15.2.1 NAT Server Setup Rule Start Port No. --------------------------------------------------- Default Press ENTER to Confirm or ESC to Cancel:...
Page 171: General Nat Examples
Figure 103 Multiple Servers Behind NAT Example 21.5 General NAT Examples The following are some examples of NAT configuration. 21.5.1 Example 1: Internet Access Only In the following Internet access example, you only need one rule where your ILAs (Inside Local addresses) all map to one dynamic IGA (Inside Global Address) assigned by your ISP.
Page 172: Example 2: Internet Access With An Inside Server
Prestige 660RU-Tx Series User’s Guide Figure 105 Menu 4 Internet Access & NAT Example From menu 4, choose the SUA Only option from the Network Address Translation field. This is the Many-to-One mapping discussed in Only read-only option from the Network Address Translation field in menus 4 and 11.3 is specifically pre-configured to handle this case.
Page 173: Example 3: Multiple Public Ip Addresses With Inside Servers
Figure 107 Menu 15.2.1 Specifying an Inside Server Menu 15.2.1 - NAT Server Setup (Used for SUA Only) Rule Start Port No. --------------------------------------------------- 21.5.3 Example 3: Multiple Public IP Addresses With Inside Servers In this example, there are 3 IGAs from our ISP. There are many departments but two have their own FTP server.
Page 174: Figure 108 Nat Example 3
Prestige 660RU-Tx Series User’s Guide Figure 108 NAT Example 3 In this case you need to configure Address Mapping Set 1 from Menu 15.1 - Address Mapping Sets. Therefore you must choose the Full Feature option from the Network Address Translation field (in menu 4 or menu 11.3) in 1 Enter 15 from the main menu.
Page 175: Figure 110 Example 3: Menu 15.1.1.1
Figure 110 Example 3: Menu 15.1.1.1 Menu 15.1.1.1 Address Mapping Rule Press ENTER to Confirm or ESC to Cancel: Figure 111 Example 3: Final Menu 15.1.1 Set Name= Example3 Local Start IP -------------- 1. 192.168.1.10 192.168.1.11 3. 0.0.0.0 Action= Edit Press ENTER to Confirm or ESC to Cancel: Now configure the IGA3 to map to our web server and mail server on the LAN.
Page 176: Example 4: Nat Unfriendly Application Programs
Prestige 660RU-Tx Series User’s Guide Figure 112 Example 3: Menu 15.2.1 Rule Start Port No. --------------------------------------------------- Press ENTER to Confirm or ESC to Cancel: 21.5.4 Example 4: NAT Unfriendly Application Programs Some applications do not support NAT Mapping using TCP or UDP port address translation. In this case it is better to use Many-to-Many No Overload mapping as port numbers do not change for Many-to-Many No Overload (and One-to-One) NAT mapping types.
Page 177: Figure 114 Example 4: Menu 15.1.1.1 Address Mapping Rule
Figure 114 Example 4: Menu 15.1.1.1 Address Mapping Rule Menu 15.1.1.1 Address Mapping Rule Press ENTER to Confirm or ESC to Cancel: After you’ve configured your rule, you should be able to check the settings in menu 15.1.1 as shown next. Figure 115 Example 4: Menu 15.1.1 Address Mapping Rules Set Name= Example4 Local Start IP...
Page 178 Prestige 660RU-Tx Series User’s Guide Chapter 21 Network Address Translation (NAT)
Page 179: Chapter 22 Filter Configuration
This chapter shows you how to create and apply filters. 22.1 About Filtering Your Prestige uses filters to decide whether or not to allow passage of a data packet and/or to make a call. There are two types of filter applications: data filtering and call filtering. Filters are subdivided into device and protocol filters, which are discussed later.
Page 180: The Filter Structure Of The Prestige
Prestige 660RU-Tx Series User’s Guide Figure 117 Filter Rule Process Fetch Next Filter Set Next Filter Set Available? Drop Packet You can apply up to four filter sets to a particular port to block various types of packets. Because each filter set can have up to six rules, you can have a maximum of 24 rules active for a single port.
Page 181: Configuring A Filter Set For The Prestige
22.2 Configuring a Filter Set for the Prestige To configure a filter set, follow the steps shown next. 1 Enter 21 in the main menu to display Menu 21 – Filter Set Configuration as shown next. Figure 118 Menu 21 Filter Set Configuration Filter Set # ------...
Page 182: Filter Rules Summary Menus
Prestige 660RU-Tx Series User’s Guide Figure 120 NetBIOS_LAN Filter Rules Summary Menu 21.1.3 - Filter Rules Summary # A Type - - ---- ------------------------------------------------------------- - - 1 Y IP Pr=17, SA=0.0.0.0, SP=137, DA=0.0.0.0, DP=53 Enter Filter Rule Number (1-6) to Configure: 22.3 Filter Rules Summary Menus The following tables briefly describe the abbreviations used in menus 21.1.1 and 21.1.2.
Page 183: Configuring A Filter Rule
The protocol dependent filter rules abbreviation are listed as follows: Table 54 Rule Abbreviations Used FILTER TYPE DESCRIPTION Protocol Source Address Source Port Number Destination Address Destination Port Number Offset Length 22.4 Configuring a Filter Rule To configure a filter rule, type its number in Menu 21.x – Filter Rules Summary and press [ENTER] to open menu 21.x.1 for the rule.
Page 184: Figure 121 Menu 21.X.1 Tcp/Ip Filter Rule
Prestige 660RU-Tx Series User’s Guide Figure 121 Menu 21.x.1 TCP/IP Filter Rule The following table describes how to configure your TCP/IP filter rule. Table 55 Menu 21.x.1 TCP/IP Filter Rule FIELD DESCRIPTION Filter # This is the filter set, filter rule coordinates, for instance, 2, 3 refers to the second filter set and the third filter rule of that set.
Page 185 Table 55 Menu 21.x.1 TCP/IP Filter Rule (continued) FIELD DESCRIPTION Port # Type the source port of the packets you want to filter. The range of this field is 0 to 65535. A 0 field is ignored. Port # Comp Select the comparison to apply to the source port in the packet against the value given in Source: Port # field.
