Labels & Cosmetics - Grizzly G0834 Owner's Manual

501
DANGER!
ROTATING
CUTTERHEAD BELOW!
WARNING! WARNING!
KICKBACK HAZARD! ALWAYS USE
1. Ensure outfeed table is PUSH BLOCKS!
Do not operate machine
even with knives.
Push blocks minimize the
with guard removed! 2. Never exceed the
possibility of operator's
Cutterhead contact will
maximum depth of cut.
hands contacting the
cause serious personal
3. Do not stand directly
injury. cutterhead while cutting.
behind workpiece.
513
WARNING!
INJURY HAZARD!
To reduce risk of short
and long-term injury,
wear safety glasses,
512
hearing protection, and
a respirator when using
this machine.
511
WARNING!
To reduce risk of death
or serious injury, read
manual BEFORE using
machine.
To get a new manual,
call (800) 523-4777 or
go to www.grizzly.com.
510
505
509
grizzly.com
REF PART # DESCRIPTION
501 P0834501 MACHINE HAZARDS LABEL
502 P0834502 CUTTERHEAD WARNING LABEL
503 P0834503 MACHINE ID LABEL
504 P0834504 ELECTRICITY LABEL
505 P0834505 UP-DOWN LABEL
506 P0834506 GRIZZLY NAME PLATE (LARGE)
507 P0834507 MODEL NUMBER LABEL
Safety labels warn about machine hazards and ways to prevent injury. The owner of this machine
MUST maintain the original location and readability of the labels on the machine. If any label is
removed or becomes unreadable, REPLACE that label before using the machine again. Contact
Grizzly at (800) 523-4777 or www.grizzly.com to order new labels.
BUY PARTS ONLINE AT GRIZZLY.COM!
-54-
Scan QR code to visit our Parts Store.
Labels & Cosmetics
502
Cutterhead
Failure to keep hands clear exposed between Failure to keep hands clear
of cutterhead will result in of cutterhead will result in
these lines.
serious personal injury. serious personal injury.
G0834
508
Specifications WARNING!
Motor: 5 HP, 230V, Single-Phase, 60 Hz To reduce the risk of serious injury when using this machine:
Full-Load Current: 30A 1. Read and understand owner's manual 10. Turn motor OFF and disconnect power
Cutterhead: Spiral w/Indexable Inserts before operating.
Number of Inserts: 96 2. Always wear approved eye protection
Replacement Inserts: H7354 and respirator. 11. Tie back long hair, roll up sleeves, and
Max Depth of Cut Per Pass: 1/8" 3. Only plug power cord into a grounded
Max Rabbeting Depth: 3/8" outlet.
Cutterhead Speed: 4950 RPM 4. Except when rabbeting, keep all guards 12. Before starting, ensure tables and fence
Cuts Per Minute: 39,600 in place and in proper operating
Fence Tilt: 45º, 90º, 135º condition. Always replace guard after
rabbeting. 13. Do not joint boards with cracks, loose
Table Size: 12-3/4" x 84-1/4"
Weight: 1080 lbs. 5. Never cut workpieces smaller than 8"
14. DO NOT use in wet locations or rain.
long, 3/4" wide, or 1/2" thick.
6. Always use push blocks when face 15. Always support workpiece against fence
planing.
7. Keep hands at least 4" away from 16. Always feed workpiece against
cutterhead.
8. Never cut deeper than 1/8" on a single
pass. 17. Prevent unauthorized use by children or
9. Be aware of "kickback" hazards and
how to prevent them.
507
REF PART # DESCRIPTION
508 P0834508 GRIZZLY.COM LABEL
509 P0834509 TOUCH-UP PAINT, GRIZZLY GREEN
510 P0834510 INJURY/SHOCK HAZARD LABEL
511 P0834511 READ MANUAL LABEL
512 P0834512 TOUCH-UP PAINT, GREY PUTTY
513 P0834513 EYE/HEARING/LUNG WARNING LABEL
Model G0834 (Mfd. Since 12/17)
before changing inserts, adjusting
tables/fence, or servicing.
DO NOT wear loose clothing, gloves, or
jewelry. 503
are adjusted/secured properly and
cutterhead inserts are secure.
knots, tramp metal, or any defects.
and table when cutting.
cutterhead rotation. Never move
workpiece backward while feeding.
untrained users; restrict access or
disable machine when unattended.
504
505
506