Page 1 EMV1200 FHD / EMV800 FHD 12CH/8CH Hybrid Mobile DVR User’s Manual Copyright © EverFocus Electronics Corp. Release Date: August, 2020...
Page 2 All rights reserved. No part of the contents of this manual may be reproduced or transmitted in any form or by any means without written permission of the EverFocus Electronics Corporation. Windows is a registered trademark of the Microsoft Corporation.
Page 3 Safety Precautions  Refer all work related to the installation of this product to qualified service personnel or system installers.  Do not block the ventilation openings or slots on the cover.  Do not drop metallic parts through slots. This could permanently damage the appliance. Turn the power off immediately and contact qualified service personnel for service.
Page 4 Follow Instructions  All operating and use instructions should be followed. Cleaning  Unplug the unit from the outlet before cleaning. Do not use liquid cleaners, abrasive or aerosol cleaners. Use a damp cloth for cleaning. Attachments  Do not use attachments not recommended by the product manufacturer as they may cause hazards.
Page 5 This Product is RoHS compliant. Your EverFocus product is designed and manufactured with high quality materials and components which can be recycled and reused. This symbol means that electrical and...
Page 6: Table Of Contents
TABLE OF CONTENTS Introduction ........................1 Features .......................... 3 Packing List ........................3 Optional Accessories ....................... 4 Front Panel ........................5 Rear Panel ........................7 Getting Started ......................9 Installation ........................9 2.1.1 Mounting ........................10 Hard Disk Installation ....................11 SD Card Installation .......................
Page 7 3.1.1 How to Select a Channel / Enable Audio Out ............36 3.1.2 OSD Root Menu ......................37 3.1.3 Field Input Options....................37 General Operation ......................39 3.2.1 Login .......................... 39 3.2.2 Forget Your Password ....................40 3.2.3 Audio Selection ......................41 OSD Root Menu ......................
Page 8 6.1.5.1 eZ Controller (Control Camera OSD Setting from DVR End) ......72 Record ........................... 73 Event ..........................74 6.3.1 Alarm ......................... 74 6.3.2 Video Loss ......................... 77 6.3.3 G Sensor ........................79 6.3.4 GPS ..........................80 6.3.5 Other ......................... 81 Storage ..........................
Page 9 Menu Bar........................128 7.3.1 Event ........................129 7.3.1.1 Alarm ......................129 7.3.1.2 Video Loss .......................... 132 7.3.1.3 GPS Event .......................... 134 7.3.1.4 G-Sensor Event ......................... 135 7.3.1.5 Other ........................... 136 7.3.2 Storage ........................144 7.3.2.1 Storage ..........................144 7.3.2.2 SD Card ..........................
Page 10 Specifications ......................185 EMV800 FHD ....................... 185 EMV1200 FHD ......................187 Troubleshooting ......................189 Appendix A: Network Overview ..................190 Appendix B: Linksys & D-Link Port Forwarding ..............194 Appendix C: Timing of Alarm Modes .................. 198 Appendix D: IR Remote Control ..................201 Appendix E: RTSP URL Syntax ....................
Page 11: Introduction
The EMV800 FHD / EMV1200 FHD can support both of analog (AHD/TVI/SD) and IP cameras, delivering up to 1080p (analog) and up to 4MP (IP) image quality.
Page 12 Power Output *Analog SD/HD * The EMV800 FHD / EMV1200 FHD have 4 power output sets (+/-) to power-up the connected cameras. A total of 12VDC, 5A power output is provided. Please refer to 2.5.2 Video Cable / Power- Out Cable for more details.
Page 13: Features
IR Remote Control (with two AAA batteries. See Note 4) x 1 • Power Harness Cable x 1 • Video Cable x 3 (EMV1200 FHD); x2 (EMV800 FHD) (see 2.5.2 Video Cable / Power-Out Cable) • Audio Cable x 1 (see 2.5.3 Audio Cable) •...
Page 14: Optional Accessories
Note: 1. Equipment configurations and supplied accessories vary by country. Please consult your local EverFocus office or agents for more information. Please also keep the shipping carton for possible future use. 2. Contact the shipper if any items appear to have been damaged in the shipping process.
Page 15: Front Panel
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 1.4 Front Panel EMV800 FHD / EMV1200 FHD No. Name Description Lock to power on the HDD. After locking the HDD Tray Lock (No.2), lock the HDD Power Lock to power on the HDD. The HDD power indicator will light in blue to indicate the HDD power is on.
Page 16 EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR • Alarm: Turns on when the connected alarm I/O is triggered; turns off when the alarm I/O stops being triggered. • GPS: Turns on continuously when the mobile DVR is receiving GPS data.
Page 17: Rear Panel
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 1.5 Rear Panel EMV800 FHD EMV1200 FHD 9-12 CH No. Name Description By default, this port is set to a Main monitor output. Connects to a Main monitor using a VGA cable.
Page 18 EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR D-Sub connector for connecting to the Alarm I/O, RS-232 (CAN bus) D-Sub Connector or RS-485 devices (such as analog PTZ cameras). For details, please refer to 2.5.4 D-Sub Cable. M12 connector for connecting to IP cameras. For details, please Ethernet Port (LAN) refer to 2.5.5 Ethernet Cable.
Page 19: Getting Started
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR Chapter 2. Getting Started 2.1 Installation Before installation, choose a location in the vehicle where it can: • Provide convenient access for installing or removing the hard disk • Allow air to flow around the device. Inadequate or improper air flow can impede proper...
Page 20: Mounting
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 2.1.1 Mounting You can mount the mobile DVR onto a surface inside the vehicle. Please note that to meet the EN50155 and the SAE-J1455 standard for the mobile DVR, the Bracket on the MDVR is required to be used.
Page 21: Hard Disk Installation
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 2.2 Hard Disk Installation You can insert a 2.5” HDD (up to 2TB) or SSD (up to 4TB) into the HDD tray for video recording. Please follow the steps below. Note: 1. The mobile DVR does not support hot swap for the hard disk. Ensure to power off the mobile DVR before removing the hard disk.
Page 22 EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 4. Insert a HDD in the HDD Tray and then screw the HDD to the tray with the supplied 4 screws. 5. Insert the HDD Tray into the drive bay and close the Locking Arm until you hear a click sound.
Page 23: Sd Card Installation
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 2.3 SD Card Installation The mobile DVRs provide SD card function for Alarm event backup recording. Please follow the steps below to install the SD Card. Up to 128 GB SD / SDHC cards are supported. You can also download the Storage Compatibility Table from the product page (click Download) to see the tested card brands.
Page 24 EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR After installing the SD Card, it’s recommended to enable the Record Overwrite function. The Record Overwrite function enables the mobile DVR to overwrite the recordings when the card space is full. If Record Overwrite is not enabled, the alarm event backup recording to the SD card will stop when card space is full.
Page 25: Vehicle Connection
/ truck with 12 VDC / 24 VDC. * The following figures are using EMV1200 FHD for example; the differences between the two models are the numbers of video input and audio input.
Page 26: Connecting To A Car With 12 Vdc
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 2.4.2 Connecting to a Car with 12 VDC Glove box (inside or underneath) Trunk Passenger seat (underneath) Driver seat (between the seat and side panel) EMV1200 FHD (Rear Panel) 9-12 CH Power Harness Cable...
Page 27: Basic Connection