Page 186: Generic Filter Rule
Prestige 660RU-Tx Series User’s Guide Figure 122 Executing an IP Filter Packet into IP Filter Filter Active? Apply SrcAddrMask to Src Addr Check Src IP Addr Matched Apply DestAddrMask to Dest Addr Check Dest IP Addr Matched Check IP Protocol Matched Check Src &...
Page 187: Figure 123 Menu 21.5.1 Generic Filter Rule
To configure a generic rule select an empty filter set in menu 21, for example 5. Select Generic Filter Rule in the Filter Type field and press [ENTER] to open Menu 21.5.1 – Generic Filter Rule, as shown in the following figure. Figure 123 Menu 21.5.1 Generic Filter Rule Menu 21.5.1 - Generic Filter Rule Filter #: 5,1...
Page 188: Filter Types And Nat
Prestige 660RU-Tx Series User’s Guide Table 56 Menu 21.1.5.1 Generic Filter Rule (continued) FIELD DESCRIPTION Action Not Select the action for a packet not matching the rule. Choices are Check Next Rule, Matched Forward or Drop. When you have completed this menu, press [ENTER] at the prompt “ or ESC to Cancel: 22.5 Filter Types and NAT There are two classes of filter rules, Generic Filter Device rules and Protocol Filter (TCP/IP)
Page 189: Figure 125 Sample Telnet Filter
Figure 125 Sample Telnet Filter 1 Enter 21 in the main menu to display Menu 21 — Filter Set Configuration. 2 Enter the index number of the filter set you want to configure (in this case 6) 3 Type a descriptive name or comment in the Edit Comments field (for example, TELNET_WAN) and press [ENTER].
Page 190: Figure 126 Menu 21.6.1 Sample Filter
Prestige 660RU-Tx Series User’s Guide Figure 126 Menu 21.6.1 Sample Filter Menu 21.6.1 - TCP/IP Filter Rule Filter #: 6,1 Filter Type= TCP/IP Filter Rule Active= Yes IP Protocol= 6 Destination: IP Addr= 0.0.0.0 Source: IP Addr= 0.0.0.0 TCP Estab= No More= No Action Matched= Drop Action Not Matched= Forward...
Page 191: Applying Filters And Factory Defaults
22.7 Applying Filters and Factory Defaults This section shows you where to apply the filter(s) after you design it (them). Sets of factory default filter rules have been configured in menu 21 (but have not been applied) to filter traffic. Table 57 Filter Sets Table FILTER SETS DESCRIPTION...
Page 192: Figure 129 Filtering Remote Node Traffic
Prestige 660RU-Tx Series User’s Guide Figure 129 Filtering Remote Node Traffic Menu 11.5 - Remote Node Filter Enter here to CONFIRM or ESC to CANCEL: Note that call filter sets are visible when you select PPPoA or PPPoE encapsulation. Input Filter Sets: protocol filters= 3 device filters= Output Filter Sets:...
Page 193: Chapter 23 Snmp Configuration
This chapter explains SNMP Configuration menu 22. 23.1 About SNMP Simple Network Management Protocol (SNMP) is a protocol used for exchanging management information between network devices. SNMP is a member of the TCP/IP protocol suite. Your Prestige supports SNMP agent functionality, which allows a manager station to manage and monitor the Prestige through the network.
Page 194: Supported Mibs
Prestige 660RU-Tx Series User’s Guide The managed devices contain object variables/managed objects that define each piece of information to be collected about a device. Examples of variables include the number of packets received, node port status etc. A Management Information Base (MIB) is a collection of managed objects.
Page 195: Snmp Traps
The following table describes the SNMP configuration parameters. Table 58 Menu 22 SNMP Configuration FIELD SNMP: Get Community Set Community Trusted Host Trap: Community Destination When you have completed this menu, press [ENTER] at the prompt “ or ESC to Cancel: 23.4 SNMP Traps The Prestige will send traps to the SNMP manager when any one of the following events occurs:...
Page 196: Table 60 Ports And Permanent Virtual Circuits
Prestige 660RU-Tx Series User’s Guide The port number is its interface index under the interface group. Table 60 Ports and Permanent Virtual Circuits PORT PVC (PERMANENT VIRTUAL CIRCUIT) Ethernet LAN … … xDSL Chapter 23 SNMP Configuration...
Page 197: System Information And Diagnosis
System Information and This chapter covers the information and diagnostic tools in SMT menus 24.1 to 24.4. 24.1 Overview These tools include updates on system status, port status, log and trace capabilities and upgrades for the system software. This chapter describes how to use these tools in detail. Type 24 in the main menu to open Menu 24 –...
Page 198: Figure 133 Menu 24.1 System Maintenance : Status
Prestige 660RU-Tx Series User’s Guide The following table describes the fields present in Menu 24.1 — System Maintenance — Status which are read-only and meant for diagnostic purposes. Figure 133 Menu 24.1 System Maintenance : Status Node-Lnk Status 1-PPPoE Idle My WAN IP (from ISP): 0.0.0.0 Ethernet: Status: 100M/Full Duplex Tx Pkts: 23216...
Page 199: System Information
Table 61 Menu 24.1 System Maintenance : Status (continued) FIELD DESCRIPTION This shows statistics for the WAN. Line Status This shows the current status of the xDSL line, which can be Up or Down. Upstream This shows the upstream transfer rate in kbps. Speed Downstream This shows the downstream transfer rate in kbps.
Page 200: Console Port Speed
Menu 1 – General Setup. Refers to the routing protocol used. Refers to the ZyNOS (ZyXEL Network Operating System) system firmware version. ZyNOS is a registered trademark of ZyXEL Communications Corporation. Displays the vendor of the ADSL chipset and DSL version.
Page 201: Log And Trace
Figure 136 Menu 24.2.2 System Maintenance : Change Console Port Speed Menu 24.2.2 – System Maintenance – Change Console Port Speed Press ENTER to Confirm or ESC to Cancel: 24.4 Log and Trace There are two logging facilities in the Prestige. The first is the error logs and trace records that are stored locally.
