York Sun Premier GZA1M Series Start-Up & Operation page 103

Table 32: BACnet Points List (Continued)
BACnet
Object
Attributes
Type
MOAFlow-Sp AV
Fr Air AV
LowSpeedFan-
AV
MinPos
MornWRAT-Sp AV
EconDampPos AV
RAH AV
EVAP-T AV
LoadShedAdjust AV
Altitude AV
MornCRAT-Sp AV
EarlyStrtPeriod AV
DeviceId AV
UnoccDehumSP AV
SZVAVMinFanSpd AV
EconAlrmDly AV
EconPosErr AV
EconMinErr AV
StgClgCmd AV
StgHtgCmd AV
PropHtgCmd AV
YORK
Object Read/
Short Description
ID Write
29795 R/W MOAFlow-Sp
29796 R Fr Air
LowSpeedFan-
29808 R/W
MinPos
29823 R/W MornWRAT-Sp
29824 R EconDampPos
29828 R RAH
C1-
29833 R
EvapTempValue
29885 R/W LoadShedAdjust
29889 R/W Altitude
29892 R/W MornCRAT-Sp
29895 R/W EarlyStrtPeriod
29897 R/W DeviceId
HGRUnoccHum-
29903 R/W
SP
29913 R/W SZVAVMinFanSpd
29916 R/W EconAlrmDly
29917 R/W EconPosErr
29918 R/W EconMinErr
29922 R StgClgCmd
29923 R StgHtgCmd
29924 R PropHtgCmd
Start-Up & Operation Guide | 5587001-YSG-A-520
Long
Point Definitions (Units)
Description
Min Outside A BAS command to adjust minimum
Airflow Setpoint outside airflow setpoint (0–5,000 CFM)
Fresh Air Intake Displays the fresh air (outside air)
Value intake value (CFM)
Economizer
A BAS command to adjust
Damper Minimum
economizer damper minimum
Position Low
position for low speed fan (0–100%)
Speed Fan
Morning Warm- A BAS command to adjust morning
up/RAT Setpoint warm-up/RAT setpoint (50.0–85.0°F)
Economizer The economizer damper position
Damper Position feedback (%)
Return Air Displays the active return air humidity
Humidity (%RH)
Evaporating
Displays the active temperature of
Temperature
the air leaving the evaporator (°F)
Value Circuit 1
A BAS command to adjust load shed
Load Shed Adjust for automatic demand response (0–8
Δ°F)
A BAS command to adjust the
Altitude
altitude (-1,500 to 30,000 feet)
Morning Cool
A BAS command to adjust morning
Down/RAT
cool down/RAT setpoint (50–85°F)
Setpoint
A BAS command to adjust early start
Early Start Period
period (0–120 minutes)
A BAS command to input device
Device OID
object ID (0–4194302)
HGRH UNOCC A BAS command to adjust HGRH
Humidity Setpoint UNOCC humidity setpoint (0-100%)
SZVAV Minimum A BAS command to adjust the SZVAV
Fan Speed minimum fan speed (20–67%)
A BAS command to adjust
FDD Economizer
economizer FDD alarm delay
Alarm Delay
(1–3,600 seconds)
FDD Economizer A BAS command to adjust the outside
Damper Allowed air damper feedback versus actual
Error position error tolerance (0–100%)
FDD Damper A BAS command to adjust the outside
Min Position air damper feedback versus actual
Tolerance position tolerance in error (0–10%)
Staged Cooling
Displays the cooling command (%)
Command
Staged Heating
Displays the heating command (%)
Command
Proportional Displays the proportional heating
Heating command for all modulating heat
Command options (%)
103