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 2.5 Basic Connection After installing the mobile DVR in the vehicle, you can start connecting the mobile DVR to the external devices. The instructions below describe the basic connection to the mobile DVRs. For details on cable connections, please refer to the following sections.
Page 28: Power Harness Cable
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 2.5.1 Power Harness Cable You can connect the mobile DVR to a power source between 9 VDC ~ 36 VDC. (The following figure uses EMV1200 FHD as an example). EMV1200 FHD (Rear Panel) 9-12 CH Power Input...
Page 29: Video Cable / Power-Out Cable
You can use the supplied Video Cables to connect the analog cameras to the MDVR. EMV800 FHD has 2 Video In Ports for connecting to 8 analog cameras; while EMV1200 FHD has 3 Video In Ports for connecting to 12 analog cameras.
Page 30: Audio Cable
Audio Cable. The Audio Cable is labeled with AIN 1~ AIN 12. Please be noted that Microphones with a (built-in) amplifier and external power supply are required. The following figure uses EMV1200 FHD as an example. The EMV1200 FHD provides 12 audio inputs; while the EMV800 FHD provides 8 audio inputs.
Page 31: D-Sub Cable
RS-485_B (-) Note: 1. If you want to connect OBDII or CAN bus, please use RS-232 #1 (D-Sub connector). The OBDII and CAN bus should be the EverFocus approved ones. Please contact EverFocus for more details. ts@everfocus.com.tw 2. For TPMS connection, please use RS-232 #2 (PIN19/PIN20).
Page 32: Ethernet Cable
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 2.5.5 Ethernet Cable The Ethernet Port (M12) on the rear panel can be used to connect to LAN network for connecting to IP cameras. Pin Assignment M12-4P MDI0- MDI1+ MDI0+ MDI1- 2.5.6...
Page 33: Monitor Connection
The two call monitor outputs provide the identical functionality. Make sure that the connected monitor's specifications comply with these resolution requirements. (This figure uses EMV1200 FHD mobile DVR as an example). Front Panel Rear Panel...
Page 34: Turning On / Off The Power
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 2.7 Turning On / Off the Power Before powering on the mobile DVR, please make sure the internal HDD have been installed properly. Once you have completed the basic cable connections, you are ready to turn on the mobile DVR.
Page 35 EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 2. Click the Finish button, the IP Utility will be automatically launched to search the IP devices connected on the same LAN. 3. To access the Live View window, double click the IP address of the desired device, the login window pops up.
Page 36 EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR Note for the first time login: The “Download ePlayer Instruction” page will only be prompted for the first time login in order to update the system to the latest plugin version. When the Plug-in blocked appears on the browser, select Always allow plug-ins on xxx, click Done and then reload the webpage.
Page 37 EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR  If your PC or laptop is running with Windows, it’s required to run the browser as administrator when first entering the remote web page of the device. Go to C:\Program Files (x86)\Internet Explorer, right-click the browser and then click Run as administrator.
Page 38: Connecting The Mobile Dvr To The Network
Once you have a straight through cable plug one end into the LAN port on the back of  the recorder and the other into the router. Log into the EverFocus mobile DVR menu and go to the Network Setting Menu.  To let the router automatically assign an address: ...
Page 39 EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR To manually assign an address: Go to a computer connected on the same network as the mobile DVR.  Click on the Start button and choose Run.  If using Windows Vista, choose Search instead.
Page 40 EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR To set the mobile DVR for Internet Connection through router: The next step is to open ports within your router. Log into the router using a PC and  open the following ports.
Page 41: Direct High-Speed Connection
 the recorder and the other into the high speed modem. Log into the EverFocus mobile DVR menu and go to the Network Setting Menu.  Input the Static IP address, the Subnet Mask, and the Gateway that you obtained from ...
Page 42: One-To-One Connection
 mobile DVR and the other into the network card on the back of the computer. Log into the EverFocus mobile DVR menu and go to the Network Setting Menu.  You must use the Static IP option for this type of connection.
Page 43 EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR Go to Start. Double-click on Control Panel.  Click Network and Sharing Center.  Click Local Area Connection. ...
Page 44 EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR Click Properties.  Click on Internet Protocol Version 4 (TCP/IPv4) and then click Properties. ...
Page 45 EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR Select Use the following IP address. Assign an IP address of 192.168.1.2, a Subnet  Mask of 255.255.255.0, and a Default Gateway of 192.168.1.1 and then click OK. Restart both of the computer and the mobile DVR.
Page 46: General Operation
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR Chapter 3. General Operation There are two ways to control the OSD menu of the mobile DVRs: with a Mouse or the supplied handheld IR Remote Control. For details on the IR remote control, please refer to Appendix D, IR Remote Control.
Page 47: Osd Root Menu
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 3.1.2 OSD Root Menu Right-click the mouse, the OSD Root Menu window appears. Click on any icon to enter its setup menu. Click the button on the top-right corner or right-click to close the OSD Root Menu.
Page 48 EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR Drop-Down Box: Click on the down arrow to see all selections, then directly click on an option to select it. Check Box: Click on the box to enable it (checked) or disable it (unchecked).
Page 49: General Operation
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 3.2 General Operation 3.2.1 Login In order to access mobile DVRs, you may be prompted to log in for authority identification. To log in, follow the steps below: Right click on the screen to display the Root Menu. The following window appears.
Page 50: Forget Your Password
1. If you forget your password, please email the Serial Number of the mobile DVR to ts@everfocus.com.tw , and then EverFocus will send you a verification code. 2. Input this verification code in the Password field of the Login window within 24 hours, and check the Verification Mode box.
Page 51: Audio Selection
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 3.2.3 Audio Selection In order to utilize the audio function, please follow the instructions below before switching on the audio function. Note: The Audio function is unavailable for Germany. 1. Connect the audio devices to the mobile DVR. Note that Speakers/Microphones with a (built-in) amplifier and external power supply are required.
Page 52: Osd Root Menu
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR Chapter 4. OSD Root Menu OSD Overlay No. Name Description Previous / Next Click to turn to the previous or next page. Click to display the PTZ Control Panel for controlling the connected PTZ cameras.
Page 53 EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR Click to switch to the Call monitor settings. Click to switch to the Main monitor settings. After switching to Call monitor, users can only operate the Information, Sequence, Layout, Display, Channel and Main Monitor Call Monitor buttons on the OSD Root Menu;...
Page 54: Ptz
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 4.1 PTZ You can use the PTZ Control Panel to control the connected PTZ (analog/IP speed dome) cameras. Before using this function, please connect the PTZ camera to the system and configure the PTZ settings in advance (please refer to PTZ ID in 6.1.1 Analog Camera).
Page 55: Express Control Of Ptz
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 4.1.1 Express Control of PTZ If the PTZ Control Panel has first been opened and then hidden, the mouse can be used to control basic PTZ functions. Move your mouse cursor on the screen, the mouse cursor will turn into a control icon (direction, focus or zoom) in different areas of the screen.