Page 202: Syslog And Accounting
Prestige 660RU-Tx Series User’s Guide Figure 138 Sample Error and Information Messages 52 Sat Jan 01 00:00:00 2000 PP12 53 Sat Jan 01 00:00:00 2000 PP00 54 Sat Jan 01 00:00:00 2000 PP00 -WARN 55 Sat Jan 01 00:00:00 2000 PP00 56 Sat Jan 01 00:00:00 2000 PP00 57 Sat Jan 01 00:00:00 2000 PP1c 58 Sat Jan 01 00:00:00 2000 PP0a...
Page 203: Figure 140 Syslog Example
Table 63 Menu 24.3.2 System Maintenance : Syslog and Accounting PARAMETER DESCRIPTION Types: Call Detail Record (CDR) logs all data phone line activity if set to Yes. Packet Triggered The first 48 bytes or octets and protocol type of the triggering packet is sent to the UNIX syslog server when this field is set to Yes.
Page 204: Diagnostic
Prestige 660RU-Tx Series User’s Guide Figure 140 Syslog Example (continued) Jul 19 11:28:39 192.168.102.2 ZYXEL: Packet Trigger: Protocol=1, Data=4500003c100100001f010004c0a86614ca849a7b08004a5c020001006162636465666768696a6b6c 6d6e6f7071727374 Jul 19 11:28:56 192.168.102.2 ZYXEL: Packet Trigger: Protocol=1, Data=4500002c1b0140001f06b50ec0a86614ca849a7b0427001700195b3e00000000600220008cd40000 020405b4 Jul 19 11:29:06 192.168.102.2 ZYXEL: Packet Trigger: Protocol=1, Data=45000028240140001f06ac12c0a86614ca849a7b0427001700195b451d1430135004000077600000 3 - Filter Log SdcmdSyslogSend (SYSLOG_FILLOG, SYSLOG_NOTICE, String);...
Page 205: Figure 141 Menu 24.4 System Maintenance : Diagnostic
Figure 141 Menu 24.4 System Maintenance : Diagnostic Menu 24.4 - System Maintenance - Diagnostic xDSL Reset xDSL TCP/IP 12. Ping Host Enter Menu Selection Number: Host IP Address= N/A The following table describes the diagnostic tests available in menu 24.4 for and the connections.
Page 206 Prestige 660RU-Tx Series User’s Guide Chapter 24 System Information and Diagnosis...
Page 207: Firmware And Configuration File Maintenance
Firmware and Configuration File This chapter tells you how to backup and restore your configuration file as well as upload new firmware and configuration files. 25.1 Filename Conventions The configuration file (often called the romfile or rom-0) contains the factory default settings in the menus such as password, DHCP Setup, TCP/IP Setup, etc.
Page 208: Backup Configuration
Prestige 660RU-Tx Series User’s Guide The following table is a summary. Please note that the internal filename refers to the filename on the Prestige and the external filename refers to the filename not on the Prestige, that is, on your computer, local network or FTP site and so the name (but not the extension) may vary. After uploading new firmware, see the ZyNOS F/W Version field in Menu 24.2.1 –...
Page 209: Using The Ftp Command From The Command Line
Figure 142 Telnet in Menu 24.5 Menu 24.5 - System Maintenance - Backup Configuration To transfer the configuration file to your workstation, follow the procedure below: 1. Launch the FTP client on your workstation. 2. Type "open" and the IP address of your Prestige. Then type "root" and SMT password as requested.
Page 210: Gui-Based Ftp Clients
Prestige 660RU-Tx Series User’s Guide Figure 143 FTP Session Example 331 Enter PASS command Password: 230 Logged in ftp> bin 200 Type I OK ftp> get rom-0 zyxel.rom 200 Port command okay 150 Opening data connection for STOR ras 226 File received OK ftp: 16384 bytes sent in 1.10Seconds 297.89Kbytes/sec.
Page 211: Backup Configuration Using Tftp
25.2.6 Backup Configuration Using TFTP The Prestige supports the up/downloading of the firmware and the configuration file using TFTP (Trivial File Transfer Protocol) over LAN. Although TFTP should work over WAN as well, it is not recommended. To use TFTP, your computer must have both telnet and TFTP clients. To backup the configuration file, follow the procedure shown next.
Page 212: Restore Configuration
Prestige 660RU-Tx Series User’s Guide Table 67 General Commands for GUI-based TFTP Clients COMMAND DESCRIPTION Host Enter the IP address of the Prestige. 192.168.1.1 is the Prestige’s default IP address when shipped. Send/Fetch Use “Send” to upload the file to the Prestige and “Fetch” to back up the file on your computer.
Page 213: Restore Using Ftp Session Example
Figure 144 Telnet into Menu 24.6 Menu 24.6 -- System Maintenance - Restore Configuration To transfer the firmware and configuration file to your workstation, follow the procedure below: 1. Launch the FTP client on your workstation. 2. Type "open" and the IP address of your Prestige. Then type "root" and SMT password as requested.
Page 214: Uploading Firmware And Configuration Files
Prestige 660RU-Tx Series User’s Guide 25.4 Uploading Firmware and Configuration Files This section shows you how to upload firmware and configuration files. You can upload configuration files by following the procedure in following the instructions in Menu 24.7.2 – System Maintenance – Upload System Configuration File.
Page 215: Ftp File Upload Command From The Dos Prompt Example
Figure 147 Telnet Into Menu 24.7.2 System Maintenance Menu 24.7.2 - System Maintenance - Upload System Configuration File To upload the system configuration file, follow the procedure below: 1. Launch the FTP client on your workstation. 2. Type "open" and the IP address of your system. Then type "root" and SMT password as requested.
Page 216: Ftp Session Example Of Firmware File Upload
Prestige 660RU-Tx Series User’s Guide 25.4.4 FTP Session Example of Firmware File Upload Figure 148 FTP Session Example of Firmware File Upload 331 Enter PASS command Password: 230 Logged in ftp> bin 200 Type I OK ftp> put firmware.bin ras 200 Port command okay 150 Opening data connection for STOR ras 226 File received OK...
