Thick; Letterhead; Admin. Management Administrator No; Postcard - Oki MC160MFP Maintenance Manual

Oki Data CONFIDENTIAL
12.3 TRAY1 PAPER SETUP
11.3 TRAY1 PAPER SETUP
Function • Sets the type and size of the paper loaded in tray1.
• When the type and size of the paper loaded in tray1 have been changed
Use
• The default setting varies according to the voltage of the printer.
TRAY1 PAPER TYPE
• The default setting is PLAIN PAPER.
"PLAIN PAPER" / LETTERHEAD / THICK 1 / THICK 2 / LABELS /
ENVELOPE / POSTCARD
TRAY1 PAPER SIZE
• Default setting of paper size depend on the marketing area setting.
USA and Canada: "LETTER", Other country: "A4"
<PLAIN PAPER>
"A4" / B5 / A5 / LEGAL / "LETTER" / G LETTER / STATEMENT / EXECUTIVE / FOLIO /
OFICIO / G LEGAL / CUSTOM(PLAIN)
NOTE
• If [CUSTOM (PLAIN)] is selected as the paper size, specify settings for LENGTH
(195 to 356 mm) and WIDTH (92 to 216 mm) separately.
Setting/
procedure <LETTERHEAD>
"A4" / B5 / A5 / "LETTER" / G LETTER / STATEMENT / EXECUTIVE
<THICK 1, THICK 2>
"A4" / B5 / A5 / "LETTER" / G LETTER / STATEMENT / EXECUTIVE / CUSTOM(THICK)
NOTE
• If [CUSTOM (THICK)] is selected as the paper size, specify settings for LENGTH
(184 to 294 mm) and WIDTH (92 to 216 mm) separately.
<LABELS>
"A4" / B5 / A5 / "LETTER" / G LETTER / STATEMENT / EXECUTIVE
<ENVELOPE>
"C6" / DL
<POSTCARD>
"J-POSTCARD"
44292401TH Rev.1
• The ADMIN. MANAGEMENT menu is accessible only by the administrator.
To display the settings for this menu, select [ADMIN. MANAGEMENT], use the keypad to
type in the 6-digit administrator access code, and then press the Select key.
12.4.1 ADMINISTRATOR NO.
Function
11.4 ADMIN. MANAGEMENT 12.4 ADMIN. MANAGEMENT
• Use to change the ADMINISTRA TOR NO.
Use
• The ADMIN. MANAGEMENT menu is accessible only by the administrator.
• The default setting is 000000.
To display the settings for this menu, select [ADMIN. MANAGEMENT], use the keypad to
Setting/ type in the 6-digit administrator access code, and then press the Select key.
1. Select [ADMINISTRA TOR NO.] and press the Select key.
procedure
2. Enter the existing 6-digit administrator number and press the Select key.
3. Enter the new 6-digit administrator number and press the Select key.
11.4.1 ADMINISTRATOR NO.
12.4.1 ADMINISTRATOR NO.
Function
12.4.2 REMOTE MONITOR
• Use to change the ADMINISTRA TOR NO.
Use
Function
• The default setting is 000000.
• Set if the phone line connection is to be enabled for Remote Setup Utility.
Use
Setting/
1. Select [ADMINISTRA TOR NO.] and press the Select key.
procedure
• The default setting is OFF.
2. Enter the existing 6-digit administrator number and press the Select key.
Setting/
3. Enter the new 6-digit administrator number and press the Select key.
procedure
12.4.2 REMOTE MONITOR
11.4.2 NETWORK SETTING
12.4.3 NETWORK SETTING
A. TCP/IP
Function
• Set if the phone line connection is to be enabled for Remote Setup Utility.
Use
Function • Enables TCP/IP
• The default setting is OFF.
• To specify that the printer is connected to a TCP/IP network.
Setting/
procedure Use ENABLE: Print can be made at TCP/IP environment.
DISABLE: Print cannot be made at TCP/IP environment.
• The default setting is ENABLE.
Setting/
12.4.3 NETWORK SETTING
procedure
DISABLE / "ENABLE"
A. TCP/IP
B. IP ADDR. SETTING
Function • Enables TCP/IP
Function • To specify that the printer is connected to a TCP/IP network. • Sets the IP address of the printer used for the network.
Use ENABLE: Print can be made at TCP/IP environment.
Use • To set the printer's IP address.
DISABLE: Print cannot be made at TCP/IP environment.
• The default setting is AUTO.
• The default setting is ENABLE.
Setting/
"AUTO" / SPECIFY
procedure
DISABLE / "ENABLE"
• If AUTO is selected, the IP address is automatically acquired from the DHCP server.
Setting/
B. IP ADDR. SETTING
NOTE
procedure
• AUTO is only enabled if there is a DHCP server available on the network.
Function • Sets the IP address of the printer used for the network.
• When AUTO is selected, there is no need to set the SUBNET MASK or GATEWAY
Use • To set the printer's IP address.
setting.
• The default setting is AUTO.
• If SPECIFY is selected, the screen for entering the IP address appears.
"AUTO" / SPECIFY
• If AUTO is selected, the IP address is automatically acquired from the DHCP server.
Setting/
NOTE
procedure
• AUTO is only enabled if there is a DHCP server available on the network.
• When AUTO is selected, there is no need to set the SUBNET MASK or GATEWAY
setting.
• If SPECIFY is selected, the screen for entering the IP address appears.
ADJUSTMENT/SETTING
"OFF" / ON
"OFF" / ON
106 /