Page 56: Layout Switching
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 4.2 Layout Switching The mobile DVRs have several screen layout options. Layout options may differ based on different Device Modes and models. DVR/Hybrid Mode NVR Mode To change layout, follow the steps below: 1.
Page 57: Osd Overlay
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 4.4 OSD Overlay You can display system and camera status icons/info on the live view screen. Follow the steps below: 1. You can decide whether to display only the system icons, only the camera icons/info, both of system and camera icons/info;...
Page 58 EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 4. The following icons will be displayed at the bottom of the monitor to show the OBDII / CAN bus status. To enable OBDII / CAN bus status, please consult EverFocus for more details ts@everfocus.com.tw...
Page 59: Sequence
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 4.5 Sequence The sequence function is used to display each channel in sequence order with a pre-setup dwell time. The system will display one channel at a time in full screen. Dwell time of each channel is set up with 3 seconds by default.
Page 60 EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR Right-click the screen, the Zoom Bar appears in the middle of the screen. Click to zoom in the camera view up to 4X. Click the Logout button to log out the Zoom mode.
Page 61: Archiving The Recordings To The Usb Or Ftp
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 4.7 Archiving the Recordings to the USB or FTP You can archive the recordings to the USB storage device or FTP. On the OSD Root Menu, click the Copy icon , the following menu appears.
Page 62 EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR EFPlayer: Unzip the EFPlayer file and double-click to open it as below. The EFPlayer can only display up to 16 channels at one time. No. Name Function Description Shows the recording information of the device, including model of...
Page 63 EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR Click to take a snapshot of the channels displayed on the UI. You Snapshot can save the snapshot file to a desired location. Mute Click to mute; click again to turn off the mute function.
Page 64: Logout
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 4.8 Logout You can log out the mobile DVR by clicking the Exit icon on the OSD Root Menu to bring up the Logout Confirmation window. Click “Yes” when you are ready to logout of the system.
Page 65: Temporarily Logout
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 4.8.1 Temporarily Logout You can temporarily log out the mobile DVR with covert streams (analog cameras) by clicking the Exit icon on the OSD Root Menu. This function is designed for use in conjunction with the Covert Camera function.
Page 66 EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 3. Click the Exit icon on the OSD Root Menu, the Logout Confirmation window appears. 4. Click the Yes button and the selected camera streams will be hidden on the Live View / Sequence Mode.
Page 67: Information
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 4.9 Information You can see the mobile DVR information and Log data on this page. Or export the log data to the USB storage device. 4.9.1 System Info In the System Menu, you can only see the information of the mobile DVR, Network or HDD.
Page 68: Log Info
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 4.9.2 Log Info You can choose, display or export log data using this menu. Start Date / End Date: Click to bring up the on-screen keyboard to set up the start / end date.
Page 69: Search And Playback
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR Chapter 5. Search and Playback You can use the Search functions to search for the desired recordings for playing back. On the OSD Root Menu, click the Playback button to enter the playback search window.
Page 70: Event Search
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 5.2 Event Search Start Date / End Date: Click to bring up the on-screen keyboard to select the start / end date. Start Time / End Time: Click to bring up the on-screen clock to select the start / end time.
Page 71: Playback Bar
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 5.3 Playback Bar Users can use the Playback Bar to play back recordings on the system. After clicking the Play button on the Time Search or Event Search window, the Playback Bar will be displayed on the bottom of the screen.
Page 72: System Configuration
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR Chapter 6. System Configuration The mobile DVRs can be configured through a series of menus on screen by using a Mouse or the supplied IR Remote Control. The following operations are examples of using a Mouse. This chapter describes the functions and options of the System Setting on the on-screen display (OSD) menus.
Page 73 EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR List of Configuration Options: Please find the topic of interest by referring to the section prefixed to each option. 6.1.1 Analog Camera 6.1.2 Add IP Camera 6.1 Camera 6.1.3 IP Camera 6.1.4 Camera Info 6.1.5 Adjust...
Page 74: Camera
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 6.1 Camera You can configure the settings for individual cameras. 6.1.1 Analog Camera Camera: Select a camera to be configured. Title: Click to bring up the on-screen keyboard for assigning a title for the selected camera.
Page 75 EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR Main Stream Sub Stream eZ.HD Camera (1080p): 1920x1080 eZ.HD Camera (720p): 1280x720 352x240 / 176x120 WD1 or D1 Camera: 960x480 / 704x480 / 352x240 Record Quality: Select a recording quality for the Main Stream and Sub Stream. The options include Low, Basic, Standard, High and Superior.
Page 76: Display Aspect Ratio
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 6.1.1.1 Display Aspect Ratio It is recommended to select the same ratio of the screen resolution and the camera live view display to avoid black bars showing on the live view screen shown as images below.
Page 77: Add Ip Camera
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 6.1.2 Add IP Camera You can add IP camera on this page. To automatically add IP cameras: 1. Click the Search button, the IP cameras connected on the same LAN with the system will be displayed on the above table.
Page 78 EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR To manually add IP cameras: 1. Click the Manual button, the Manual Add window appears. 2. Select a channel from the Channel drop-down list. Select a Manufacturer and input the IP Address, TCP Port, User Name and Password.
Page 79: Ip Camera
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 6.1.3 IP Camera You can configure IP camera parameters using the IP Camera window. Once entering this window, the system will automatically get the first IP camera parameters from the device end.
Page 80: Camera Info
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 6.1.4 Camera Info You can view the info of the connected analog cameras and IP cameras. Analog Camera Info IP Camera Info Note: For mobile DVR to automatically get all IP camera parameters, you will have to select each IP camera from the Channel drop-down list on the IP Camera setting window.
Page 81: Adjust
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 6.1.5 Adjust You can adjust some image settings for the analog and IP cameras. Analog Camera IP Camera Camera: Select a camera to adjust the following settings. Dev ice Title: Displays the title of the selected camera.
Page 82: Ez Controller (Control Camera Osd Setting From Dvr End)
Diagram A below. It will take extra effort, time and people to adjust the camera. Now, EverFocus’ eZ.Controller allows users to control the camera OSD simply on the monitor at the DVR end as illustrated in Diagram Use eZ.Controller to Control Camera OSD...
Page 83: Record
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 6.2 Record You can configure the basic record settings on this page. Record Overwrite: Check the box to overwrite the hard disk / SD card when it is full. Note that unless this box is checked, or the mobile DVR will stop recording when the hard disk / SD card is full.