Page 217: Tftp Upload Command Example
25.4.6 TFTP Upload Command Example The following is an example TFTP command: tftp [-i] host put firmware.bin ras where “ ” specifies binary image transfer mode (use this mode when transferring binary files), “ ” is the Prestige’s IP address and “ host –...
Page 218 Prestige 660RU-Tx Series User’s Guide Chapter 25 Firmware and Configuration File Maintenance...
Page 219: Chapter 26 System Maintenance
System Maintenance. A list of valid commands can be found by typing help or ? at the command prompt. Type “ Figure 149 Command Mode in Menu 24 Enter Menu Selection Number: Figure 150 Valid Commands Copyright (c) 1994 - 2004 ZyXEL Communications Corp. ras> ? Valid commands are: exit bridge ras>...
Page 220: Call Control Support
Prestige 660RU-Tx Series User’s Guide 26.2 Call Control Support Call Control Support is only applicable when Encapsulation is set to PPPoE in menu 4 or menu 11.1. The budget management function allows you to set a limit on the total outgoing call time of the Prestige within certain times.
Page 221: Time And Date Setting
The total budget is the time limit on the accumulated time for outgoing calls to a remote node. When this limit is reached, the call will be dropped and further outgoing calls to that remote node will be blocked. After each period, the total budget is reset. The default for the total budget is 0 minutes and the period is 0 hours, meaning no budget control.
Page 222: Resetting The Time
Prestige 660RU-Tx Series User’s Guide Figure 154 Menu 24.10 System Maintenance: Time and Date Setting Menu 24.10 - System Maintenance - Time and Date Setting Use Time Server when Bootup= None Time Server Address= N/A Current Time: New Time (hh:mm:ss): Current Date: New Date (yyyy-mm-dd): Time Zone= GMT...
Page 223 Prestige 660RU-Tx Series User’s Guide The Prestige resets the time in three instances: • On leaving menu 24.10 after making changes. • When the Prestige starts up, if there is a timeserver configured in menu 24.10. • 24-hour intervals after starting. Chapter 26 System Maintenance...
Page 224 Prestige 660RU-Tx Series User’s Guide Chapter 26 System Maintenance...
Page 225: Chapter 27 Remote Management
This chapter covers remote management (SMT menu 24.11). 27.1 Remote Management Overview Remote management allows you to determine which services/protocols can access which Prestige interface (if any) from which computers. 27.2 Remote Management To disable remote management of a service, select Disable in the corresponding Server Access field.
Page 226: Remote Management Limitations
Prestige 660RU-Tx Series User’s Guide Figure 155 Menu 24.11 Remote Management Control Menu 24.11 - Remote Management Control TELNET Server: Server Port = 23 Secured Client IP = 0.0.0.0 FTP Server: Server Port = 21 Secured Client IP = 0.0.0.0 Web Server: Server Port = 80 Secured Client IP = 0.0.0.0...
Page 227: Remote Management And Nat
27.3 Remote Management and NAT When NAT is enabled: • Use the Prestige’s WAN IP address when configuring from the WAN. • Use the Prestige’s LAN IP address when configuring from the LAN. 27.4 System Timeout There is a default system management idle timeout of five minutes (three hundred seconds). The Prestige automatically logs you out if the management session remains idle for longer than this timeout period.
Page 228 Prestige 660RU-Tx Series User’s Guide Chapter 27 Remote Management...
Page 229: Chapter 28 Ip Policy Routing
This chapter covers setting and applying policies used for IP routing. 28.1 IP Policy Routing Overview Traditionally, routing is based on the destination address only and the IAD takes the shortest path to forward a packet. IP Routing Policy (IPPR) provides a mechanism to override the default routing behavior and alter the packet forwarding based on the policy defined by the network administrator.
Page 230: Ip Routing Policy Setup
Prestige 660RU-Tx Series User’s Guide • routing the packet to a different gateway (and hence the outgoing interface). • setting the TOS and precedence fields in the IP header. IPPR follows the existing packet filtering facility of RAS in style and in implementation. The policies are divided into sets, where related policies are grouped together.
Page 231: Figure 157 Menu 25.1 Ip Routing Policy Setup
Figure 157 Menu 25.1 IP Routing Policy Setup Menu 25.1 - IP Routing Policy Setup - - --------------------------------------------------------------------- 1 Y SA=1.1.1.1-1.1.1.1 DA=2.2.2.2-2.2.2.5 SP=20-20 DP=20-20 P=6 T=NM PR=0 2 N _____________________________________________________________________ _____________________________________________________________________ 3 N _____________________________________________________________________ _____________________________________________________________________ 4 N _____________________________________________________________________ _____________________________________________________________________ 5 N _____________________________________________________________________ _____________________________________________________________________ 6 N _____________________________________________________________________ _____________________________________________________________________...
Page 232: Figure 158 Menu 25.1.1 Ip Routing Policy
Prestige 660RU-Tx Series User’s Guide Figure 158 Menu 25.1.1 IP Routing Policy Policy Set Name= test Active= Yes Criteria: IP Protocol Type of Service= Normal Precedence Source: addr start= 1.1.1.1 port start= 20 Destination: addr start= 2.2.2.2 port start= 20 Action= Matched Gateway addr Type of Service= Max Thruput...
Page 233: Applying An Ip Policy
