Carrier Ecologic Series 3 Controls, Start-Up, Operation, Service, And Troubleshooting page 47

ALARM/ALERT ALARM OR
CODE ALERT
7 Alert
8 Alert
9 Alarm
10 Alarm
11 Alert
12 Alert
15 Alert
16 Alert
17 Alert
18 Alert
21 Alert
22 Alert
23 Alert
24 Alert
25 Alert
26 Alert
27 Alert
28 Alert
29 Alert
30 Alert
Table 36 — Alarm and Alert Codes (cont)
WHY WAS THIS
DESCRIPTION
ALARM GENERATED?
Cir. A Discharge Gas Thermistor outside
Thermistor Failure range of –40 to 245 F
(–40 to 118 C) or DGT
> 210 F (98.9 C)
Cir. B Discharge Gas Thermistor outside
Thermistor Failure range of –40 to 245 F
(–40 to 118 C) or DGT
> 210 F (98.9 C)
Cooler Leaving Fluid Thermistor outside
Thermistor Failure range of –40 to 245 F
(–40 to 118 C)
Cooler Entering Fluid Thermistor outside
Thermistor Failure range of –40 to 245 F
(–40 to 118 C)
Condenser Leaving Thermistor outside
Fluid Thermistor Failure range of –40 to 245 F
(–40 to 118 C)
Condenser Entering Thermistor outside
Fluid Thermistor Failure range of –40 to 245 F
(–40 to 118 C)
Compressor A1 High Thermistor outside
Motor Temperature range of –39.9 to 245 F
(–39.9 to 118 C) for 5
consecutive readings
Compressor A2 High Thermistor outside
Motor Temperature range of –39.9 to 245 F
(–39.9 to 118 C) for 5
consecutive readings
Compressor B1 High Thermistor outside
Motor Temperature range of –39.9 to 245 F
(–39.9 to 118 C) for 5
consecutive readings
Compressor B2 High Thermistor outside
Motor Temperature range of –39.9 to 245 F
(–39.9 to 118 C) for 5
consecutive readings
External Reset Temper- Thermistor outside
ature Thermistor Failure range of –40 to 245 F
(–40 to 118 C)
Circuit A Discharge Calibration offset more
Pressure Transducer than 6 PSIG (41 kPa) or
Failure Voltage ratio (volts read/
ref. voltage) more than
99.9% or less than 0.5%
Circuit B Discharge Calibration offset more
Pressure Transducer than 6 PSIG (41 kPa) or
Failure Voltage ratio (volts read/
ref. voltage) more than
99.9% or less than 0.5%
Circuit A Suction Calibration offset more
Pressure Transducer than 6 PSIG (41 kPa) or
Failure Voltage ratio (volts read/
ref. voltage) more than
99.9% or less than 0.5%
Circuit B Suction Calibration offset more
Pressure Transducer than 6 PSIG (41 kPa) or
Failure Voltage ratio (volts read/
ref. voltage) more than
99.9% or less than 0.5%
Comp A1 Oil Pressure Calibration offset more
Transducer Failure than 6 PSIG (41 kPa) or
Voltage ratio (volts read/
ref. voltage) more than
99.9% or less than 0.5%
Comp A2 Oil Pressure Calibration offset more
Transducer Failure than 6 PSIG (41 kPa) or
Voltage ratio (volts read/
ref. voltage) more than
99.9% or less than 0.5%
Comp B1 Oil Pressure Calibration offset more
Transducer Failure than 6 PSIG (41 kPa) or
Voltage ratio (volts read/
ref. voltage) more than
99.9% or less than 0.5%
Comp B2 Oil Pressure Calibration offset more
Transducer Failure than 6 PSIG (41 kPa) or
Voltage ratio (volts read/
ref. voltage) more than
99.9% or less than 0.5%
Circuit A Economizer Calibration offset more
Transducer Failure than 6 PSIG (41 kPa) or
Voltage ratio (volts read/
ref. voltage) more than
99.9% or less than 0.5%
ACTION TAKEN
BY CONTROL
Circuit A shut down
Circuit B shut down
Chiller shut down
Uses 0.1° F/% Total
Capacity as rise/ton
None. Chiller continues
to run.
None. Chiller continues
to run.
Compressor A1 shut
down
Compressor A2 shut
down
Compressor B1 shut
down
Compressor B2 shut
down
Reset disabled. Runs
under normal control/set
points.
Circuit A shut down
Circuit B shut down
Circuit A shut down
Circuit B shut down
Comp A1 shut down
Comp A2 shut down
Comp B1 shut down
Comp B2 shut down
Circuit A shut down
47
PROBABLE
RESET METHOD
CAUSE
Manual Thermistor failure, motor
cooling solenoid failure
or wiring error.
Manual Thermistor failure, motor
cooling solenoid failure
or wiring error.
Automatic Thermistor failure, dam-
aged cable/wire or wir-
ing error.
Automatic Thermistor failure, dam-
aged cable/wire or wir-
ing error.
Automatic Thermistor failure, dam-
aged cable/wire or wir-
ing error.
Automatic Thermistor failure, dam-
aged cable/wire or wir-
ing error.
Manual Thermistor failure, motor
cooling (all), or Econo-
mizer (2 comp. circuits)
solenoid failure.
Manual Thermistor failure, motor
cooling (all), or Econo-
mizer (2 comp. circuits)
solenoid failure.
Manual Thermistor failure, motor
cooling (all), or Econo-
mizer (2 comp. circuits)
solenoid failure.
Manual Thermistor failure, motor
cooling (all), or Econo-
mizer (2 comp. circuits)
solenoid failure.
Automatic Thermistor failure or wir-
ing error.
Automatic Transducer failure,
power supply failure, or
wiring damage/error.
Automatic Transducer failure,
power supply failure, or
wiring damage/error.
Automatic Transducer failure,
power supply failure, or
wiring damage/error.
Automatic Transducer failure,
power supply failure, or
wiring damage/error.
Automatic Transducer failure,
power supply failure, or
wiring damage/error.
Automatic Transducer failure,
power supply failure, or
wiring damage/error.
Automatic Transducer failure,
power supply failure, or
wiring damage/error.
Automatic Transducer failure,
power supply failure, or
wiring damage/error.
Automatic Transducer failure,
power supply failure, or
wiring damage/error.