Page 84: Event
Network Alarm: Check the box to send out a network alarm to a client PC when alarm events occur. This feature works with EverFocus’ CMS software. You will need to configure the Alarm Server for the mobile DVR to send network alarms to the client PC (see 6.6.7 Alarm Server).
Page 85 EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR SD Backup: Check the box to enable Alarm event backup recordings to the SD card. When an alarm is triggered, the mobile DVR will record the alarm event to the SD card for 60 seconds start from the triggered time.
Page 86 EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR this field. The alarm will be associated with this camera for full screen display, event logging and PTZ actions. PTZ: If the Active Camera selected above is a PTZ camera, you can further set up the PTZ actions in this field.
Page 87: Video Loss
Network Alarm: Check the box to send out a network alarm to a client PC when video loss event occurs. This feature works with EverFocus’ CMS software. You will need to configure the Alarm Server for the mobile DVR to send network alarms to the client PC (see 6.6.7 Alarm Server).
Page 88 EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR Alarm Output: Select an alarm output number. When an alarm is triggered, the signal will be transmitted through the alarm output relay. Output Type: Select an output type when an alarm is triggered.
Page 89: G Sensor
Network Alarm: Check box to send out a network alarm to the client PC. This feature works with EverFocus’ CMS software. You will need to configure the Alarm Server for mobile DVR to send network alarms to the client PC (see 6.6.7 Alarm Server).
Page 90: Gps
Network Alarm: Check box to send out a network alarm to the client PC. This feature works with EverFocus’ CMS software. You will need to configure the Alarm Server for mobile DVR to send network alarms to the client PC (see 6.6.7 Alarm Server).
Page 91: Other
Network Alarm: Check the box to send out a network alarm to a client PC. This feature works with EverFocus’ CMS software. You will need to configure the Alarm Server for the mobile DVR to send network alarms to the client PC (see 6.6.7 Alarm Server).
Page 92 Network Alarm: Check the box to send out a network alarm to a client PC when storage fails. This feature works with EverFocus’ CMS software. You will need to configure the Alarm Server for the mobile DVR to send network alarms to the client PC (see 6.6.7 Alarm Server).
Page 93 Network Alarm: Check the box to send out a network alarm to a client PC when storage is full. This feature works with EverFocus’ CMS software. You will need to configure the Alarm Server for the mobile DVR to send network alarms to the client PC (see 6.6.7 Alarm Server).
Page 94 Network Alarm: Check the box to send out a network alarm to a client PC when storage is off. This feature works with EverFocus’ CMS software. You will need to configure the Alarm Server for the mobile DVR to send network alarms to the client PC (see 6.6.7 Alarm Server).
Page 95 Network Alarm: Check the box to send out a network alarm to a client PC when Disk Retry Failure occurs. This feature works with EverFocus’ CMS software. You will need to configure the Alarm Server for the mobile DVR to send network alarms to the client PC (see 6.6.7 Alarm Server).
Page 96 Network Alarm: Check the box to send out a network alarm to a client PC when power has been restored. This feature works with EverFocus’ CMS software. You will need to configure the Alarm Server for the mobile DVR to send network alarms to the client PC (see 6.6.7 Alarm Server).
Page 97 EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 6.3.5.7 Network Loss Log: Check the box to record alarm events to log data. Buzzer: Check the box to enable buzzer when network is lost. Alarm Output: Select an alarm output number. When an alarm is triggered, the signal will be transmitted through the selected alarm output relay.
Page 98 Network Alarm: Check the box to send out a network alarm to a client PC when GPS is lost. This feature works with EverFocus’ CMS software. You will need to configure the Alarm Server for the mobile DVR to send network alarms to the client PC (see 6.6.7 Alarm Server).
Page 99: Storage
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 6.4 Storage The Storage menu is used to review the mobile DVR’s hard drive settings and status. 6.4.1 Storage Info The storage information will be displayed here. No value in this menu can be configured by the operator.
Page 100: Sd Card
5% of the card space will be reserved for system use. If you want to back up the recordings, you can use EverFocus EF-Reader to remotely/locally back up the recordings from the SD card (see Appendix F Recording Backup through EF-Reader).
Page 101: Lock/Format
Format Storage Device: Click this button to format the whole HDD. WARNING: This will effectively ERASE the ENTIRE hard disk!! If you want to back up the recordings, you can use EverFocus EF-Reader to locally back up the recordings from the hard disk (see Appendix F Recording Backup through EF-Reader).
Page 102: Display
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 6.5 Display You can configure the settings for displaying system status or a title on the live view image. You can also set up the sequencing order for the Main / Call monitor.
Page 103: Sequence
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 6.5.2 Sequence You can configure up to 20 steps of the sequencing order for the Main / Call monitor. The Sequence function will repeat continuously from step 1 to step 20 until interrupted.
Page 104: Network
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 6.6 Network The mobile DVR allows you to use a Web browser to remotely view and manage the system. You can also receive live video streaming from the mobile DVR using your smart phone.
Page 105 EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR IP address: Displays the mobile DVR’s current IPv4 IP Address. A static IP address must be set manually. If DHCP is selected, this value will be assigned automatically. Subnet Mask: Displays the subnet mask for your network so the mobile DVR will be recognized within the network.
Page 106 EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR DNS Address (depending on your network hardware and IP configuration this may be the IP address of your router/gateway, or it may be the actual IP address of the local DNS server). The DNS server IP is required because your DNS server provides critical information necessary for the mobile DVR to communicate with the DDNS server.
Page 107: Wireless
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 6.6.2 Wireless You can set up the Wi-Fi network on this page. Wireless Mode: Three options are selectable: Disable, Static IP and DHCP. Disable: Select to disable this function. Static IP: User can set a fixed IP for network connection.
Page 108: Mobile
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 6.6.3 Mobile After connecting the 3G / 4G Antenna to the mobile DVR, you have to set up the mobile settings for the mobile DVR to connect to the wireless network. Follow the steps below: 1.
Page 109: Email
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 6.6.4 Email You can configure the Email settings for mobile DVR to send Email alert when an event occurs. SMTP Server: Assign the SMTP (e-mail) server’s name. Note that for more reliable email service, use the server’s IP address.
Page 110: Ddns
Save: Click to save the settings. Note: 1. It is not necessary to append the HTTP port number to the DDNS name. The EverFocus DDNS server not only keeps track of your mobile DVR’s IP address, but also keeps track of the ports.
Page 111 EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR To set up DDNS function: 1. In order to allow remote access to the MDVR from outside of the local network, enable either the Port Forwarding or DMZ function of your router. Please refer to the manual of...
Page 112 ISP service provider. 3. On the DDNS setting page (OSD Root Menu > System > Network > DDNS), register a free host name from EverFocus DDNS and then click the Save button. a. Select EverfocusDDNS from the DDNS Service drop-down list.