Table 72 Menu 25.1.1 IP Routing Policy (continued) FIELD Gateway addr Type of Service Precedence When you have completed this menu, press [ENTER] at the prompt “ or ESC to Cancel: 28.5 Applying an IP Policy This section shows you where to apply the IP policies after you design them. 28.5.1 Ethernet IP Policies From Menu 3 —...
Page 234: Ip Policy Routing Example
Prestige 660RU-Tx Series User’s Guide Figure 159 Menu 3.2 TCP/IP and DHCP Ethernet Setup Menu 3.2 - TCP/IP and DHCP Setup Press ENTER to Confirm or ESC to Cancel: Go to menu 11.3 (shown next) and type the number(s) of the IP Routing Policy set(s) as appropriate.
Page 235: Figure 161 Example Of Ip Policy Routing
Route 1 represents the default IP route and route 2 represents the configured IP route. Figure 161 Example of IP Policy Routing To force packets coming from clients with IP addresses of 192.168.1.33 to 192.168.1.64 to be routed to the Internet via the WAN port of the Prestige, follow the steps as shown next. 1 Create a routing policy set in menu 25.
Page 236: Figure 163 Ip Routing Policy Example 2
Prestige 660RU-Tx Series User’s Guide 3 Check Menu 25.1 — IP Routing Policy Setup to see if the rule is added correctly. 4 Create another policy set in menu 25. 5 Create a rule in menu 25.1 for this set to route packets from any host ( means any host) with protocol TCP and port FTP access through another gateway (192.168.1.100).
Page 237: Figure 164 Applying Ip Policies Example
Figure 164 Applying IP Policies Example Menu 3.2 - TCP/IP and DHCP Ethernet Setup Press ENTER to Confirm or ESC to Cancel: Chapter 28 IP Policy Routing Prestige 660RU-Tx Series User’s Guide DHCP Setup DHCP= Server Client IP Pool Starting Address= 192.168.1.33 Size of Client IP Pool= 64 Primary DNS Server= 0.0.0.0 Secondary DNS Server= 0.0.0.0...
Page 238 Prestige 660RU-Tx Series User’s Guide Chapter 28 IP Policy Routing...
Page 239: Chapter 29 Call Scheduling
Call scheduling (applicable for PPPoA or PPPoE encapsulation only) allows you to dictate when a remote node should be called and for how long. 29.1 Introduction The call scheduling feature allows the Prestige to manage a remote node and dictate when a remote node should be called and for how long.
Page 240: Figure 166 Menu 26.1 Schedule Set Setup
Prestige 660RU-Tx Series User’s Guide To setup a schedule set, select the schedule set you want to setup from menu 26 (1-12) and press [ENTER] to see Menu 26.1 — Schedule Set Setup as shown next. Figure 166 Menu 26.1 Schedule Set Setup Menu 26.1 Schedule Set Setup Press ENTER to Confirm or ESC to Cancel: If a connection has been already established, your Prestige will not drop it.
Page 241: Figure 167 Applying Schedule Set(S) To A Remote Node (Pppoe)
Table 73 Menu 26.1 Schedule Set Setup (continued) FIELD DESCRIPTION Action Forced On means that the connection is maintained whether or not there is a demand call on the line and will persist for the time period specified in the Duration field. Forced Down means that the connection is blocked whether or not there is a demand call on the line.
Page 242 Prestige 660RU-Tx Series User’s Guide Chapter 29 Call Scheduling...
Page 243: Chapter 30 Troubleshooting
This chapter covers potential problems and the corresponding remedies. 30.1 Problems Starting Up the Prestige Table 74 Troubleshooting the Start-Up of Your Prestige PROBLEM CORRECTIVE ACTION None of the Make sure that the Prestige’s power adaptor is connected to the Prestige and plugged LEDs turn on in to an appropriate power source.
Page 244: Problems With The Dsl Led
Prestige 660RU-Tx Series User’s Guide 30.3 Problems with the DSL LED Table 76 Troubleshooting the DSL LED PROBLEM CORRECTIVE ACTION The DSL LED is Check the telephone wire and connections between the Prestige DSL port and the off. wall jack. Make sure that the telephone company has checked your phone line and set it up for DSL service.
Page 245: Problems With Internet Access
30.6 Problems with Internet Access Table 79 Troubleshooting Internet Access PROBLEM CORRECTIVE ACTION I cannot access Make sure the Prestige is turned on and connected to the network. the Internet. If the DSL LED is off, refer to Verify your WAN settings. Refer to the chapter on WAN setup (web configurator) or the section on Internet Access (SMT).
Page 246: Problems With The Web Configurator
Prestige 660RU-Tx Series User’s Guide 30.8 Problems with the Web Configurator Table 81 Troubleshooting the Web Configurator PROBLEM CORRECTIVE ACTION I cannot access Refer to the Quick Start Guide for hardware connections. the web Make sure that there is not an SMT console session running. configurator.
Page 247: Splitters And Microfilters
This appendix tells you how to install a POTS splitter or a telephone microfilter. Connecting a POTS Splitter When you use the Full Rate (G.dmt) ADSL standard, you can use a POTS (Plain Old Telephone Service) splitter to separate the telephone and ADSL signals. This allows simultaneous Internet access and telephone service on the same line.
Page 248: Prestige With Isdn
Prestige 660RU-Tx Series User’s Guide 1 Connect a phone cable from the wall jack to the single jack end of the Y- Connector. 2 Connect a cable from the double jack end of the Y-Connector to the “wall side” of the microfilter.
Page 249: Setting Up Your Computer's Ip Address
Setting up Your Computer’s IP Address All computers must have a 10M or 100M Ethernet adapter card and TCP/IP installed. Windows 95/98/Me/NT/2000/XP, Macintosh OS 7 and later operating systems and all versions of UNIX/LINUX include the software components you need to install and use TCP/ IP on your computer.
Page 250: Installing Components
Prestige 660RU-Tx Series User’s Guide Figure 171 WIndows 95/98/Me: Network: Configuration Installing Components The Network window Configuration tab displays a list of installed components. You need a network adapter, the TCP/IP protocol and Client for Microsoft Networks. If you need the adapter: 1 In the Network window, click Add.
Page 251: Configuring
3 Select Microsoft from the list of manufacturers. 4 Select Client for Microsoft Networks from the list of network clients and then click 5 Restart your computer so the changes you made take effect. Configuring 1 In the Network window Configuration tab, select your network adapter's TCP/IP entry and click Properties 2 Click the IP Address tab.
Page 252: Verifying Settings
Prestige 660RU-Tx Series User’s Guide Figure 173 Windows 95/98/Me: TCP/IP Properties: DNS Configuration 4 Click the Gateway tab. • • 5 Click OK to save and close the TCP/IP Properties window. 6 Click OK to close the Network window. Insert the Windows CD if prompted. 7 Turn on your Prestige and restart your computer when prompted.
Page 253: Figure 174 Windows Xp: Start Menu
Figure 174 Windows XP: Start Menu 2 For Windows XP, click Network Connections. For Windows 2000/NT, click Network and Dial-up Connections. Figure 175 Windows XP: Control Panel 3 Right-click Local Area Connection and then click Properties. Appendix B Prestige 660RU-Tx Series User’s Guide...
Page 254: Figure 176 Windows Xp: Control Panel: Network Connections: Properties
Prestige 660RU-Tx Series User’s Guide Figure 176 Windows XP: Control Panel: Network Connections: Properties 4 Select Internet Protocol (TCP/IP) (under the General tab in Win XP) and click Properties. Figure 177 Windows XP: Local Area Connection Properties 5 The Internet Protocol TCP/IP Properties window opens (the General tab in Windows XP).
Page 255: Figure 178 Windows Xp: Advanced Tcp/Ip Settings
• Figure 178 Windows XP: Advanced TCP/IP Settings 6 If you do not know your gateway's IP address, remove any previously installed gateways in the IP Settings tab and click OK. Do one or more of the following if you want to configure additional IP addresses: •...
Page 256: Verifying Settings
Prestige 660RU-Tx Series User’s Guide • • Figure 179 Windows XP: Internet Protocol (TCP/IP) Properties 8 Click OK to close the Internet Protocol (TCP/IP) Properties window. 9 Click OK to close the Local Area Connection Properties window. 10Turn on your Prestige and restart your computer (if prompted). Verifying Settings 1 Click Start, All Programs, Accessories and then Command Prompt.
Page 257: Figure 180 Macintosh Os 8/9: Apple Menu
Figure 180 Macintosh OS 8/9: Apple Menu 2 Select Ethernet built-in from the Connect via list. Figure 181 Macintosh OS 8/9: TCP/IP 3 For dynamically assigned settings, select Using DHCP Server from the Configure: list. Appendix B Prestige 660RU-Tx Series User’s Guide...
Page 258: Verifying Settings
Prestige 660RU-Tx Series User’s Guide 4 For statically assigned settings, do the following: • • • • 5 Close the TCP/IP Control Panel. 6 Click Save if prompted, to save changes to your configuration. 7 Turn on your Prestige and restart your computer (if prompted). Verifying Settings Check your TCP/IP properties in the TCP/IP Control Panel window.
Page 259: Verifying Settings
Figure 183 Macintosh OS X: Network 4 For statically assigned settings, do the following: • • • • 5 Click Apply Now and close the window. 6 Turn on your Prestige and restart your computer (if prompted). Verifying Settings Check your TCP/IP properties in the Network window. Appendix B Prestige 660RU-Tx Series User’s Guide From the Configure box, select Manually.
Page 260 Prestige 660RU-Tx Series User’s Guide Appendix B...
Page 261: Ip Subnetting
IP Addressing Routers “route” based on the network number. The router that delivers the data packet to the correct destination host uses the host ID. IP Classes An IP address is made up of four octets (eight bits), written in dotted decimal notation, for example, 192.168.1.1.
Page 262: Subnet Masks
Prestige 660RU-Tx Series User’s Guide Since the first octet of a class “A” IP address must contain a “0”, the first octet of a class “A” address can have a value of 0 to 127. Similarly the first octet of a class “B” must begin with “10”, therefore the first octet of a class “B”...
Page 263: Example: Two Subnets
Since the mask is always a continuous number of ones beginning from the left, followed by a continuous number of zeros for the remainder of the 32 bit mask, you can simply specify the number of ones instead of writing the value of each octet. This is usually specified by writing a “/”...
Page 264: Table 88 Subnet 1
Prestige 660RU-Tx Series User’s Guide Divide the network 192.168.1.0 into two separate subnets by converting one of the host ID bits of the IP address to a network number bit. The “borrowed” host ID bit can be either “0” or “1” thus giving two subnets;...
Page 265: Example: Four Subnets
Example: Four Subnets The above example illustrated using a 25-bit subnet mask to divide a class “C” address space into two subnets. Similarly to divide a class “C” address into four subnets, you need to “borrow” two host ID bits to give four possible combinations of 00, 01, 10 and 11. The subnet mask is 26 bits (11111111.11111111.11111111.11000000) or 255.255.255.192.
Page 266: Example Eight Subnets
Prestige 660RU-Tx Series User’s Guide Table 93 Subnet 4 IP Address IP Address (Binary) Subnet Mask (Binary) Subnet Address: 192.168.1.192 Broadcast Address: 192.168.1.255 Example Eight Subnets Similarly use a 27-bit mask to create 8 subnets (001, 010, 011, 100, 101, 110). The following table shows class C IP address last octet values for each subnet.
Page 267: Subnetting With Class A And Class B Networks