Page 113 4. The DDNS setup is now complete. Open a browser and enter the domain name (http://[host name].everfocusddns.com) in the address field. The Web interface of the MDVR should be displayed. For example, if you’ve obtained the host name “HQtest” from EverFocus DDNS server, enter http://HQtest.everfocusddns.com in the address field of the browser.
Page 114 EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 6.6.5.2 www.dyndns.org DDNS Service: Select www.dyndns.org from the drop-down list. Host name: Host name created through the dyndns account. User name: User name of the dyndns account. Password: Password of the dyndns account.
Page 115: Ftp
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 6.6.6 Set up the FTP server settings to enable the FTP function. The function is for users to upload the alarm recordings (MP4) or snapshots (JPEG) from sub stream to the FTP server. You can choose to upload either the recordings or snapshots, please see 6.3.1 Alarm.
Page 116: Alarm Server
6.6.7 Alarm Server You can send out the alarm notifications to EverFocus’s CMS software. Please also consult the CMS’s user manual for network alarm settings. Server IP1~3: IP address of client PC. The network alarm can be transmitted to up to 3 addresses.
Page 117: Remote/Mobile
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 6.6.8 Remote/Mobile You can configure the compression format for the sub-stream for mobile phone access. Select H.264 or MJPEG codec to enable the mobile phone access function. Note that if you also want to use the FTP function for uploading the recordings (MP4 video format), please select the H.264 codec.
Page 118: Network Test
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 6.6.9 Network Test The Ping utility is useful in diagnosing connectivity problems by obtaining responses from nodes progressively farther along the network. DNS functionality can also be confirmed by entering a valid DNS name instead of an IP address.
Page 119: Xfleet
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 6.6.10 Xfleet You can use EverFocus Xfleet2.0 system for fleet management. Xfleet 2.0 is a centralized management platform which is well designed to not only monitor fleets, but also to track driver statistics, maintenance records, fuel statistics and plenty of other in-depth analytics reports that assist you to make decisions and eventually reduce overall costs.
Page 120: Sys Setting
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 6.7 Sys Setting You can configure general settings for the mobile DVR on this page. 6.7.1 Date / Time You can set up the date and time for the mobile DVR. Note: Clicking Save at this page will disable the Daylight Saving function if this function has been enabled.
Page 121 EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR NTP Server: If NTP is selected from the Time Sync drop-down list above, you will have to further select a NTP Server. The NTP Server displays the time server address that the mobile DVR uses for time synchronization.
Page 122: Daylight Saving
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 6.7.2 Daylight Saving You can configure the settings for mobile DVR to automatically adjust to daylight saving time. Note: If this page is grayed out, it means that you have enabled the Auto daylight saving function, please refer to 6.7.1 Date/Time.
Page 123: User Group
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 6.7.3 User Group This setting page is used for configuring the privilege of the three access levels: Administrator, Manager and Operator. Check the boxes under an access level to enable the privileges of that access level.
Page 124 EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR Change Password: • Administrator: The Administrator account has the privilege to change password to all the user accounts. Manager: The Manager account can change password to itself and Operator accounts. Operator: The Operator account can only change its own password.
Page 125: User Management
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 6.7.4 User Management You can create multiple user accounts (max: 20 user accounts) with different privileges. The mobile DVR has default user accounts which you can choose to copy, edit, add or delete, and...
Page 126 EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR You can further configure each user account and its settings individually, see the steps below: 1. Click on a user account. 2. Click the Add, Copy or Edit button, and the following page appears.
Page 127: I/O Control
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 6.7.5 I/O Control You can configure the connected device settings such as RS-232, RS-485 or GPS on this page. Please connect the devices to the system before configuring the I/O Control settings. Please refer to 2.5.4 D-Sub Cable for device connection.
Page 128 EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 【 RS-485 】 PTZ Protocol: Select PTZ protocol, choose from the following protocols: Transparent, Pelco_D, Pelco_P, Everfocus or Samsung. (Note: All cameras on the RS-485 bus must use the same protocol) Type: Select a type.
Page 129: Ekb200 Setting
6.7.6 EKB200 Setting You can connect an EKB200, which is EverFocus’ USB keyboard, to the USB port on the DVR to control the Iris, focus or the pre-configured PTZ control functions of the connected cameras. The control keys on the EKB200...
Page 130 EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR Run Auto Pan: Press this key to start the AutoPan number specified in the Value column.  Stop Auto Pan: Press this key to stop the AutoPan number specified in the Value column.
Page 131: Miscellaneous
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 6.7.7 Miscellaneous You can upgrade the latest firmware, restore the factory default settings to the mobile DVR, upload / save the mobile DVR configuration settings from / to the USB or change the language in this setup menu.
Page 132 EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR Remote Reboot: Check the box to enable restarting the mobile DVR via the Remote Web page. Shutdown: Click the Shutdown button if you need to turn off the mobile DVR. When the message as below pops up on the screen, you can now turn off the mobile DVR.
Page 133: Remote Access To The Mobile Dvr
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR Chapter 7. Remote Access to the Mobile DVR Accessing the Mobile DVR on the Network Follow the steps below to access the mobile DVR from a computer. Open an Internet Explorer window and in the address bar type the IP address.
Page 134 EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR If you log in for the first time, follow the instruction steps on the interface to update the latest Plugin version (ePlayer). After reloading the webpage, the login window pops up again. Type the user ID and password to log in again. By default, the user ID is admin and the password is 11111111.
Page 135 EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR If you encounter the following problem or still can’t access the remote Web interface, please see below:  If the Error window appears, please be sure to close ALL the Web browser windows first then click Retry.
Page 136 EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR  If your PC or laptop is running with Windows, it’s required to run the browser as administrator when first entering the remote web page of the device. Go to C:\Program Files (x86)\Internet Explorer, right-click the browser and then click Run as administrator.
Page 137: Remote Live View
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 7.2 Remote Live View No. Name Description For configuring the mobile DVR. Please refer to 7.3 Menu Bar. Menu Bar Layout Click to select a desired layout. Sub / Main Click to switch between the Main stream and Sub stream.
Page 138: Menu Bar
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 7.3 Menu Bar No. Name Description Live View Click to display the live view window. Click to configure the alarm / event settings. Please refer to 7.3.1 Event. Event Click to display the Storage information. Please refer to 7.3.2 Storage.
Page 139: Event
Network Alarm: Check the box to send out a network alarm to a client PC when an alarm event occurs. This feature works with EverFocus’ CMS software. You will need to configure the Alarm Server for the mobile DVR to send network alarms to the client PC (see 7.3.4.7 Alarm Server).
Page 140 EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR SD Backup: Check the box to enable Alarm event backup recordings to the SD card. When an alarm is triggered, the mobile DVR will record the alarm event to the SD card for 60 seconds start from the triggered time.
Page 141 EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR this field. The alarm will be associated with this camera for full screen display, event logging and PTZ actions. PTZ: If the Active Camera selected above is a PTZ camera, you can further set up the PTZ actions in this field.
Page 142: Video Loss
Network Alarm: Check the box to send out a network alarm to a client PC when video loss event occurs. This feature works with EverFocus’ CMS software. You will need to configure the Alarm Server for the mobile DVR to send network alarms to the client PC (see 7.3.4.7 Alarm Server).
Page 143 EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR Output Type: Select an output type when an alarm is triggered. Timeout: Select this option and then set up the Timeout Duration in the field below, the alarm output will last for the setup duration time (10 ~ 150 seconds).
Page 144: Gps Event
Network Alarm: Check box to send out a network alarm to the client PC. This feature works with EverFocus’ CMS software. You will need to configure the Alarm Server for mobile DVR to send network alarms to the client PC (see 7.3.4.7 Alarm Server).
Page 145: G-Sensor Event
Network Alarm: Check box to send out a network alarm to the client PC. This feature works with EverFocus’ CMS software. You will need to configure the Alarm Server for mobile DVR to send network alarms to the client PC (see 7.3.4.7 Alarm Server).
Page 146: Other
Network Alarm: Check the box to send out a network alarm to a client PC. This feature works with EverFocus’ CMS software. You will need to configure the Alarm Server for the mobile DVR to send network alarms to the client PC (see 7.3.4.7 Alarm Server).
Page 147 Network Alarm: Check the box to send out a network alarm to a client PC when storage fails. This feature works with EverFocus’ CMS software. You will need to configure the Alarm Server for the mobile DVR to send network alarms to the client PC (see 7.3.4.7 Alarm Server).
Page 148 Network Alarm: Check the box to send out a network alarm to a client PC when storage is full. This feature works with EverFocus’ CMS software. You will need to configure the Alarm Server for the mobile DVR to send network alarms to the client PC (see 7.3.4.7 Alarm Server).
Page 149 Network Alarm: Check the box to send out a network alarm to a client PC when storage is off. This feature works with EverFocus’ CMS software. You will need to configure the Alarm Server for the mobile DVR to send network alarms to the client PC (see 7.3.4.7 Alarm Server).
Page 150 Network Alarm: Check the box to send out a network alarm to a client PC when Disk Retry Failure occurs. This feature works with EverFocus’ CMS software. You will need to configure the Alarm Server for the mobile DVR to send network alarms to the client PC (see 7.3.4.7 Alarm Server).
Page 151 Network Alarm: Check the box to send out a network alarm to a client PC when power has been restored. This feature works with EverFocus’ CMS software. You will need to configure the Alarm Server for the mobile DVR to send network alarms to the client PC (see 7.3.4.7 Alarm Server).
Page 152 EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 7.3.1.7 Network Loss Log: Check the box to record alarm events to log data. Buzzer: Check the box to enable buzzer when network is lost. Alarm Output: Select an alarm output number. When an alarm is triggered, the signal will be transmitted through the selected alarm output relay.
Page 153 Network Alarm: Check the box to send out a network alarm to a client PC when GPS is lost. This feature works with EverFocus’ CMS software. You will need to configure the Alarm Server for the mobile DVR to send network alarms to the client PC (see 7.3.4.7 Alarm Server).
Page 154: Storage
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 7.3.2 Storage The Storage menu is used to review the mobile DVR’s storage settings and status. No value in this menu can be configured by the operator. 7.3.2.1 Storage Record Time (Start): Shows the earliest recording time of the mobile DVR.
Page 155: Sd Card
5% of the card space will be reserved for system use. If you want to back up the recordings, you can use EverFocus EF-Reader to remotely/locally back up the recordings from the SD card (see Appendix F Recording Backup through EF-Reader).
Page 156: Lock/Format
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 7.3.2.3 Lock/Format You can control the percentage of the storage space reserved for Locked Event Recordings. You can also format the hard disk if necessary. Maximum Lock (%): Sets the maximum percentage of the hard disk space reserved for Locked Event Recordings.
Page 157: Display Setting
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 7.3.3 Display Setting You can configure the settings for displaying the camera / mobile DVR information on the live view image. You can also set up the sequencing order for the Main / Call monitor.
Page 158: Monitor Sequence
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 7.3.3.2 Monitor Sequence You can configure up to 20 steps of the sequencing order for the Main / Call monitor. The Sequence will repeat continuously from step 1 to step 20 until interrupted.
Page 159: Network
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 7.3.4 Network The mobile DVR allows you to use a Web browser to remotely view and manage the system. You can also receive live video streaming from the mobile DVR using your smart phone.
Page 160 EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR Gateway: Displays the gateway on your network for the mobile DVR to use when communicating with any devices not on the local network. If DHCP is selected, this value will be assigned automatically.
Page 161 EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR to obtain a list of the IP addresses of their recommendation of the best servers to use for your location. 4. If you are connecting through a router, make sure that you have ‘opened up’ all the required network ports in the port forwarding section of your router’s setup options.
Page 162: Wireless
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 7.3.4.2 Wireless You can set up the Wi-Fi network on this page. Wireless Mode: Three options are selectable: Disable, Static IP and DHCP. Disable: Select to disable this function. Static IP: User can set a fixed IP for network connection.
Page 163: Mobile
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 7.3.4.3 Mobile After connecting the 3G / 4G Antenna to the mobile DVR, you have to set up the mobile settings for the mobile DVR to connect to the wireless network. Follow the steps below: 1.
Page 164: Email
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 7.3.4.4 Email You can configure the Email settings for mobile DVR to send Email alert when an event occurs. SMTP Server: Assign the SMTP (e-mail) server’s name. Note that for more reliable email service, use the server’s IP address.
Page 165: Ddns
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 7.3.4.5 DDNS DDNS (Dynamic Domain Name System) is a service used to map a domain name to the dynamic IP address of a network device. You can set up the DDNS service for remote access to the mobile DVR.
Page 166 EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR Note: 1. It is not necessary to append the HTTP port number to the DDNS name. The EverFocus DDNS server not only keeps track of your mobile DVR’s IP address, but also keeps track of the ports.
Page 167 EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR To set up DDNS function: 1. In order to allow remote access to the MDVR from outside of the local network, enable either the Port Forwarding or DMZ function of your router. Please refer to the manual of...
Page 168 If PPPoE is selected: Enter the User Name (e.g. xxxx@hinet.net) and Password  provided by your ISP service provider. 3. On the DDNS setting page, register a free host name from EverFocus DDNS and then click the Save button. a. Select EverfocusDDNS from the DDNS Service drop-down list.