Subnetting With Class A and Class B Networks. For class “A” and class “B” addresses the subnet mask also determines which bits are part of the network number and which are part of the host ID. A class “B” address has two host ID octets available for subnetting and a class “A” address has three host ID octets (see Table The following table is a summary for class “B”...
Page 268 Prestige 660RU-Tx Series User’s Guide Appendix C...
Page 269: Appendix Dpppoe
PPPoE in Action An ADSL modem bridges a PPP session over Ethernet (PPP over Ethernet, RFC 2516) from your computer to an ATM PVC (Permanent Virtual Circuit) which connects to a DSL Access Concentrator where the PPP session terminates number of PPP sessions from your LAN. PPPoE provides access control and billing functionality in a manner similar to dial-up services using PPP.
Page 270: How Pppoe Works
Prestige 660RU-Tx Series User’s Guide Figure 184 Single-Computer per Router Hardware Configuration How PPPoE Works The PPPoE driver makes the Ethernet appear as a serial link to the computer and the computer runs PPP over it, while the modem bridges the Ethernet frames to the Access Concentrator (AC).
Page 271: Virtual Circuit Topology
ATM is a connection-oriented technology, meaning that it sets up virtual circuits over which end systems communicate. The terminology for virtual circuits is as follows: • Virtual Channel Logical connections between ATM switches • Virtual Path A bundle of virtual channels •...
Page 272 Prestige 660RU-Tx Series User’s Guide Appendix E...
Page 273: Appendix F Command Interpreter
The following describes how to use the command interpreter. Enter 24 in the main menu to bring up the system maintenance menu. Enter 8 to go to Menu 24.8 - Command Interpreter Mode. See the included disk or zyxel.com for more detailed information on these commands. Note: Use of undocumented commands or misconfiguration can damage the unit and possibly render it unusable.
Page 274 Prestige 660RU-Tx Series User’s Guide Appendix F...
Page 275: Appendix G Log Descriptions
This appendix provides descriptions of example log messages. Table 97 System Maintenance Logs LOG MESSAGE Time calibration is successful Time calibration failed WAN interface gets IP: %s DHCP client IP expired DHCP server assigns %s Successful SMT login SMT login failed Successful WEB login WEB login failed Successful TELNET login...
Page 276: Table 98 System Error Logs
Prestige 660RU-Tx Series User’s Guide Table 98 System Error Logs LOG MESSAGE %s exceeds the max. number of session per host! setNetBIOSFilter: calloc error readNetBIOSFilter: calloc error WAN connection is down. Table 99 Packet Filter Logs LOG MESSAGE [ TCP | UDP | ICMP | IGMP | Generic ] packet filter matched (set: %d, rule: %d) Table 100 ICMP Logs...
Page 277: Table 102 Ppp Logs
Table 101 CDR Logs (continued) LOG MESSAGE board %d line %d channel %d, call %d, %s C02 OutCall Connected %d %s board %d line %d channel %d, call %d, %s C02 Call Terminated Table 102 PPP Logs LOG MESSAGE ppp:LCP Starting ppp:LCP Opening ppp:CHAP Opening ppp:IPCP Starting The PPP connection’s Internet Protocol Control Protocol stage is starting.
Page 278: Table 104 Syslog Logs
Prestige 660RU-Tx Series User’s Guide Table 103 ICMP Notes (continued) TYPE CODE Table 104 Syslog Logs LOG MESSAGE <Facility*8 + Severity>Mon dd hr:mm:ss hostname src="<srcIP:srcPort>" dst="<dstIP:dstPort>" msg="<msg>" note="<note>" devID="<mac address last three numbers>" cat="<category> The following table shows RFC-2408 ISAKMP payload types that the log displays. Please refer to the RFC for detailed information on each type.
Page 279 Table 105 RFC-2408 ISAKMP Payload Types (continued) LOG DISPLAY CER_REQ HASH NONCE NOTFY Appendix G Prestige 660RU-Tx Series User’s Guide PAYLOAD TYPE Key Exchange Identification Certificate Certificate Request Hash Signature Nonce Notification Delete Vendor ID...
Page 280 Prestige 660RU-Tx Series User’s Guide Appendix G...
Page 281: Index
Address Assignment Address mapping Address Resolution Protocol (ARP) ADSL, what is it? ADSLstandards Alternative Subnet Mask Notation Any IP 31, 59 How it works note Any IP Setup Any IP table applicaions Internet access AT command ATM Adaptation Layer 5 (AAL5) ATM layer options Authentication Authentication protocol...
Page 282 Prestige 660RU-Tx Series User’s Guide Diagnostic Tools Domain Name 57, 79 domain name Domain Name System DSL (Digital Subscriber Line) DSL line, reinitialize DSL, What Is It? DSLAM (Digital Subscriber Line Access Multiplexer) Dynamic DNS 32, 86, 125 dynamic DNS 32, 126 Dynamic Host Configuration Protocol DYNDNS Wildcard...
Page 283 Interactive Applications Internet Access 31, 35, 136, 139, 140 Internet access 42, 136 Internet Access Setup 162, 243 Internet access wizard setup Internet Assigned Numbers AuthoritySee IANA IP Address 44, 58, 78, 111, 134, 156, 160, 183, 199, 204, 230 IP Address Assignment ENET ENCAP PPPoA or PPPoE...
Page 284 Prestige 660RU-Tx Series User’s Guide NNTP Packet Error Received Transmitted Packet Triggered Packets Password 54, 118, 122, 144, 193 password 118, 244 Peak Cell Rate (PCR) 65, 68 Ping Point to Point Protocol over ATM Adaptation Layer 5 (AAL5) Point-to-Point Point-to-Point Tunneling Protocol policy-based routing POP3...
Page 285 SMT Menu Overview SMTP SNMP Community Configuration GetNext Manager MIBs Trap Trusted Host SOHO (Small Office/Home Office) Source-Based Routing Splitters Static route Static Routing Topology 77, 79 SUA (Single User Account) 77, 162 SUA server 78, 80 Default server set SUA vs NAT SUA/NAT Server Set Subnet Mask...
Page 286 Prestige 660RU-Tx Series User’s Guide WAN (Wide Area Network) WAN backup WAN Setup Web Configurator 38, 39, 40 web configurator screen summary web service XMODEM protocol Zero Configuration Internet Access ZyNOS ZyNOS (ZyXEL Network Operating System) ZyNOS F/W Version ZyXEL Limited Warranty Note...