Page 169 4. The DDNS setup is now complete. Open a browser and enter the domain name (http://[host name].everfocusddns.com) in the address field. The Web interface of the MDVR should be displayed. For example, if you’ve obtained the host name “HQtest” from EverFocus DDNS server, enter http://HQtest.everfocusddns.com in the address field of the browser.
Page 170: Ftp
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 7.3.4.6 FTP Set up the FTP server settings to enable the FTP function. The function is for users to upload the alarm recordings (MP4) or snapshots (JPEG) from sub stream to the FTP server. You can choose to upload either the recordings or snapshots, please see 7.3.1 Event.
Page 171: Alarm Server
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 7.3.4.7 Alarm Server You can send out the alarm notifications to EverFocus’s CMS software. Please also consult the CMS’s user manual for network alarm settings. Server IP1~3: IP address of client PC. The network alarm can be transmitted to up to 3 addresses.
Page 172: Remote/Mobile
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 7.3.4.8 Remote/Mobile You can configure the compression format for the sub-stream for mobile phone access. Select H.264 or MJPEG codec to enable the mobile phone access function. Note that if you also want to use the FTP function for uploading the recordings (MP4 video format), please select the H.264 codec.
Page 173: Xfleet
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 7.3.4.9 Xfleet You can use EverFocus Xfleet2.0 system for fleet management. Xfleet 2.0 is a centralized management platform which is well designed to not only monitor fleets, but also to track driver statistics, maintenance records, fuel statistics and plenty of other in-depth analytics reports that assist you to make decisions and eventually reduce overall costs.
Page 174: System Setting
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 7.3.5 System Setting You can configure the general settings for the mobile DVR in this menu. 7.3.5.1 Date/Time You can set up the date and time for the mobile DVR. Note: Clicking Save at this page will disable the Daylight Saving function if this function has been enabled.
Page 175 EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR the NTP server in Taiwan. To find a compatible NTP address of the mobile DVR’s physical location, follow the steps below: a. Use a computer connected to the Network. b. Click Start > Run > type “command” and then click OK.
Page 176: Daylight Saving
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 7.3.5.2 Daylight Saving You can configure the settings for mobile DVR to automatically adjust to daylight saving time. Note: If this page is grayed out, it means that you have enabled the Auto daylight saving function, please refer to 7.3.5.1 Date/Time.
Page 177: User Group
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 7.3.5.3 User Group This setting page is used for configuring the privilege of the three access levels: Administrator, Manager and Operator. Check the boxes under an access level to enable the privileges of that access level.
Page 178 EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR Change Password: • Administrator: The Administrator account has the privilege to change password to all the user accounts. Manager: The Manager account can change password to itself and Operator accounts. Operator: The Operator account can only change its own password.
Page 179: User Management
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 7.3.5.4 User Management You can create multiple user accounts (max: 20 user accounts) with different privileges. The mobile DVR has default user accounts which you can choose to copy, edit, add or delete, and...
Page 180 EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR You can further configure each user account and its settings individually, see the steps below: 1. Click on a user account. 2. Click the Add, Copy or Edit button, and the following page appears.
Page 181: I/O Control
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 7.3.5.5 I/O Control The I/O Control setup menu is used to define the settings for controlling the mobile DVR through RS-485 / RS-232 communication protocol and for mobile DVR to control the connected PTZ cameras.
Page 182 EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 【 RS-485 】 PTZ Protocol: Select PTZ protocol, choose from the following protocols: Transparent, Pelco_D, Pelco_P, Everfocus or Samsung. (Note: All cameras on the RS-485 bus must use the same protocol) Type: Select a type.
Page 183: Ekb200 Setting
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 7.3.5.6 EKB200 Setting You can connect an EKB200, which is EverFocus’ USB keyboard, to the USB port on the DVR to control the Iris, focus or the pre-configured PTZ control functions of the connected cameras.
Page 184 EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 【Key No】 The control key number on the keyboard. 【Action】 Select an item from the drop-down list to define the function for each key on the keyboard. Set Preset: You can use the joystick on the keyboard to select a position and then press ...
Page 185: Miscellaneous
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 7.3.5.7 Miscellaneous You can upgrade the latest firmware, restore the factory default settings to the mobile DVR, upload / save the mobile DVR configuration settings from / to the USB or change the language in this setup menu.
Page 186: Information
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 7.3.6 Information You can see the mobile DVR information and Log data in this menu. Or export the log data to your computer. 7.3.6.1 System In the System Menu, you can only see the information of the mobile DVR, Network or HDD. No configuration can be done in this menu.
Page 187: Log
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 7.3.6.2 Log You can choose, display or export log data using this menu. Start Date / End Date: Click to set up the start / end date. Start Time / End Time: Click to set up the start / end time.
Page 188: Copy
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 7.3.7 Copy You can remotely archive the recordings to your computer. The archived recordings will be stored in .avr format. You can download EFPlayer through this menu to play back the recordings. On the Menu Bar, click the Copy icon , the following menu appears.
Page 189 EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR EFPlayer: Unzip the EFPlayer file and double-click to open it as below. The EFPlayer can only display up to 16 channels at one time. No. Name Function Description Shows the recording information of the device, including model of...
Page 190 EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR Click to take a snapshot of the channels displayed on the UI. You Snapshot can save the snapshot file to a desired location. Mute Click to mute; click again to turn off the mute function.
Page 191: Search
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 7.3.8 Search You can search the recordings for playing back by using the Search menu. 7.3.8.1 Time Search Select the Start Date and Time and then click the Play button to start playing back.
Page 192: Event Search
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 7.3.8.2 Event Search Select the Start/End Date/Time, select the desired cameras, select the desired event types and then click the Search button, the searched list appears. To copy the selected event to your computer or FTP server, select Remote or FTP from the Copy Type drop-down list.
Page 193 EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR Note: 1. If the Archiving Recording to the FTP server is working in progress, the FTP Upload function (refer to 7.3.1.1 Alarm) will stop. The system will start the FTP Upload function when the Archiving Recording to the FTP progress is complete.
Page 194: Ptz
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 7.3.9 You can use the PTZ Control Panel to control the connected PTZ (analog/IP speed dome) cameras. Before using this function, please connect the PTZ camera to the system and configure the PTZ settings in advance (please refer to PTZ ID in 6.1.1 Analog Camera).
Page 195: Specifications
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR Chapter 8. Specifications 8.1 EMV800 FHD Model Name EMV800 FHD Video System NTSC / PAL Video Compression H.264 Hybrid mode: 4 Analog + 4 IP Video Input Composite Video Input DVR mode: 8 Analog...
Page 196 EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR RJ-45 port x 1 (10/100/1000M), M12 port x 1 for IP Ethernet Cameras (10/100M) Network Wi-Fi Yes (Optional) 3G / 4G Yes (Optional) Yes (Optional) 2.5" HDD x 1 (Max. 2TB) or SSD (Max. 4TB) Storage SD/SDHC Card (Max.
Page 197: Emv1200 Fhd
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 8.2 EMV1200 FHD Model Name EMV1200 FHD Video System NTSC / PAL Video Compression H.264 Up to 12CH (Hybrid mode: 8 Analog + 4 IP or Video Input DVR mode: 12 Analog)
Page 198 EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR RJ-45 x 1, RS-232 x 3, RS-485 x 1, USB x 3, USB(M12) External Interface Interfaces x 1, LAN(M12) x 1 G-Sensor 3-Axis G-Sensor embedded System Control IR Remote Control, Mouse, Web UI...
Page 199: Troubleshooting
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR Chapter 9. Troubleshooting If you have problems with the system, run through the following checklist to see if you can solve the problem. The mobile DVR will not go into record mode.
Page 200: Appendix A: Network Overview
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR Appendix Appendix A: Network Overview This chapter will give you a basic instruction on how to set up the mobile DVR for network connection. It is highly recommended that you have a working knowledge of what a network is and how it works.
Page 201 EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR Gateway Address Addressees are either local or remote. A gateway address is composed of four octets separated by decimal points. The gateway address is used to uniquely identify the device on the LAN that has access to the communications links connecting to other LANs, WANs and/or the Internet (access to the ‘remote’...
Page 202 This makes it much simpler to host a website, email server, or other type of server connection. Everfocus suggests using a static IP address. If this is not available, you will need to use a dynamic IP address. This is explained below.
Page 203 EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR Pre-Installation EverFocus’ mobile DVR can operate using one of three types of networking connections. Simple One to One Connection: A simple one to one connection is the simplest type of network connection. It uses a cross-over cable to make a direct connection from one computer to another (or in this case a computer to a mobile DVR).
Page 204: Appendix B: Linksys & D-Link Port Forwarding
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR Appendix Appendix B: Linksys & D-Link Port Forwarding Typical Linksys Port Forwarding This section will cover a few simple configurations for the Linksys router. This chapter is only to offer some help to the installer and end user. Please understand we DO NOT support this product and will not give tech support on it.
Page 205 EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR Click on the “Applications & Gaming” tab. Applications and Gaming allows you to set up public services on your network, such as web servers, ftp servers, e-mail servers, or other specialized Internet applications. (Some Internet applications may not require any forwarding) To forward a port, enter the information on each line for the criteria required.
Page 206 EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR Typical D-Link Port Forwarding This section will cover a few simple configurations for the D-Link router. This chapter is only to offer some help to the installer and end user. Please understand we DO NOT support this product and will not give tech support on it.
Page 207 EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR Click Virtual Servers on the left to bring up the following screen. Virtual Servers allows users who are connecting remotely to access services on the router’s Local Network. The functions of each field are described below.
Page 208: Appendix C: Timing Of Alarm Modes
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR Appendix Appendix C: Timing of Alarm Modes Transparent Mode Input Event Alarm Duration Event = Reaction Duration of alarm input source (contact, system events...) Event : Resulting duration for this alarm mode, related to event record, alarm outputs, OSD...
Page 209 EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR Timeout Mode Input Event Alarm Duration Event Duration = Reaction Duration of alarm input source (contact, system events...) Event : Alarm duration for timeout, defined in the event setup menus Duration : Resulting duration for this alarm mode, related to event record, alarm outputs, OSD...
Page 210 EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR Timeout Mode: Retrigger of Alarms Duration of alarm input source (contact, system events...) Event : Alarm duration for timeout, defined in the event setup menus Duration : Resulting duration for this alarm mode, related to event record, alarm outputs, OSD...
Page 211: Appendix D: Ir Remote Control
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR Appendix Appendix D: IR Remote Control The IR remote control is an accessory to enhance the convenient operation of the mobile DVR. You can perform all the settings and operations from the remote control. The effective distance is up to 33 feet line of sight.
Page 212: Appendix E: Rtsp Url Syntax
Appendix Appendix E: RTSP URL Syntax EverFocus provides 2 / 4 / 8 / 12 / 16 / 32 channels DVR, NVR or Mobile DVRs. The RTSP URL Syntax of EverFocus’ DVR, NVR and Mobile DVR are listed as below:...
Page 213 EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 8CH DVR / NVR / MDVR: rtsp://[device-ip-address]/3GPP/[channel-number 0~7] * [device-ip-address] is the IP address of the DVR/NVR/MDVR Main Stream * [channel-number 0~7] is the channel number of the DVR/NVR/MDVR. 0 for channel 1, 1 for channel 2, and so on.
Page 214 EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR 32CH DVR / NVR: rtsp://[device-ip-address]/3GPP/[channel-number 0~31] * [device-ip-address] is the IP address of the DVR/NVR Main Stream * [channel-number 0~31] is the channel number of the DVR/NVR. 0 for channel 1, 1 for channel 2, and so on.
Page 215: Appendix F: Recording Backup Through Ef-Reader
Appendix Appendix F: Recording Backup through EF-Reader EverFocus EF-Reader is an enhanced HDD reader enabling users to access HDDs / SD cards locally or remotely and further play back the recordings. Users granted with privileges are allowed to log in the EF-Reader and operate the specific functions. The EF-Reader supports AVI, MP4 and AVR file formats.
Page 216: Appendix G: Auto Hdd Retry Mechanism
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR Appendix Appendix G: Auto HDD Retry Mechanism The eZ.HD DVR/MDVR features Auto HDD Retry mechanism, which is designed to automatically reboot to detect the installed HDDs when encounter HDD fail error. Note: The Auto HDD Retry mechanism will only activate when all of the HDDs installed in the DVR/MDVR are failed simultaneously.
Page 217 FAX: +81 3 5820-1018 sales@everfocus.com www.everfocus.co.jp info@everfocus.co.jp Ihr EverFocus Produkt wurde entwickelt Your EverFocus product is designed and und hergestellt mit qualitativ manufactured with high quality materials hochwertigen Materialien und and components which can be recycled Komponenten, die recycelt und wieder and reused.

This manual is also suitable for:

Emv800 fhd

EverFocus EMV1200 FHD User Manual

1 Introduction

2 Getting Started

3 General Operation

4 OSD Root Menu

5 Search and Playback

6 System Configuration

7 Remote Access to the Mobile DVR

8 Specifications

9 Troubleshooting

Appendix A: Network Overview

Appendix B: Linksys & D-Link Port Forwarding

Appendix C: Timing of Alarm Modes

Appendix D: IR Remote Control

Appendix E: RTSP URL Syntax

Appendix F: Recording Backup through EF-Reader

Appendix G: Auto HDD Retry Mechanism

Quick Links

Related Manuals for EverFocus EMV1200 FHD

Summary of Contents for EverFocus EMV1200 FHD

This manual is also suitable for:

Table of Contents