This manual is also suitable for:

Prestige 660ru P-660ru-t1 P-660ru-t3 P-660ru-t7 Prestige 660ru-t series

ZyXEL Communications ADSL2+ Ethernet/USB Gateway 660RU-Tx Series User Manual

Chapter 1 Getting to Know Your Prestige

Chapter 2 Introducing the Web Configurator

Chapter 3 Wizard Setup

Chapter 4 Password Setup

Chapter 5 LAN Setup

Chapter 6 WAN Setup

Chapter 7 Network Address Translation (NAT) Screens

Chapter 8 Dynamic DNS Setup

Chapter 9 Time and Date

Chapter 10 Remote Management Configuration

Chapter 11 Universal Plug-And-Play (Upnp)

Chapter 12 Maintenance

Chapter 13 Introducing the SMT

Chapter 14 Menu 1 General Setup

Chapter 15 Menu 2 WAN Backup Setup

Chapter 16 Menu 3 LAN Setup

Chapter 17 Internet Access

Chapter 18 Remote Node Configuration

Quick Links

Troubleshooting

Related Manuals for ZyXEL Communications ADSL2+ Ethernet/USB Gateway 660RU-Tx Series

Summary of Contents for ZyXEL Communications ADSL2+ Ethernet/USB Gateway 660RU-Tx Series